JCHR35H6 Series Remote Specification

Product Introduction

The JCHR35H6 series remote control is available with 5, 6, 9, 13, or 15 buttons, named JCHR35H6A, JCHR35H6B, JCHR35H6C, JCHR35H6D, and JCHR35H6E, respectively. The JCHR35H6 series remotes share the same PCB board, with variations only in the screen printing.

Product Parameters

• Wireless frequency: 2.4G Hz
• Features blue backlight and one tricolor light.
• Equipped with a toggle switch for selecting single control or synchronization when two control boxes are synchronized.
• Power supply: AAA 4.5V
• Low power consumption: standby power consumption ≤ 10uA
• Remote control distance: ≤ 5 meters
• Button type: silicone button

Optional Features

Usage

• Compatible control boxes: Home appliance or medical control boxes.
• Environment: Indoor Use
• Storage and transportation temperature: -25°C to 70°C

Dimensions

The remote measures 151mm in length, 51mm in width, and 16.2mm in thickness.

Button Function

Code Matching Function

This function allows the remote to control the corresponding control box after successful matching.

Method:

1. After the control box is plugged into AC power, enter the code matching mode.
2. Simultaneously press the "M1 Up + M2 Up" buttons on the remote.
3. When the control box emits a "tick" sound and the remote's backlight flashes twice, the code matching is successful.

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

RF warning for Portable device:

The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ISED RSS Warning/ISED RF Exposure Statement

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

ISED RF exposure statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirement.

Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour un autre environnement. Ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.