Flydigi Wasp: Installation and Customization Guide

Installation Guide

Follow these steps to install your Flydigi Wasp controller onto your iPhone.

1. Power On Wasp: Slide the power switch to the left. The indicator light will turn orange.

2. Prepare Controller: Pull down the switch on the back of the controller. The yellow handle will pop up.

3. iPhone Setting: Ensure the portrait orientation lock on your iPhone is turned off.

4. Connect iPhone: Lock your iPhone's screen until it is blank. Then, plug your iPhone into the Wasp controller.

5. Secure iPhone: Press the yellow handle until your iPhone is securely seated.

6. Unlock iPhone: Unlock your iPhone.

7. Enjoy your game!

Note: The Wasp-X image shown in the original documentation is for demonstration purposes only. Actual product may vary.

Troubleshooting: If the Wasp controller does not function properly or disconnects randomly, try turning your iPhone's screen off and then back on again.

Customize Buttons within Games

The Flydigi Wasp allows you to directly control games downloaded from the App Store. Button mapping is achieved by assigning virtual buttons within the game to specific points on the Wasp controller.

The intersection of the X and Y axes represents the fixed projection point for each of the Wasp's four mappable buttons. To map a button, drag a virtual button (e.g., 'shoot' or 'aim') in your game to one of these four points. A mapping ruler is provided to assist with precise placement.

After installation, launch your App Store games and begin playing. The Wasp offers two joystick modes: FPS mode (larger radius for more sensitive control) and MOBA mode (smaller radius). To switch between modes, press and hold the logo button for three seconds.

Example: Fortnite

In Fortnite, navigate to the 'HUD Layout Tool' within the game settings. Drag the desired virtual button (e.g., 'shoot', 'aim') to the corresponding mapping location on the controller interface. This action maps the physical button on the gamepad to the virtual button in the game. Note that only the Left Trigger supports long pressing; any virtual button requiring a long press should be mapped to the Left Trigger's position.

Remember to save your custom button layout within the game for future sessions.

Compatibility: All mobile FPS games, such as Fortnite and PUBG Mobile, support button customization. For games that do not support button customization, joystick control can still be utilized.

Compliance Note: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Flydigi Wasp Lightning Extension

The Flydigi Wasp Lightning Extension is a specialized cable designed for iPhones. It enables you to use headphones or charge your iPhone simultaneously while using the Wasp controller.

1. Plug your iPhone's lightning cable into the Wasp Lightning Extension.
2. Connect the Wasp Lightning Extension to your iPhone.
3. Install your iPhone into the Wasp controller.
4. Plug the lightning cable into a portable power bank for charging.

Please follow these steps carefully to ensure your iPhone is charged correctly.

Important Player Information

Please adhere strictly to the following instructions to prevent common issues such as unexpected Wasp stoppages or random disconnections.

• Initial Setup: Lock your iPhone's screen before plugging it into the Wasp.
• Gamepad Calibration: To calibrate your gamepad, follow these steps:
  1. Turn off your iPhone's screen.
  2. Plug your iPhone into the Wasp.
  3. Turn on the Wasp and wake up your iPhone's screen.

  This calibration process should be repeated whenever your iPhone is detached from the Wasp.

• Software Recommendation: Download the Flydigi Gamepad Assistant application. This app provides product diagnostics, firmware updates, game guides, and more.

Federal Communications Commission (FCC) Statement

This device has been evaluated and meets general radio frequency (RF) exposure requirements. It can be used in portable exposure conditions without restriction. The power output is sufficiently low that no RF exposure calculation is needed.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Manufacturer Disclaimer: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user's authority to operate the equipment.

FCC Compliance Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for assistance.