DD7600E Series Handheld Emitter Instruction

Technical Specification

Instruction Of Buttons

Front:

• JOG UP button
• JOG DOWN button
• Setting button (P2)

Back:

• DIP switch

Emitter Types:

• DD7600E Single-channel emitter
• DD7602E 15-channel dual control emitter
• DD7660E Single-channel emitter
• DD7662E 15-channel dual control emitter

Key Symbol:

• UP: ⬆️
• STOP: STOP
• DOWN: ⬇️
• CH-: ➖
• CH+: ➕
• Brightness+: ?+
• Light on/off: ?
• Brightness-: ?-
• P2: P2

Warning

1. The emitter should not be exposed to moisture or be struck heavily, as this may affect its lifespan.
2. If the emitter becomes less sensitive or the radio range shortens, check and replace the battery if necessary.
3. Do not use different types of batteries to avoid dangerous risks.
4. Dispose of used batteries properly.

1. Jog / Tilt Mode

Note: The JOG UP and JOG DOWN buttons control the currently selected emitter. Releasing the button sends the code.

This function is available in all series of emitters.

• JOG UP x 1: Motor jog up
• JOG DOWN x 1: Motor jog down

2. DIP Switch Function

Note: The factory defaults to "1" and the mode is bidirectional.

Using tools to toggle the DIP switch:

• Turn the dial switch to "1": Bi-directional mode
• Turn the dial switch to "ON": Uni-directional mode

Following 3/4 Only Apply to Emitter Without LCD Display

3. Enable / Disable Sun Detection (In bi-directional mode)

Note: Long press the JOG DOWN button until the LED stays on for 3 seconds, then the operation is effective. Press the STOP button to exit the setting.

• UP x 1: Sun detection is enabled
• JOG DOWN x 3 (LED always on): Sun detection is disabled

4. Lock / Unlock Combo-key Operation

Note: 1. Both setting buttons (P2) can be used. 2. The factory default is unlock status; repeat the operation to switch between lock and unlock states. 3. When combo-keys are locked, pressing them will not send a signal, and the LED will not flash.

• Press and hold STOP button for more than 15s (LED always on): Lock status, combo-key is invalid.
• P2 x 1: Flashes slowly for 3s
• P2: Flashes quickly for 3s: Unlock status, combo-key is available.

Following 5/6/7/8/9 Only Apply to Emitter With LCD Display

5. Enable / Disable Sun Detection (In bi-directional mode)

Note: The motor must be paired with a wind-rain-sun sensor. The sun detection function can only be enabled/disabled when the motor has a limit set.

• JOG DOWN x 3s: Sun detection is enabled
• DOWN x 1: Sun detection is disabled

6. Lock / Unlock Combo-key Operation

Note: 1. Both setting buttons (P2) can be used. 2. The factory default is unlock status; repeat the operation to switch between lock and unlock states. 3. Under lock status, the combo-keys do not work; under unlock status, the combo-keys work normally.

• Press and hold STOP button for more than 15s: Display "L". Combo-key is locked.
• P2 x 1: Release button. Display "0". Combo-keys unlocked.

7. Set Number Of Channels

Note: To exit quickly, press UP or DOWN button. Repeat the process to adjust the maximum channels.

• Press CH- and CH+ simultaneously and hold: Display "ㄷ".
• Press CH- and CH+ simultaneously and hold: Display "15". The effective channels have been set successfully.

8. Battery Check Function (In bi-directional mode)

Note: 1. Only paired motors can have their battery checked. The current channel can only check one paired motor at a time. 2. Only motors paired by long pressing the STOP button for 25s will have the battery check function.

• When the motor is charging: The LCD will display the battery symbol and current battery capacity.
• When the motor is not charging: The LCD will display the current battery capacity.

9. Motor Percentage Running (In bi-directional mode)

Note: After setting is completed, do not operate any buttons; the command will be sent automatically after 3 seconds.

• Press JOG UP or JOG DOWN button to select the desired percentage value (00~100).

FCC Warning Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.