Infinix HOT 50i
X6531 User Manual
Exploded Diagram Specification
The following table details the components of the Infinix HOT 50i:
| Component ID | Component Name | Component ID | Component Name |
| 1 | TP | 2 | MAIN PBC |
| 3 | SIM CARD HOLDER | 4 | FINGERPRINT FPC |
| 5 | SIDE KEY | 6 | WATERPROOF MYLAR |
| 7 | GROUNDED COPPER FOIL | 8 | FRONT SHELL |
| 9 | POST-FLASH CONDUCTIVE FOAM | 10 | FRONT-FACING CAMERA |
| 11 | SUPPORT FOAM | 12 | POST-FLASH CONDUCTIVE FOAM |
| 13 | TOP COOLING FIN | 14 | REAR CAMERA LENS |
| 15 | REAR FLASH FPC | 16 | MIDDLE BEZEL |
| 17 | DECORATIVE LENS | 18 | SCREW |
| 19 | BATTERY COVER | 20 | TYPE-C RUBBER SLEEVE |
| 21 | UP TRUMPET | 22 | VICE BOARD |
| 23 | HEAT SINK IN THE MIDDLE FRAME | 24 | IC COPPER FOIL |
| 25 | REAR EARTHED COPPER FOIL | 26 | MOTOR |
| 27 | TRUMPET | 28 | CAMERA MOUNT |
| 29 | BATTERY | 30 | FINISHING COMPONENT |
| 31 | HEADSET RUBBER SLEEVE | 32 | SIDE KEY FPC |
| 33 | BOT COOLING FIN | 34 | COOLING FIN TRUMPET |
| 35 | REAR SECONDARY CAMERA LENS | 36 | FRONT CAMERA GROUND COPPER FOIL |
Know Your Phone
The front of the phone features:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button & side fingerprint sensor
SIM/SD Card Installation
To install SIM/SD cards:
- Power off your phone.
- Refer to the diagram for SIM/SD card installation. The diagram shows a phone with two SIM card slots (SIM1, SIM2) and one SD card slot.
Charging the Phone
You can charge your phone using the provided Infinix charger and cable, or by connecting it to a computer via a USB cable. It is recommended to use only Infinix-approved chargers and cables to avoid damaging the phone and voiding the warranty.
The diagram shows a USB Type-C cable being plugged into the phone's charging port.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Information to the user:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations. The standards include a substantial safety margin to assure the safety of all persons.
The SAR limit for the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. The Infinix HOT 50i (X6531, FCC ID: 2AIZN-X6531) has been tested against this SAR limit. The highest reported SAR values are 0.796 W/kg for use at the ear and 0.633 W/kg when properly worn on the body.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Licensing and Trademarks
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, and DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System: Android™. Android is a trademark of Google LLC.
