Thermokon NOVOS 3 x LRW

Datasheet

Subject to technical alteration

Issue date: 21.07.2025 A143

NOTES ON DISPOSAL

The crossed-out wheelie bin symbol indicates that the product or removable batteries must not be disposed of with household or commercial waste. Within the EU, you are legally obliged to dispose of the product separately and appropriately in accordance with the national laws of your country. Alternatively, please contact your supplier or Thermokon Sensortechnik GmbH. Further information can be found at: www.thermokon.com

SECURITY ADVICE – CAUTION

The installation and assembly of electrical equipment should only be performed by authorized personnel.

The product should only be used for the intended application. Unauthorized modifications are prohibited! The product must not be used in relation with any equipment that in case of a failure may threaten, directly or indirectly, human health or life or result in danger to human beings, animals or assets. Ensure all power is disconnected before installing. Do not connect to live/operating equipment.

Please comply with:

• Local laws, health & safety regulations, technical standards and regulations
• Condition of the device at the time of installation, to ensure safe installation
• This data sheet and installation manual

MOUNTING ADVISE ROOM SENSORS

The accuracy of the room sensors are influenced by the technical specifications as well as the positioning and the installation type.

During Assembly:

• Seal mounting box (if present).
• Installation type, air draught, heat source, radiation heat or direct sunlight can affect the measurement.
• Building material specific properties of the installation place (brick-, concrete-, partition wall, cavity wall, ...) can affect the measurement.

Assembly not recommended in...

• Air draught (e.g.: close to windows / doors / fans ...)
• Near heating sources,
• Direct sunlight
• Niches / between furniture / ...

APPLICATION NOTICE FOR HUMIDITY SENSORS

At regular environmental conditions, it is recommended to calibrate the sensor annually to check the compliance with the accuracy required in the application. The following conditions can damage the sensor element or lead in long term to loss of the specified accuracy:

• Mechanical stress
• Contamination (e.g. dust / fingerprints)
• Aggressive chemicals
• Ambient conditions (e.g. condensation on measuring element)

Re-calibration or exchange of the sensor element are not subject of the general warranty.

i Do not touch the sensor elements!

INFORMATION ABOUT SELF-CALIBRATION FEATURE CO2

All gas sensors are subject to drift. The degree of drift is dependent on the use of components and product design. In addition, the following environmental conditions, among others, can accelerate/favor the aging and wear of the sensors:

• Mechanical stress (also due to temperature fluctuation)
• Contamination (dust / fingerprints e.g.)
• Abrasive chemicals
• Environmental influences (high humidity / condensation on measuring element)

An internal self-calibration function with dual channel technology compensates the caused drift. Thermokon sensors are for permanent use (e.g. hospitals).

INFORMATION ABOUT INDOOR AIR QUALITY CO2

EN 13779 defines several classes for indoor air quality:

TECHNICAL DATA

Enclosure

PC VO, pure white, design cover (optional)

Protection

IP20 according to DIN EN 60529

Ambient condition

-20..+70 °C, max. 85% rH non-condensing, with CO2 sensor operating temperature range 0..+50 °C

Mounting

Surface mounted on flush-mounting box (Ø=60 mm) or to be mounted flat onto the surface using screws, base part can be mounted and wired separately

Measuring values (type dependend)

Temperature | humidity | (CO2)

Power supply

1x AA Batterie 1,5-3,6V (Alkaline or Lithium)

Battery life

+/- 5 years (depending on device configuration, network setup, battery-type* and ambient conditions)

*3,6V Lithium battery (compared to 1,5V alkaline) recommended to increase battery life

Set point (P) (optional)

potentiometer

Button (T) (optional)

for presence detection

Temperature

Measuring range temperature: -20..+70 °C

Accuracy temperature: ±0,4K (typ. at 21 °C)

Humidity

Measuring range humidity: 0..100% rH

Accuracy humidity: ±2% between 30..70% rH (typ. at 21 °C)

CO2 (optional)

