IKEA LAGAN FRÖSLUNDA Integrated Dishwasher

Important Safety Information

⚠️ Before proceeding with installation, read the safety information in the User Manual.

Tools and Parts Required

Tools:

• Phillips head screwdriver ?
• Flathead screwdriver ?
• Spirit level ?
• Tape measure ?
• Scissors ✂️
• Drill ?️
• Work gloves ?
• Hammer ?

Parts List:

Installation Steps

1. Step 1: Attach Trim Piece

   Attach the trim piece (J) to the top front edge of the dishwasher appliance. The piece slides into place.

2. Step 2: Prepare Countertop Adhesive Tape

   Apply the adhesive tape (I) to the underside of the countertop. Measure the required length (approximately 600mm) and cut the tape. The tape is applied to create a seal.

3. Step 3: Position Appliance and Adjust Leveling Feet

   Slide the dishwasher appliance into the cabinet opening. Ensure it is correctly aligned. Adjust the leveling feet using a screwdriver to raise or lower the appliance until it is level. Close-up views show the adjustment mechanism for the feet (UP/DOWN) and the water/drainage connections at the bottom front.

4. Step 4: Measure and Mark Countertop

   Measure and mark the countertop for drilling. The countertop must support a weight between 2.5Kg (5.5lb) and 7.5KG (16.5lb).

5. Step 5: Apply Template to Countertop

   Prepare the template (H) by folding it as indicated. Apply the adhesive tape (I) to the back of the template. Position the template on the underside of the countertop, aligning it with the edges and pre-marked points.

6. Step 6: Secure Template

   Secure the template (H) to the underside of the countertop using 16 screws (A) and a Phillips head screwdriver (PH2).

7. Step 7: Drill Holes

   Drill 16 holes into the countertop using a 2 mm (5/64") drill bit. The drilling depth should be 5mm.

8. Step 8: Attach Mounting Brackets

   Attach the mounting brackets (D, E) to the underside of the countertop using screws (A). A diagram shows drilling a hole into a cabinet side panel and inserting a screw.

9. Step 9: Connect Appliance to Cabinet

   Connect the appliance to the cabinet. A warning symbol indicates caution regarding electrical components. Ensure proper alignment.

10. Step 10: Attach Front Panel

    Attach the appliance's front panel. Use screws (A) and (B) to secure it. Close-up views show the attachment points and mechanism.

11. Step 11: Final Positioning and Sealing

    Ensure the appliance is correctly positioned within the cabinet. A 50mm clearance is indicated at the bottom front edge.

12. Step 12: Adjust Leveling and Connect Hoses

    Adjust the appliance's leveling feet again if necessary. Connect the water supply and drainage hoses at the bottom front of the appliance. Diagrams show the connection points and adjustment directions.

13. Step 13: Secure Appliance to Cabinet

    Secure the appliance to the cabinet using screws (C). Close-up views illustrate the locking mechanism for securing the appliance.

14. Step 14: Final Checks

    Perform final checks on alignment and door closure. Diagrams show correct and incorrect alignment of cabinet doors.

15. Step 15: Attach Internal Mounting Plates

    Attach internal mounting plates to the appliance using screws (A) and (B).

16. Step 16: Connect Internal Components

    Connect internal wiring and hoses. A screwdriver is shown with symbols indicating adjustment points.

17. Step 17: Connect Water Supply

    Connect the water supply hose to the water inlet. Ensure the water pressure is between 0.3-10 bar. Use the provided 3/4" to 1/2" adapter (F) if necessary. A warning symbol indicates the importance of proper electrical grounding.

18. Step 18: Connect Drainage Hose

    Connect the drainage hose to the drain pipe. Ensure the hose does not exceed a maximum length of 100 cm. Secure the hose connection using the clamp (G).

Dimensions and Clearances

Cabinet Dimensions:

• Height: 840mm - 880mm
• Width: 550mm
• Depth: 448mm

Appliance Dimensions:

• Height: 835mm - 875mm
• Depth: 450mm
• Front Clearance: 120mm
• Bottom Clearance: 45mm

⚠️ A minimum clearance of 450mm is required.