Wolfang GA100 Action Camera User Manual
This manual provides comprehensive instructions for the Wolfang GA100 action camera.
Contents
Attention
Product Description
Package contents
Button Instructions
Preparation and Installation
Waterproof Case Open&Close
Dust-proof Cover Replacement
Battery Charging and Installation
SD Card Insertion and Formatting
Operation Instructions
Turn ON/OFF
Mode Operation Instructions
Settings Table
Wi-Fi/Computer/TV Connecting
Product Specifications
Warranty
Attention
- Keep the camera safe from falling and dropping.
- Keep the camera at a distance from strong magnetic interference objects like electrical machines to avoid strong radio waves that might damage the product and the quality of sound and image.
- Keep the camera away from water and liquids, unless equipped with a waterproof case. This may cause the malfunction of the camera.
- Keep the camera safe from children while charging. It takes about 3 hours to charge the battery. It is advised to take the battery out of the camera after use to avoid loss of battery power.
- For best results, use a high-quality Class 10 Micro SD Card (max support 64 GB). Please format the micro SD card on the camera before using and restart the camera after formatting.
- Do not expose the product directly to high temperatures over 45°C.
- Do not place heavy objects on the camera.
- To avoid data loss, please do not place your Micro SD card near strong magnets.
Product Description
Package Contents
The package includes the following items:
- Waterproof Case
- Dust-proof Cover
- USB Cable
- Two Batteries
- Frame
- Mount
- Long Thumbscrew
- Short Thumbscrew
- Extension Mount
- J-hook Mount
- 360° Rotating Screw
- Bicycle Mount
- Backpack Clip
- Adhesive Pads
- Flat Adhesive Pads
- Release Buckles
- Insurance Tether Strap
- Microphone
- Remote control
- Bandage
- Adapter 2
Button Instructions
The camera features several buttons and ports:
- Front/Top: OK/Shutter button, Power/Mode button, Lens.
- Side: TF card slot, USB port, HDMI port, External microphone interface, UP/Wi-Fi button, Down button, Display screen.
- Bottom: Battery Door Latch.
Preparation and Installation
Waterproof Case Open&Close
A. How to open the waterproof Case correctly:
- Push the switch to the right as indicated by the arrow.
- Pull up the buckle of the waterproof case.
- Open the back cover of the waterproof case.
B. How to close the waterproof Case correctly:
- Compress the back cover of the waterproof case as shown by arrow 1.
- Pull down the buckle and connect it to the back cover as shown by arrow 2.
- Pull down the buckle of the waterproof case as shown by arrow 3.
Dust-proof Cover Replacement
The camera case is supplied with two protective covers: one is waterproof, and the other is dust-proof. The dust-proof cover does NOT protect the camera from water ingress.
- The waterproof protective cover is for underwater, beach, dust, and other adverse environments.
- The dust-proof protective cover protects the camera against dust, enhances sound quality, and reduces wind noise during activities like riding or jogging.
Replacement Steps:
- Find the slot on the waterproof case as indicated by the red circled place in Step 1.
- Hold the case with your hands as shown in Step 2 picture, face the slot on the case front, and tear the waterproof back cover off.
- Find the dust-proof back cover in your accessories. It has two inter-spaces on the left and right side. Insert the lower half of the cover into the slot, then push the upper half into the slot as indicated in Step 4 until the whole back cover is totally installed.
Battery Charging and Installation
The battery and the camera are packaged separately. Ensure the battery is charged before inserting it into the camera and turning it on.
A. Battery Charging
- The dual USB battery charger is not included in the camera's accessories and may need to be purchased separately. Alternatively, you can charge the battery within the camera using the USB cable.
- Connect the charger with a USB cable to a power plug or computer. Charging via a computer may be slower due to lower power output from USB ports.
- Charging indicator: When the charger is on, a red light indicates charging. The light turns blue when the batteries are fully charged. When charging the camera directly, a red light appears and disappears when the battery is fully charged.
- Normal full charging time is about 3.5 hours. Do not overcharge the battery.
B. Battery Installation
- Locate the battery compartment on the camera. Open the battery cover by using your right thumb's fingernail to push the switch to the right (arrow 1). Then, lift the battery cover with your left thumb's fingernails (arrow 2).
- After inserting the battery, install the battery cover. The extended part of the battery cover should be inserted into the left side of the battery compartment first. Then, press the right half of the battery cover down into the battery compartment. Please notice the direction of the battery and battery cover.
SD Card Insertion and Formatting
A. SD Card Insertion and Out
- Find the Micro SD card slot in the camera and insert the card into the camera following the indicated direction, then push it inside.
- To remove the SD card: Press down the SD card until you hear an insertion sound; then the SD card will pop out with a pop sound.
B. SD Card Formatting
- Insert the SD card, turn off the camera, and then turn it on.
- Press any button, and the camera will display "Please insert SD Card". Press the power button 3-4 times to enter the menu mode.
- Find the "Format" setting item, select "SD card", and press the OK button to complete the format.
The camera supports regular brand SD cards, Class 10 or above, with capacities from 8GB to 64GB. Please ensure the quality of the SD card. You must format the SD card on the camera before using it.
