Flydigi Wasp-X Mobile Game Controller for iPhone

Getting Started with Your Wasp-X

Follow these steps to set up your Wasp-X controller with your iPhone:

1. Turn on the Wasp-X by sliding the switch to the left. The indicator light will turn orange ?.
2. Pull down the switch on the back of the controller. The yellow handle will pop up.
3. Turn off the portrait orientation lock on your iPhone.
4. Lock your iPhone screen (ensure it is blank) and plug your iPhone into the Wasp-X as shown. (Note: The image in the original document is for demonstration purposes; actual product may vary.)
5. Press the yellow handle until your iPhone is secured.
6. Unlock your iPhone.
7. Enjoy your game! ▶️

If the Wasp-X does not function properly or disconnects randomly ⚠️, please turn the iPhone screen off and then back on.

Customizing Buttons within Games

The Wasp-X allows direct control of games downloaded from the App Store. The intersection of the X and Y axes represents the fixed projection point for corresponding virtual buttons from the game. Each of the four physical buttons on the Wasp-X has its own designated point.

How to Map Buttons:

• Drag a virtual button (e.g., for shooting or aiming) from within the game to one of these four projection points. This establishes the connection between the physical button and the virtual icon.
• A mapping ruler can help you locate these points more precisely.

After installation, run your App Store games. The Wasp-X offers two joystick modes: FPS mode (larger radius) and MOBA mode (smaller radius). Press the logo button ? for three seconds to switch modes.

Example with Fortnite:

1. Go to the 'HUD Layout Tool' within the game.
2. Drag the virtual button to the corresponding mapping location mentioned above. The gamepad button is now mapped to the virtual button.
3. Note: Only the Left Trigger supports long pressing. Any virtual button requiring a long press should be mapped to the Left Trigger's position.
4. Save the game button layout for future use.

All mobile First-Person Shooter (FPS) games (such as Fortnite & PUBG Mobile) support button customization. For games that do not support button customization, joystick control ?️ can be used.

Flydigi Wasp Lightning Extension ⚡

The Flydigi Wasp Lightning Extension is a special extension cable for iPhone. It allows you to use headphones or charge your iPhone while using the Wasp controller.

Setup:

1. Plug the iPhone lightning cable into the Wasp Lightning Extension.
2. Plug the Wasp Lightning Extension into your iPhone.
3. Install your iPhone into the Wasp controller.
4. Plug the lightning cable into a portable power bank.

Please follow these steps carefully to ensure your iPhone is charged correctly.

Important Player Notes & Calibration

Please strictly follow the instructions below to avoid common problems such as unexpected stoppage or random disconnects of the Wasp controller.

Calibrating Your Gamepad: Lock Screen Method

This calibration is recommended whenever your iPhone is detached from the Wasp controller.

1. Turn off the iPhone screen.
2. Plug your iPhone into the Wasp controller.
3. Turn on the Wasp controller and wake up the iPhone screen.

Whenever your iPhone is detached from the Wasp, repeat these steps to re-calibrate.

Flydigi Gamepad Assistant

Download the Flydigi Gamepad Assistant app ? for product diagnostics, firmware updates, game guides, and more.

Federal Communications Commission (FCC) Statement ?

This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction. Power levels are low enough that no RF exposure calculation is required.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device must not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation.

If this equipment causes harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Model Information

Product Names: Wasp-X, Wasp-N

Model Numbers: 2AORE-WASP-X, 2AOREWASPX

Manufacturer: Shanghai Flydigi Electronics Technology Co., Ltd.

Description: Flydigi Wasp One-handed Gamepad (BLE)