Measuring range CO2: 0..5000 ppm

Accuracy CO2: ±50 ppm +3% of reading (typ. at 21 °C, 50% rH, 1015 hPa)

OCC (type dependent)

Measuring variable: Movement

Detection range: Ø=5 m at approx. 2,5 m installation height (max. 5m)

Sensor: PIR (passive Infrared)

LoRaWAN®

Radio technology: LoRaWAN®

LoRaWAN version: 1.0.4

Device class: Class A

Frequency: EU868 (863-870 MHz)

Max. transmission power: +14 dBm (25 mW)

Receiver sensitivity: -137 dBm

Antenna: internal send- / receiver antenna

LoRaWAN Features

Over The Air Activation (OTAA), Adaptive Data Rate (ADR)

Data transmission (configurable): Heartbeat interval (default: 1440 min), Measurement interval (default: 1 min), hysteresis transmission behavior,

MOUNTING ADVICES

The installation can be performed on the flat wall surface or on a flush-mounted box. A representative place should be selected. Sunshine and draft, e.g. in the installation tube should be avoided, so that the measurement result is not falsified. Seal the end of the installation tube.

• For wiring, the upper part of the device must be removed from the base plate. Base plate and upper part are detachably connected to each other by means of locking lugs.
• The mounting of the base plate on the flat wall surface is done with rawplugs and screws.
• Finally, the device is attached to the base plate and fixed with the screw.

Housing open / close

BATTERY INSTALLATION

Position the battery as shown in the picture. (Observe battery polarity)

CONFIGURATION

The configuration is performed in powered state. The following options are available for configuring the device:

The configuration app with the corresponding instructions can be downloaded from the Google Play Store or the Apple App Store.

ADVICE FOR COMMISSIONING:

i The LoRaWAN credentials required for commissioning can be read out via the uConfig software or the LRWapp. On request, the LoRaWAN credentials can also be provided in digital form. For this purpose, please contact your respective contact person.

INFORMATION ABOUT LoRaWAN SPECIFICATION

The Thermokon LoRaWAN specification can be downloaded from our website.

CONFIGURATION

Application-specific reconfiguration of the devices can be carried out using the Thermokon LRWapp.

Press the button to start Bluetooth communication. After pressing the button, a connection can be established via the app within approx. 20 seconds. This is indicated by a flashing LED.

You can download the LRWapp from the Google Play Store or the Apple App Store.

FUNCTIONAL DESCRIPTION NOVOS OCC

The sensor lens divides the detection area in 32 measurement areas. The sensor detects changes in infrared radiation that occur when an object* (or person) moves that has a different IR temperature than its surroundings.

Object properties:

• Temperature difference (between object and environment) > +4°C
• Object-speed > 1,0 m/s
• Object-size > 700x250 mm

i The motion detector should not be mounted near disturbing heat sources (e.g. lamps, radiators, fans etc.) to avoid false alarms:

Fast temperature changes on the environment can trigger false alarms.

DETECTION RANGE (NOVOS 3-OCC)

Detection range: 5 m max.

Field of view horizontal: < 90° / 110°

Field of view vertical: < 90° / 110°

Detection zone: 32

An detection distance of 2,5 m results in a square detection zone of approx. 5 x 5 m, or a circular detection zone of approx. Ø 7 m divided in 32 measuring zones.

Formula: tan(field of view/2)*detection distance =Radius detection range

* The specified ranges refer to average conditions and are approximate values.

Function test

A function test ensures that a movement is located in the optical detection area of the sensor. Walk through the detection area after integrating the device in a LoRaWAN® Network and check whether a radio telegram was send.

DIMENSIONS (MM | IN.)

ACCESSORIES (SCOPE OF DELIVERY)

Battery (Alkaline 1,5V AA) Item-No.: 459099

ACCESSORIES (OPTIONAL)

• Rawplugs and screws (2 pcs. each) Item No.: 102209
• Mounting bracket (surface mounted) white Item No.: 795050
• Mounting bracket (surface mounted) black Item No.: 795074
• Battery ER14505 (Lithium Thionyl chloride 3,6V AA) Item No.: 759182