Operation Instructions
The GA100 series offers four modes: Video Mode, Photo Mode, Playback Mode, and Settings Mode. The following describes the function instructions of each button under these modes.
Turn ON/OFF
- Extended press the [Power/MODE Button] to turn on the camera.
- Extended press the [Power/MODE Button] to turn off the camera.
Mode Operation Instructions
Turn the camera on and repeatedly press the Power/Mode Button to cycle through camera modes and settings. The modes appear in the following order: Video Mode, Photo Mode, Playback Mode, Settings Mode.
Example: The screen displays "1080P60fps" with a video icon for Video Mode. After pressing the button, it changes to "16M" with a photo icon for Photo Mode.
Video Playback: Displays video files with details like resolution and duration.
Photo Playback: Displays photo files with details like resolution and date.
Video Settings: Allows adjustment of Video Resolution, Looping Video, Time-Lapse Video, Slow Motion, and Audio Record.
Settings Table
Press the Power/Mode Button four times after powering on to enter the Settings Menu. Use the UP or Down Button to cycle through options and the Shutter/OK Button to select a desired option. Press the Power/Mode Button to cycle through Video setting, Photo setting, General setting, System setting, and Exit.
Video Setting
- Video Resolution: Options include 4K 30fps, 2.7K 30fps, 1080p 60fps, 1080p 30fps, 720p 120fps. The default resolution is 4K 30fps.
- EIS (Electronic Image Stabilization): Off/On. Choose to enable or disable the anti-shake feature.
- Looping Video: Off/1 Min./3 Min./5 Min. When enabled, the video will be segmented at the set time.
- Time-Lapse Video: Off/1 Sec./5 Sec./10 Sec./30 Sec./60 Sec. The video recorded will be compressed to the set time length. For example, capturing one frame per second and playing it back at 30 frames per second results in a 30x speed increase.
- Slow Motion: Off/1080P/720p.
- Audio Record: Off/On. Choose On to record audio in your video. The default setting is On.
Photo Setting
- Photo Resolution: Options include 20M, 16M, 12M, 8M. The default resolution is 20M.
- Time-Lapse Photo: Off/2 Sec./10 Sec. After pressing the Shutter/OK Button, the camera takes photos in 2 or 10 seconds.
- Burst Photo: Off/3 photos/5 photos. The default setting is Off. Press the Shutter/OK Button once to take multiple pictures in a row. When this setting is active, Time-Lapse Photo will be automatically turned off.
General Setting
- Volume: 0-10. Adjust the sound level for viewing videos and pressing buttons.
- Beep: Off/On. Choose to enable or disable the beep sound when pressing buttons.
- Exposure: -2.0 to +2.0. Adjust the exposure value when shooting to make the photo brightness more realistic.
- White Balance: Auto/daylight/cloudy/fluorescent/fluorescent 1/fluorescent 2/incandescent. Adjusting this setting helps correct photo colors under different lighting conditions.
- ISO: Auto/ISO100/ISO200/ISO400/ISO800/ISO1600/ISO3200. ISO refers to light sensitivity and affects image quality. A higher ISO typically results in a noisier or "grainy" image.
- Effect: Normal/Sepia/B&W/Negative. Change the color tone of the captured picture.
System Setting
- Car Mode: Off/On. When enabled, the camera functions as a dashcam. Looping video is automatically set to 3 minutes (adjustable), and recording starts automatically after power-on.
- Power Off: Off/1Min/5Min. The camera automatically shuts down after a set period of inactivity.
- Date & Time: Set the date and time (Y-M-D 00:00:00). Use the UP/Down Button to change values and the Shutter/OK Button to move to the next item. Tip: Since the camera does not have a built-in battery, the time resets to 2018/01/01 when power is lost or the battery is removed. You will need to reset the time when powering on.
- Stamp: Off/On. Enable or disable timestamps on photos and videos.
- Upside Down: Off/On. When enabled, the camera's screen flips upside down.
- Screen Saver: Off/30sec./1min./3min. If there is no operation for a set period, the screen will automatically go black. The camera does not turn off; any button press will light up the screen.
- Format: YES/NO. Formats the memory card in the camera. All data will be deleted. It is recommended to format the memory card before use.
- Reset: YES/NO. Restores all camera settings to default.
- Exit: Press the shutter button to exit the settings menu.
VIDEO MODE
Video:
A video icon will appear on the upper left corner of the camera screen. Ensure your video settings are configured. If the video icon is not displayed, press the Power/Mode Button repeatedly to access the setting menu and select the desired option in Video Setting (e.g., Looping Video, Time-lapse Video, Slow Motion).
- To Start Recording: Press the Shutter/OK Button. The camera's status light (Blue) on the left of the screen and a Red Dot on the screen will flash while recording. Tip: If the camera starts recording automatically after powering on, check if Car Mode is enabled.
- To Stop Recording: Press the Shutter/OK Button again. The camera status light (Blue) and the Red Dot on the screen will stop flashing, indicating recording has stopped.
- To Turn On/Off Audio Record: Press the Down Button. The MIC icon will show the status on the lower right corner of the screen.
