BIGBIG WON ARMOR-X Controller

Introduction

The BIGBIG WON ARMOR-X is an advanced accessory designed to enhance your gaming experience. This guide provides detailed instructions on its features, installation, and operation.

Parts Identification

The ARMOR-X controller features the following components:

• USB-C Port: For charging and data transfer.
• LED1: Indicates connection status and configuration set.
• LED2: Indicates remapping, burst, and macro status.
• M1, M2, M3, M4 Buttons: Programmable rear extension buttons.
• AB Button: Function button, often used in combination.
• FN Button: Function button, used for accessing various modes.
• LT/RT Buttons: Trigger buttons.
• Power Button: Turns the device on/off.
• Pairing Button: Used for wireless pairing.
• USB-C Charging Port: Port for charging the device.
• Indicator Light: General status indicator.
• USB-C Data/Charging Cable: Included cable.
• 2.4G Receiver: Wireless receiver for connecting to consoles/PC.

Diagram Description: The controller has a central hub with function buttons (FN, AB, Power, Pairing) and LED indicators. It features four programmable rear buttons labeled M1, M2, M3, M4. It also includes standard trigger buttons (LT/RT) and a USB-C port for charging and connection.

Package Contents and Supported Consoles

Package Contents

Supported Consoles

Rear Button Installation

Follow these steps to install the rear button accessory:

1. Remove the controller's battery cover.
2. Install the ARMORX accessory into the battery compartment, ensuring it is securely fixed.
3. Insert ARMORX's flexible cable into the USB port of the Xbox Series controller.

Note: For optimal performance, charge the ARMORX before its first use. A full charge takes approximately 2.5 hours.

Power On and Connection

The ARMORX controller natively supports Xbox, PC, and Nintendo Switch platforms.

To power on: Press and hold the ARMORX power button. Insert the 2.4G receiver into the console's USB port. The ARMORX will automatically detect the platform and switch to the appropriate mode.

LED Indicators:

• LED1 Slow Flashing: Reconnecting to the receiver.
• LED1 Fast Flashing: Pairing with the receiver.
• LED1 Solid: Correctly connected to the receiver (the receiver's indicator behaves similarly).
• After a successful connection, LED1 and the receiver indicator will be solid and match the platform's color.
• LED2 Flashing: Communication between ARMORX and the controller is not functioning.
• LED2 Solid: Communication is regular.

For Nintendo Switch: Ensure "Settings - Controllers and Sensors - Pro Controller Wired Communication" is enabled in the console's settings.

Re-pairing

The ARMORX and its receiver are pre-paired from the factory. If the connection becomes abnormal, re-pairing is necessary. Follow these steps:

1. After powering on ARMORX, press and hold FN + AB until LED1 flashes rapidly, indicating pairing mode.
2. Insert the receiver into the console and press and hold the pairing button on the receiver until its indicator flashes rapidly, indicating receiver pairing mode.
3. At this point, both ARMORX and the receiver indicators will flash rapidly, signifying they are pairing. Wait until LED1 and the receiver indicator are solid, indicating successful pairing.

Button Remapping

The ARMORX controller allows you to remap controller buttons to the rear buttons. Quick shortcuts support remapping of M1/M2/M3/M4. The companion APP also enables remapping of A/B/X/Y, LT/RT/LB/RB, RS/LS buttons.

1. Set Button Remapping: Press AB + (M1/M2/M3/M4). LED2 will emit a breathing green light, indicating remapping mode. Press the front button you wish to map to M1/M2/M3/M4. LED2 will flash twice in green, confirming successful remapping.
2. Cancel Single Button Remapping: Press and hold the rear button (M1-M4) you wish to unmap, then double-click AB. LED2 will flash twice in green, confirming successful cancellation.
3. Cancel All Button Remapping: Double-click B. LED2 will flash twice in green, confirming all remapping has been cancelled.

Burst Mode Setup

The ARMORX controller supports burst mode for the following buttons: A/B/X/Y, directional buttons (↑/↓/←/→), LT/RT/LB/RB, M1-M4, RS/LS.

1. Set Burst Mode: Press and hold FN + "the button to set". LED2 will flash orange, indicating burst mode activation. When burst is triggered, LED2 will flash according to the burst frequency.
2. Disable Burst Mode: Press and hold the button for which burst mode is set, then double-click AB. LED2 will flash twice in orange, confirming successful cancellation.
3. Cancel All Burst Modes: Double-click AB. LED2 will flash twice in orange, confirming all burst modes have been cancelled.
4. Adjust Burst Frequency: Press and hold FN + ↑ to cycle through three frequencies: 5/s, 10/s, and 15/s. The burst frequency is independent of other configurations and is universal.

Macro Recording

The ARMORX controller supports macro recording for buttons A/B/X/Y, directional buttons (↑/↓/←/→), LT/RT/LB/RB, RS/LS, and eight-way stick directions. Each macro must be assigned to a rear button (M1-M4) as a trigger.

1. Record Macro: Press and hold FN + (M1/M2/M3/M4) for 3 seconds. LED2 will emit a breathing red light, indicating macro recording mode. Press the controller buttons to record your macro sequence. After recording, click FN. LED2 will flash twice in red, indicating the end of recording. During macro playback, LED2 will flash red until the macro completes.
2. Cancel Single Macro: Press and hold the rear button (M1-M4) assigned to the macro, then double-click FN. LED2 will flash twice in red, confirming successful cancellation.
3. Cancel All Macros: Double-click FN. LED2 will flash twice in red, confirming all macros have been cancelled.

Vibration Adjustment

The ARMORX controller allows active adjustment of vibration intensity for both the controller motor and the trigger motors. You can choose from three intensity levels or turn vibration off.

1. Trigger Vibration: Press FN + ← to cycle through four trigger vibration levels: Strong, Medium, Weak, and Off.
2. Controller Vibration: Press FN + → to cycle through four controller vibration levels: Strong, Medium, Weak, and Off.

Configuration Switching

ARMORX can save up to three integrated configurations. Press the designated button (typically FN) to cycle through these configurations. The three configuration sets correspond to the following LED1 colors:

• LED1 Orange: Configuration Set 1.
• LED1 Green: Configuration Set 2.
• LED1 Blue: Configuration Set 3.

Battery Information

The ARMORX-Pro is equipped with a 1300mAh lithium battery, providing approximately 10 hours of usage. Key factors influencing battery life include vibration intensity and frequency; higher frequency vibrations significantly reduce battery duration.

The charging power is 5V/1A, and a full charge for a depleted battery takes about 2 hours.

• Low Battery Indicator: When the battery is low, the controller will vibrate three times consecutively, and LED1 will flash rapidly red every 5 minutes.
• Charging Indicator: During charging, LED1 will be solid red. It will turn solid green upon a full charge.

Support and Community

For detailed video tutorials and further assistance, visit the official BIGBIG WON support page:

https://www.bigbigwon.com/support/

For questions or issues, contact support via:

• Amazon: Navigate to the product page, then Seller Profile, and select "Ask a question".
• Customer Service Email: support@bigbigwon.com

Welcome to the BIGBIG WON Community

Join the BIGBIG WON community to connect with fellow gamers. Participate on Discord and follow our social media channels for the latest offers, event coverage, and opportunities to review BIGBIG WON hardware.

Community Channels: Discord, Instagram, Twitter, TikTok, YouTube, @BIGBIG WON