VIVO 47" x 47" Corner Electric Desk

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

ELECTRICAL SAFETY INSTRUCTIONS

This product is powered by electricity. To avoid burns, fire, and electric shock, please read the following instructions carefully:

• Do not clean the product while power is connected.
• Do not disassemble or replace components while power is connected.
• Never operate the system with a damaged cord or plug. Please contact your seller to replace damaged parts.
• Never operate the system in damp environments or if any electrical components have made contact with liquids.
• Alterations of the given power unit are not allowed.
• Outdoor use is prohibited.

PACKAGE CONTENTS

• A (x1) Left Panel
• B (x1) Middle Panel
• C (x1) Right Panel
• D (x1) Sync Rod
• E (x4) Connecting Plate
• F (x1) Left Crossbar
• G (x1) Right Crossbar
• H (x1) Crossbar Connector
• I (x1) Shelf
• J (x1) Right Leg
• K (x1) Left Leg
• L (x1) Left Side Bracket
• M (x1) Right Side Bracket
• N (x1) AC Adapter
• O (x1) Control Panel
• P (x2) Shelf Brackets
• Q (x2) Hook
• R (x2) Foot Extension
• S (x2) Foot
• T (x16) Anti-Vibration Pad
• U (x2) Cable Clips
• V (x2) Cable Management Cover
• S-A (x42) M5x16mm Screw
• S-B (x14) M6x11mm Screw
• S-C (x8) M6x35mm Screw
• S-D (x2) M8x16mm Screw
• T-A (x1) 2mm Allen Wrench
• T-B (x1) 5mm Allen Wrench

NOTE: Extras of some hardware included.

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury. Maximum capacity: 154lbs (70kg).

TOOLS NEEDED

• Drill
• Phillips Screwdriver

ASSEMBLY STEPS

STEP 1

Assemble Left Crossbar (F) to Left Leg (K) and Right Crossbar (G) to Right Leg (J) using M6x11mm Screws (S-B) and 5mm Allen Wrench (T-B).

[Diagram showing assembly of crossbars to legs]

STEP 2

Mount Left Side Bracket (L) to Left Leg (K) and Right Side Bracket (M) to Right Leg (J) using M6x11mm Screws (S-B) and 5mm Allen Wrench (T-B).

[Diagram showing mounting of side brackets to legs]

STEP 3

Connect Feet (S) to Right Leg (J) and Left Leg (K) using M6x35mm Screws (S-C) and 5mm Allen Wrench (T-B). Feet are installed offset, with the longer ends lining up with Side Brackets (L, M).

[Diagram showing connection of feet to legs]

STEP 4

Use Crossbar Connector (H) to connect Left Crossbar (F) and Right Crossbar (G) using M6x11mm Screws (S-B) and 5mm Allen Wrench (T-B).

[Diagram showing connection of crossbars with connector]

STEP 5

Flip assembly over. Loosen the knob on Sync Rod (D) and extend the hex shaft. Insert the hex shaft into Left Leg (K), making sure the metal retaining ring makes contact with the leg. While holding the hex shaft with one hand, extend Sync Rod (D) onto the spline shaft of Right Leg (J). Tighten the set screw on Sync Rod (D) using 2mm Allen Wrench (T-A). Retighten the knob.

[Diagram showing sync rod installation]

STEP 6

Insert Anti-Vibration Pads (T) into the frame assembly as shown below.

[Diagram showing placement of anti-vibration pads]

STEP 7

Assemble Left Panel (A), Middle Panel (B), and Right Panel (C) using Connecting Plates (E) with M5x16mm Screws (S-A), and a Phillips screwdriver.

[Diagram showing assembly of desktop panels]

STEP 8

Attach desk frame assembly to desktop assembly using M5x16mm Screws (S-A) and a Phillips screwdriver. Next, attach Shelf Brackets (P), Hooks (Q), and Control Panel (O) to desktop using M5x16mm Screws (S-A) and a Phillips screwdriver.

[Diagram showing attachment of frame to desktop and accessories]

STEP 9

Connect AC Adapter (N) and the cable from Right Leg (J) to Control Panel (O). Use Cable Clips (U) to manage cables.

[Diagram showing cable connections]

STEP 10

For added stability, Foot Extensions (R) can be added to the back of Feet (S). To do, remove the pads from the Feet (S), as shown below. Install Foot Extensions (R) with M8x16mm Screws (S-D) and 5mm Allen Wrench (T-B).

[Diagram showing installation of foot extensions]

STEP 11

Turn desk assembly over and hook Shelf (I) onto Shelf Brackets (P). Place Cable Management Covers (V) into desktop holes, as shown below.

[Diagram showing placement of shelf and cable management covers]

CAUTION!

• Do not exceed desk weight limit. [Weight Limit Symbol]
• Keep area of vertical motion free of obstacles. [Obstacle Free Symbol]
• Keep weight on desk balanced for correct operation and longer life of components. [Balanced Weight Symbol]
• Leave enough slack in cables to allow for full range of vertical motion. [Slack Cable Symbol]

Failure to follow these instructions may result in property damage and/or personal injury.