WORKPRO 6-in-1 Heavy-Duty Staple Gun
Model Numbers: W023035A, W023036A
Product Overview
This document provides instructions for the WORKPRO 6-in-1 Heavy-Duty Staple Gun. The staple gun is versatile and can be used for various tasks, including upholstery, framing, and low-voltage cabling.
Key Features & Components
The staple gun features:
- Handle: The main grip for operating the tool. (Also referred to as Griff, Poignée, Maniglia, Mango, ハンドル in other languages).
- High/Low Power Switch: Allows adjustment of staple driving force. (Also referred to as High-/Low-Power-Schalter, Interrupteur élevé / faible, Interrutore Alta / Bassa, Interruptor de potencia alta / baja, 強/弱モードスイッチ).
- Staple Reload Window: Indicates the level of staples remaining. (Also referred to as Fenster zum Neuladen von Heftklammern, Fenêtre de recharge des agrafes, Finestra di ricarica punti, Ventana para la recarga de grapas, ウインドウ).
- Staple Exit Area: Where the staple is driven into the material. (Also referred to as Ausgangsbereich für Heftklammern, Zone de sortie des agrafes, Area di uscita punti, Área por donde salen las grapas, 射出口).
- Magazine Release Latch: Used to open the staple magazine for loading. (Also referred to as Magazine Entriegelung, Verrou de déblocage du chargeur, Fermo di rilascio caricatore, Pestillo de liberación del cartucho, マガジン).
- Load Staples/Brads Here: The channel for inserting staples, brads, or pins. (Also referred to as Laden Sie hier Heftklammern / Brads, Charger les agrafes / clous ici, Carica qui le graffette / brad, Carga de grapas, 装填レール).
- Front Wire Guide: Aids in guiding wires when stapling cables. (Also referred to as Vordere Kabelführung, Guide-fil avant, Guida di filo anteriore, Guía frontal para cable, フロントワイヤーガイド).
- Rear Wire Guide: Also aids in guiding wires. (Also referred to as Kabelführung hinten, Guide-fil arrière, Guida di filo posteriore, Guía trasera para cable, リアワイヤーガイド).
To Operate
Follow these steps to operate the staple gun:
- Hold the staple gun upside down and release the loading latch. Pull the slide open. (Refer to Figure 1).
- Insert a stick of staples into the bottom channel with the legs pointing up. For narrow flat crown, cable, brads, and pins, place them only on the left side. Push the slide closed, ensuring the latch engages. (Refer to Figure 2).
- For brads, ensure nail heads point down. For pins, ensure the flat end points down and the sharp tip points up. Push the slide closed, ensuring the latch engages. (Refer to Figure 3).
- Place the staple exit area on the material where the staple is to be driven. Grasp the tacker and depress the handle until the mechanism releases and drives the staple. For best results, apply downward pressure to keep the exit area firmly against the material.
To Clear or Unload
Open the channel as when loading. Remove any jammed staples or unload the staple stick. Close the channel as when loading.
To Lock Handle Down for Storage
Ensure the staple gun is unloaded. Hold the handle down, pull backward to engage the handle lock (See Figure 4). Push the handle forward to release the grip (See Figure 5).
Safety Instructions
⚠️ WARNING:
- Keep out of reach of children.
- Never aim the staple exit at anyone.
- Wear safety glasses when operating the tacker.
- Know the materials you are stapling.
- Watch out for potential hazards such as electrical wires.
- Do not overreach, as this can cause loss of balance or secure footing.
- Do not staple live wires.
Staple Length Guidelines
The staple gun is compatible with various staple lengths and types:
| Staple Type | Length | Recommended Uses |
|---|---|---|
| Heavy Duty | 1/4" (6mm), 5/16" (8mm), 3/8" (10mm), 1/2" (12mm), 9/16" (14mm) | Window screens & shades, light draperies, shelf papers, closet lining, etc. |
| Light Duty | 1/4" (6mm), 5/16" (8mm), 3/8" (10mm), 1/2" (12mm), 9/16" (14mm) | Light upholstery and other relatively thin materials. |
| Narrow Flat Crown | 1/4" (6mm), 5/16" (8mm), 3/8" (10mm), 1/2" (12mm), 9/16" (14mm) | Insulation, weather stripping, wire mesh, carpet pads, canvas and other materials of moderate strength where material thickness is up to about 3/16'' maximum. |
| Cable | 3/8" (10mm), 7/16" (11mm), 1/2" (12mm), 9/16" (14mm) | For cables up to 6mm diameter, max 50V. Used for holiday lights, antenna wiring, telephone wiring, cable TV, alarm system wire, audio system. |
| Brad | 5/8" (15mm) | Picture framing, small molding. |
| Pin | 5/8" (15mm) | Typically used for delicate materials or where a nail head is not desired. |
Tacker: Applications
- Low Voltage Cabling: For cables less than 6mm diameter and 50V max. Includes holiday lights, antenna wiring, telephone wiring, cable TV, alarm system wire, audio system.
- Canvas/Screen Applications: Upholstering, decor, wire, stretching canvas-art, mesh/screening, framing fabric, needlepoint, framing.
Staple Compatibility
The staple gun is compatible with staples from brands such as Arrow®, DEWALT®, STANLEY®, and RAPID®.
Heavy Duty Staples: Arrow® T50®; DEWALT® DWHTTA705, DWHTTA706, DWHTTA708; STANLEY® TRA704, TRA705, TRA706, TRA708, TRA709; RAPID® NO.140.
Light Duty Staples: Arrow® JT21®; STANLEY® TRA204, TRA205, TRA206, TRA208, TRA209; RAPID® NO.53.
Narrow Flat Crown Staples: Arrow® T20™; STANLEY® CT306, CT308.
Cable Staples: Arrow® T25™; STANLEY® CT106, CT107, CT108, CT109; RAPID® NO.36.
Brads (18 GA.): 5/8" (15mm) Arrow® BN18™; DEWALT® DWHTBN625; STANLEY® SWKBN625; RAPID® NO.8.
Pins (18 GA.): 5/8" (15mm) RAPID® NO.9.
Note: Some staples may not fit if the top is not a circular arc.
Manufacturer Information
Manufactured by Hangzhou Great Star Industrial Co., Ltd.
Address: No.35 Jiuhuan Road, Jiubao Town, Hangzhou 310019, China
Website: www.greatstartools.com
