Schneider Electric Modicon M221 Logic Controller, 40 IO, Relay (TM221C40R)

Specifications

Product or Component Type: Modicon M221 Logic controller

Range of Product: Modicon M221

[Us] rated supply voltage: 100...240 V AC

Discrete input number: 24, discrete input IEC 61131-2 Type 1

Analogue input number: 2

Analogue input voltage: 0...10 V

Discrete output type: Relay normally open

Discrete output number: 16 relay

Discrete output voltage: 5...125 V DC / 5...250 V AC

Discrete output current: 2 A

Complementary

Discrete I/O number: 40

Maximum number of I/O expansion module: 7 (local I/O-Architecture), 14 (remote I/O-Architecture)

Supply voltage limits: 85...264 V

Network Frequency: 50/60 Hz

Inrush current: 40 A

Maximum power consumption in VA: 67 VA (100...240 V with max number of I/O expansion module), 37 VA (100...240 V without I/O expansion module)

Power supply output current: 0.52 A (5 V expansion bus), 0.24 A (24 V expansion bus)

Discrete input logic: Sink or source (positive/negative)

Discrete input voltage: 24 V DC

Discrete input voltage type: DC

Analogue input resolution: 10 bits

LSB value: 10 mV

Conversion time: 1 ms per channel + 1 controller cycle time analog input

Permitted overload on inputs: +/- 30 V DC (5 min maximum) analog input, +/- 13 V DC (permanent) analog input

Voltage state 1 guaranteed: >= 15 V input

Voltage state 0 guaranteed: <= 5 V input

Discrete input current: 7 mA (discrete input), 5 mA (fast input)

Input impedance: 3.4 kOhm (discrete input), 100 kOhm (analog input), 4.9 kOhm (fast input)

Response time: 35 µs turn-off, 12...15 µs input; 10 ms turn-on output; 10 ms turn-off output; 5 µs turn-on (10, 11, 16, 17 fast input), 35 µs turn-on (other terminals input); 5 µs turn-off (10, 11, 16, 17 fast input), 100 µs turn-off (other terminals input)

Configurable filtering time: 0 ms input, 3 ms input, 12 ms input

Output voltage limits: 125 V DC, 277 V AC

Maximum current per output common: 7 A

Absolute accuracy error: +/-1% of full scale analog input

Electrical durability: 100,000 cycles AC-12 (120 V, 240 VA, resistive), 100,000 cycles AC-12 (240 V, 480 VA, resistive), 300,000 cycles AC-12 (120 V, 80 VA, resistive), 300,000 cycles AC-12 (240 V, 160 VA, resistive), 100,000 cycles AC-15 (cos phi = 0.35, 120 V, 60 VA, inductive), 100,000 cycles AC-15 (cos phi = 0.35, 240 V, 120 VA, inductive), 300,000 cycles AC-15 (cos phi = 0.35, 120 V, 18 VA, inductive), 300,000 cycles AC-15 (cos phi = 0.35, 240 V, 36 VA, inductive), 100,000 cycles AC-14 (cos phi = 0.7, 120 V, 120 VA, inductive), 100,000 cycles AC-14 (cos phi = 0.7, 240 V, 240 VA, inductive), 300,000 cycles AC-14 (cos phi = 0.7, 120 V, 36 VA, inductive), 300,000 cycles AC-14 (cos phi = 0.7, 240 V, 72 VA, inductive), 100,000 cycles DC-12 (24 V, 48 W, resistive), 300,000 cycles DC-12 (24 V, 16 W, resistive), 100,000 cycles DC-13 (24 V, 24 W, inductive (L/R = 7 ms)), 300,000 cycles DC-13 (24 V, 7.2 W, inductive (L/R = 7 ms))

Switching frequency: 20 switching operations/minute with maximum load

Mechanical durability: 20,000,000 cycles relay output

Minimum load: 1 mA (5 V DC relay output)

Protection type: Without protection (5 A)

Reset time: 1 s

Memory capacity: 256 kB user application and data RAM, 10000 instructions; 256 kB internal variables RAM; 256 kB built-in flash memory backup of application and data

Data backed up: 256 kB built-in flash memory backup of application and data

Data storage equipment: 2 GB SD card (optional)

Battery type: BR2032 or CR2032X lithium non-rechargeable

Backup time: 1 year (at 77 °F (25 °C) by interruption of power supply)

Execution time for 1 KInstruction: 0.3 ms (event and periodic task)

Execution time per instruction: 0.2 µs (Boolean)

Exct time for event task: 60 µs (response time)

