SKU: DESK-V123EB/EW

Scan the QR code or visit vivo-us.com/products/desk-v123eb for helpful videos and specifications.

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

Email: help@vivo-us.com

Website: www.vivo-us.com (Chat live with an agent!)

Phone: 309-278-5303

WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

ELECTRICAL SAFETY INSTRUCTIONS

This product is powered by electricity. To avoid burns, fire, and electric shock, please read the following instructions carefully:

• Do not clean the product while power is connected.
• Do not disassemble or replace components while power is connected.
• Never operate the system with a damaged cord or plug. Contact your seller to replace damaged parts.
• Never operate the system in damp environments or if any electrical components have made contact with liquids.
• Alterations of the power unit are not allowed.
• Outdoor use is prohibited.

WARNING: CHOKING HAZARD

Small parts - not for children under 3 years. Adult supervision is required.

PACKAGE CONTENTS

• A (x3) Feet
• B (x3) Motorized Leg
• C (x3) Side Bracket
• D (x1) Extension Connector
• E (x2) Outer Crossbar
• F (x3) Inner Crossbar
• G (x1) Crossbar With Plate
• H (x1) Outer Extension Crossbar
• I (x1) Inner Extension Crossbar
• J (x1) Controller
• K (x1) Control Unit
• L (x1) Power Cable
• M (x1) Short Extension Cable
• N (x1) Long Extension Cable
• O (x2) Tabletop Connector
• P (x18) Anti-Vibration Pad
• Q (x6) Cable Clip
• R (x6) Foot Pad
• S-A (x26) M5x16mm Screw
• S-B (x32) M6x14mm Screw
• S-C (x3) M8x12mm Screw
• S-D (x5) M5x16mm Screw
• S-E (x14) M6x35mm Screw
• T-A (x1) 5mm Allen Wrench

NOTE: Extras of each screw size have been included. Desktop not included. (2-section corner desktop shown only for reference)

TOOLS NEEDED

• Drill
• Phillips Screwdriver

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

Maximum Weight Capacity: 264 lbs (120 kg)

ASSEMBLY STEPS

STEP 1

Attach Feet (A) to the underside of Motorized Legs (B) using M6x35mm Screws (S-E) and 5mm Allen Wrench (T-A). Thread Foot Pads (R) into the underside of Feet (A).

Diagram showing feet attachment to motorized legs and foot pads being threaded in.

STEP 2

Connect Outer Crossbar (E) and Inner Crossbar (F) to one Motorized Leg (B) using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A).

Diagram showing crossbars connected to a motorized leg.

STEP 3

Connect Inner Crossbar (F) and Crossbar With Plate (G) to another Motorized Leg (B) using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A).

Diagram showing the second motorized leg with crossbars attached.

STEP 4

Slide crossbars from leg assemblies together. These will be secured in a later step. Secure Extension Connector (D) to the side of Crossbar With Plate (G) using M8x12mm Screws (S-C) and 5mm Allen Wrench (T-A).

Diagram showing crossbars sliding together and the extension connector being secured.

STEP 5

Connect Outer Extension Crossbar (H) and Inner Extension Crossbar (I) to Extension Connector (D) using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A).

Assemble Inner Crossbar (F) and Outer Crossbar (E) to the remaining Motorized Leg (B) using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A).

Slide crossbars of the third leg assembly onto the existing assembly to form a corner frame shape. These will be secured in a later step.

Diagrams showing the connection of extension crossbars and the final leg assembly.

STEP 6

Adjust frame to fit the desired desktop size and secure the following crossbars in place using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A): Crossbar With Plate (G), Outer Crossbars (E), and Outer Extension Crossbar (H).

Diagram showing frame adjustment and securing of crossbars.

STEP 7

Attach Side Brackets (C) to the outside edge of Motorized Legs (B) using M6x14mm Screws (S-B) and 5mm Allen Wrench (T-A).

Diagram showing side brackets attached to the motorized legs.

STEP 8

Attach Anti-Vibration Pads (P) to desktop mounting holes in the side brackets and crossbars.

Optional: If needed, use provided Tabletop Connectors (O) and M5x16mm Screws (S-A) to secure desktop pieces together. Note: Desktop is not provided.

Diagrams showing anti-vibration pads and optional tabletop connectors.

STEP 9

Place the assembled frame upside down on the desktop. Drill 10mm deep pilot holes using a 1/8" (3mm) drill bit, and secure using M5x16mm Screws (S-A) and a Phillips screwdriver.

Mark screw locations for Controller (J) and Control Unit (K), ensuring the controller cable can reach the box. Drill 10mm deep pilot holes using a 1/8" (3mm) drill bit. Mount Controller (J) and Control Unit (K) using M5x16mm Screws (S-D). Tighten all screws with a Phillips screwdriver.

Diagrams illustrating the placement and securing of the controller and control unit.

STEP 10

Connect cables from Controller (J) and Motorized Legs (B) to the Control Unit (K). If needed, use Extension Cables (M, N) to connect legs. Connect Power Cable (L) to Control Unit (K) and plug into an AC power outlet. Adjust Foot Pads (R) to sit level if necessary. Add Cable Clips (Q) as needed.

Diagrams showing cable connections and final setup.

CAUTION!

• Do not exceed desk weight limit. [Weight Limit Icon] 264 lbs (120 kg)
• Keep area of vertical motion free of obstacles. [Obstacle Icon]
• Keep weight on desk balanced for correct operation and longer life of components. [Balance Icon]
• Leave enough slack in cables to allow for full range of vertical motion. [Slack Icon]

Failure to follow these instructions may result in property damage and/or personal injury.