Introduction
This manual provides instructions for the JBC MS Electric Desoldering Module, designed for use with DIU & CDD systems.
Packing List
The following items are included:
- Electric Desoldering Module (1 unit)
- Module Cable connector (1 unit, Ref. 0026830)
- Suction Filter (1 unit, Ref. 0821830)
- Filter Box (1 unit, Ref. 0005966, contains 50 filters)
- Cotton Filter (10 units, Ref. 0781046)
- Manual (1 unit, Ref. 0027989)
Features and Connections
The JBC MS Electric Desoldering Module features:
- Control Unit "switch on" Indicator (Power)
- In Use Indicator
- Desoldering Air Filter
Connections:
- Port for Peripheral connection
- Port for Suction Filter connection (to Tool)
Diagram Description: The front view of the JBC MS Electric Desoldering Module shows indicator lights labeled 'Power' and 'In Use' below the JBC logo. The module is identified as 'Desoldering Module'. A dial is visible on the right. The rear view shows a port labeled 'SECTION' for peripheral connection and a circular port for connecting the suction filter, which leads 'to Tool'.
Maintenance
Before carrying out maintenance or storage, always unplug the equipment.
- Keep the casing clean by using a damp cloth. Use a soft cloth for the front side.
- Periodically check all cable and tube connections.
- Keep filters clean to ensure proper solder suction and replace them when necessary.
Important: Do not use sharp pointed objects to open the suction filter.
Components for maintenance:
- Suction Filter (Ref. 0821830)
- Cotton Filters (Ref. 0781046)
- O Ring (Ref. 0007717)
- Filter Cover (Ref. 0004710)
- Paper Filters (Ref. 0005966)
Diagram Description: An exploded view illustrates the components of the suction filter assembly. It shows the main suction filter unit, cotton filters, an O-ring, a filter cover, and paper filters. These are identified by labels such as 'Suction Filter Ref. 0821830', 'Cotton Filters Ref. 0781046', 'O Ring Ref. 0007717', 'Filter Cover Ref. 0004710', and 'Paper Filters Ref. 0005966'.
Guidelines:
- Use original JBC spare parts only.
- Replace any defective or damaged pieces with original JBC spare parts.
- Repairs should only be performed by a JBC authorized technical service.
- Maintenance must not be carried out by children unless supervised.
Safety
⚠️ It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.
- The power cord must be plugged into approved bases and be properly grounded before use. When unplugging, hold the plug, not the wire.
- Do not work on electrically live parts.
- The tool should be placed in the stand when not in use to activate sleep mode. The soldering tip or nozzle, the metal part of the tool, and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position.
- Do not leave the appliance unattended when it is on.
- Do not cover the ventilation grills, as heat can cause flammable products to ignite.
- Avoid flux coming into contact with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves to avoid personal harm.
- Utmost care must be taken with liquid tin waste, which can cause burns.
- This appliance can be used by children over the age of eight and persons with reduced physical, sensory, or mental capabilities or lack of experience, provided they have been given adequate supervision or instruction concerning its use and understand the hazards involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
Specifications
MS Electric Desoldering Module for DIU & CDD
Reference: MS-A
- Net Weight: 1.19 kg / 2.62 lb
- Module Dimension (L x W x H): 225 x 145 x 55 mm / 8.86 x 5.71 x 2.17 in
- Vacuum: 75% / 570 mmHg / 22.4 inHg
- Flow Rate: 9 SLPM
- Ambient Operating Temperature: 10 - 40 °C / 50 - 104 °F
- Total Package Dimensions / Weight (L x W x H): 280 x 195 x 115 mm / 1.50 kg (11.02 x 7.68 x 4.53 in / 3.30 lb)
Complies with CE standards. ESD safe.
Warranty
JBC's 2-year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. For the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
Disposal
This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.
Compliance Marks: CE, EAC