- Time-Lapse Video: If Time-lapse video is enabled in Video settings, a clock icon will appear at the top of the camera screen. The number displayed on the icon indicates the video compression time you set.
Tips:
- The camera automatically stops recording when the battery is out of power. Your video will be saved before the camera powers off.
- The camera automatically stops recording when the SD card is full if the looping record function is turned off. Files will be overwritten in recording order when the SD card is full if the looping record function is turned on.
PHOTO MODE
Photo:
A photo icon will appear on the upper left corner of the camera screen. Please confirm that your photo settings are configured. If the photo icon is not displayed, press the Power/Mode Button repeatedly to access the setting menu and select the desired option in Photo Setting (e.g., Time-lapse Photo, Burst Photo).
- To capture a photo: Press the Shutter/OK Button. The camera will emit a shutter sound (ensure Volume in General Setting is turned on).
- Time Lapse Photo: If Time-lapse photo is enabled in Photo setting, a clock icon will appear at the top of the camera screen. The number displayed on the icon is the time interval for taking pictures.
- Burst Photo series: Press the Shutter/OK Button; the camera will continuously take the number of photos you have set. At this time, the time interval set in Time-Lapse Photo will become invalid.
PLAYBACK
Playback Videos and Photos:
Press the Power/Mode Button to switch the camera to Playback mode (Playback video and Playback photo). Press the UP/DOWN Button to cycle through videos or photos, and then press the Shutter/OK Button to playback the desired options.
- Delete files: In the file preview interface, press the UP button for seconds to select whether to delete the current file. While playing back videos, press the DOWN button to fast forward the video at 2/4/8X times, and press the UP button to rewind.
- To exit playback mode: Press the Power/Mode Button to return to the main preview menu, then press the Power/Mode Button again to switch to settings mode.
Tips: Due to different camera-supported file formats, files recorded on other cameras with the same memory card may not be playable on this camera.
Wi-Fi/Computer/TV Connecting
Wi-Fi CONNECTION
Connect to the Wi-Fi:
The Wi-Fi Application allows remote control of your camera via a smartphone or tablet. You can view videos or pictures and download recordings. The connection steps are as follows:
- Download the LIVE DV app on your smartphone or tablet from Google Play or the Apple App Store.
- Press the Up Button to turn on Wi-Fi after powering the camera ON. The status light (BLUE) on the top of the camera remains flashing while waiting for Wi-Fi connection and stays on when Wi-Fi is connected.
- Find and connect to the Wi-Fi in your phone's Wi-Fi list using the Wi-Fi name and password displayed on the camera.
- Open the LIVE DV App on your smartphone or tablet after the Wi-Fi is connected; the camera will be controlled by your phone.
Tips:
- Press and hold the Up Button again to turn off the Wi-Fi.
- The camera can only connect to one device at a time.
- Wi-Fi connection consumes power; please avoid connecting Wi-Fi when the battery power is low.
Computer Connecting
There are three options when connecting to a computer using the included micro-USB cable: MSDC, PC CAM, and Charging mode. Press the Up/Down button to switch between these modes and press the Shutter/OK Button to enter.
- MSDC: Access files stored on the camera's micro SD card to copy or view them on a computer. This function can also be achieved using a micro SD card reader.
- PC Camera: Use the camera as a webcam for video chats and video recording on your computer. You may need to allow Adobe Flash Player to run in your video chat software.
- Charging mode: The USB cable is used solely for charging. You can still use the camera in this mode.
TV Connecting
With HDMI output, you can display movies and images recorded by this camera on large screens like TVs or projectors.
- Turn off the camera.
- Connect the camera and TV with a commercially available Micro HDMI cable (NOT INCLUDED).
- Turn on the camera and enable the HDMI setting on the device you intend to connect to.
Tips:
- The HDMI input device should support 1080P.
- When outputting HDMI, the camera's display turns black. The screen is displayed on the HDMI input device, but operation is controlled via the camera.
Product Specifications
| Specification | Details |
|---|---|
| Model | GA100 |
| Sensor | Sony IMX179 |
| Lens | 170° Wide angle lens |
| Display dimension | 2 Inch LCD |
| Photo Resolution | 20M/16M/12M/8M |
| Video Format | H.264 code; MOV |
| Image Format | JPEG |
| Wi-Fi Connection | Android / iOS supported (5 Meter range) |
| Micro SD Card | Class 10, FAT 32, 8GB-64GB |
| EV (Exposure Value) | Auto(-2.0~2.0EV) |
| Ports | Micro USB / Micro HDMI / DC2.5 microphone |
| Charging Time | About 3 hours (5V/2A) |
| Waterproof Depth | 40M/131.2ft |
| Operating temperature | 0°C~45°C |
| Battery | Rechargeable 1050mAh Li-ion battery |
| After-sales Contact | support@wolfang.co |
Warranty
All WOLFANG products come with a limited warranty of 12 months from the date of purchase. Wolfang has a professional customer service team to provide support. For any questions or confusions regarding the product or warranty, please contact Wolfang via email. They will endeavor to respond within 24 hours to help resolve any issues.
Contact: support@wolfang.co
