VIVO Black Electric Desk Riser

⚠️ WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

⚠️ CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

⚡ ELECTRICAL SAFETY INSTRUCTIONS

THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.

• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.

? PACKAGE CONTENTS

• A (x1) Desktop
• B (x2) Extended Feet
• C (x10) M5x10mm Screw
• D (x1) Keyboard Brackets
• E (x1) Cable Clip
• F (x2) Ziptie
• G (x1) Keyboard Tray
• H (x1) Power Cord

?️ TOOLS NEEDED

• Phillips Screwdriver
• Scissors

⚖️ DO NOT EXCEED WEIGHT CAPACITY

Failure to do so may result in serious injury.

Maximum Capacity: 33 lbs (15kg)

ASSEMBLY STEPS

STEP 1: Prepare the Desktop

Carefully remove the Desktop (A) from the packaging.

Illustration shows removing the desk unit from its box and placing it on a flat surface. A warning icon indicates potential pinch points with moving parts during lifting and lowering.

STEP 2: Attach Extended Feet

Flip the Desktop (A) upside down. Attach the Extended Feet (B) to the frame using M5x10mm Screws (C).

Illustration shows the underside of the desktop, with two extended feet being attached to the frame using screws.

STEP 3: Connect Power

Install the Power Cord (H). Plug the cord into the wall outlet and press the switch on the right side to raise the desktop.

Illustration shows the power cord connected to the desk and plugged into a wall outlet. A USB charging port is also indicated.

STEP 4: Mount Keyboard Tray Brackets

Mount the Keyboard Brackets (D) to the Keyboard Tray (G) using M5x10mm screws (C) and a Phillips screwdriver.

Illustration shows the keyboard tray with brackets being attached using screws and a screwdriver.

STEP 5: Attach Keyboard Tray

Hang the assembled keyboard tray onto the pre-installed knobs and tighten the knobs to secure. Ensure the Keyboard Brackets (D) are curving towards the user, not towards the inside of the desk.

Illustration shows the keyboard tray being attached to the desk mechanism via knobs. A close-up view highlights the correct orientation of the keyboard brackets.

STEP 6: Place Items on Desk

Place your monitor, laptop, and other items on the desk surface.

Illustration shows the assembled electric desk riser with a monitor and laptop placed on its surface.

STEP 7: Manage Cables with Clip

Attach the Cable Clip (E) to the underside of the Desktop (A) to help manage cables.

Illustration shows a cable clip being attached to the underside of the desk.

STEP 8: Secure Cables

Manage cables using Zip Ties (F).

Illustration shows cables being bundled together with zip ties for organization.

CAUTIONS

• Keep monitor and laptop base fully on the desktop. Illustration shows correct placement.
• Follow the cable routing instructions to avoid the potential to pinch cables. Illustration shows correct cable routing.
• Leave enough slack in cables to allow for the full range of vertical motion (15 inches / 38 cm). Illustration shows cables with adequate slack.
• Raise desktop slowly to keep items stable. Illustration shows the desk raising smoothly.

Failure to follow these instructions may result in property damage and/or personal injury.