Infinix X666 User Manual

Explosion Diagram Specification

The following table details the components of the Infinix X666 as shown in the explosion diagram:

Know Your Phone

The Infinix X666 features the following external components:

• 1. Front camera
• 2. Volume + key
• 3. Volume - key
• 1. Power key & side fingerprint sensor

SIM/SD Card Installation

To install your SIM and SD cards:

1. Power off the mobile device.
2. Refer to the provided diagram for correct SIM/SD card placement.

Charging the Phone

You can charge your Infinix X666 using a charger or by connecting it to a computer via a USB cable (included with the phone). It is recommended to use only Infinix-approved chargers and cables to prevent device damage and warranty invalidation.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

• (1) This device may not cause harmful interference.
• (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

SAR Information Statement

Your wireless phone is a radio transmitter and receiver designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards developed through periodic and thorough evaluation of scientific studies, including a substantial safety margin.

The exposure standard for wireless mobile phones employs the Specific Absorption Rate (SAR). The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted with the phone transmitting at its highest certified power level in all tested frequency bands. The actual SAR level of the phone while operating can be well below the maximum value, as the phone is designed to operate at multiple power levels to conserve energy.

The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid.

FCC ID: 2AIZN-X666

Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com.

In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

DTS Information

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the DTS logo, and the DTS logo combination are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

Operating System

Operating System: Android™ OS

Android is a trademark of Google LLC.