Maximum size of object areas: 512 %M memory bits, 512 %KW constant words, 8000 %MW memory words, 255 %C counters, 255 %TM timers

Realtime clock: With

Clock drift: <= 30 s/month (at 77 °F (25 °C))

Regulation loop: Adjustable PID regulator up to 14 simultaneous loops

Counting input number: 4 fast input (HSC mode) 100 kHz 32 bits

Connections and Schema

Integrated connection type: USB port mini B USB 2.0, Non-isolated serial link serial 1 RJ45 RS485, Non-isolated serial link serial 2 RJ45 RS232/RS485

Supply: Serial link supply 5 V, <200 mA

Transmission rate: 1.2...115.2 kbit/s (115.2 kbit/s by default) (49.2 ft (15 m) RS485), 1.2...115.2 kbit/s (115.2 kbit/s by default) (9.8 ft (3 m) RS232), 480 Mbit/s USB

Communication port protocol: USB port USB - SoMachine-Network, Non-isolated serial link Modbus master/slave - RTU/ASCII or SoMachine-Network

Local signalling: 1 LED (green) for PWR, 1 LED (green) for RUN, 1 LED (red) for module error (ERR), 1 LED (green) for SD card access (SD), 1 LED (red) for BAT, 1 LED (green) for SL1, 1 LED (green) for SL2, 1 LED per channel (green) for I/O state

Electrical connection: Removable screw terminal block for inputs, Removable screw terminal block for outputs, Terminal block (3 for connecting the 24 V DC power supply), Connector (4 for analogue inputs), Mini B USB 2.0 connector for a programming terminal

Maximum cable distance between devices: Shielded cable <32.8 ft (10 m) fast input, Unshielded cable <98.4 ft (30 m) output, Unshielded cable <98.4 ft (30 m) digital input, Unshielded cable <3.3 ft (1 m) analog input

Insulation: Between input and internal logic 500 V AC, Non-insulated between analogue input and internal logic, Non-insulated between analogue inputs, Between supply and ground 1500 V AC, Between sensor power supply and ground 500 V AC, Between input and ground 500 V AC, Between output and ground 1500 V AC, Between supply and internal logic 2300 V AC, Between sensor power supply and internal logic 500 V AC, Between output and internal logic 2300 V AC, Between Ethernet terminal and internal logic 500 V AC, Between supply and sensor power supply 2300 V AC

Marking: CE, cULus, EAC, UKCA, cULus HazLoc

Sensor power supply: 24 V DC 250 mA supplied by the controller

Mounting support: Top hat type TH35-15 rail IEC 60715, Top hat type TH35-7.5 rail IEC 60715, Plate or panel with fixing kit

Height: 3.5 in (90 mm)

Depth: 2.8 in (70 mm)

Width: 6.3 in (160 mm)

Product Weight: 1.005 lb(US) (0.456 kg)

Environment

Standards: IEC 61131-2, UL 508, CAN/CSA C22.2 No. 213, IACS E10, ANSI/ISA 12-12-01

Environmental characteristic: Ordinary and hazardous location

Resistance to electrostatic discharge: 8 kV in air IEC 61000-4-2, 4 kV on contact IEC 61000-4-2

Resistance to electromagnetic fields: 9.1 V/m (10 V/m) 80 MHz...1 GHz IEC 61000-4-3, 2.7 V/m (3 V/m) 1.4 GHz...2 GHz IEC 61000-4-3, 0.9 V/m (1 V/m) 2...2.7 GHz IEC 61000-4-3

Resistance to magnetic fields: 98.4 A/m (30 A/m) 50/60 Hz IEC 61000-4-8

Resistance to fast transients: 2 kV IEC 61000-4-4 (power lines), 2 kV IEC 61000-4-4 (relay output), 1 kV IEC 61000-4-4 (I/O), 1 kV IEC 61000-4-4 (Ethernet line), 1 kV IEC 61000-4-4 (serial link)

Surge withstand: 2 kV power lines (AC) common mode IEC 61000-4-5, 2 kV relay output common mode IEC 61000-4-5, 1 kV I/O common mode IEC 61000-4-5, 1 kV shielded cable common mode IEC 61000-4-5, 0.5 kV power lines (DC) differential mode IEC 61000-4-5, 1 kV power lines (AC) differential mode IEC 61000-4-5, 1 kV relay output differential mode IEC 61000-4-5, 0.5 kV power lines (DC) common mode IEC 61000-4-5

Resistance to conducted disturbances: 10 V (0.15...80 MHz) IEC 61000-4-6, 3 V (0.1...80 MHz) Marine specification (LR, ABS, DNV, GL), 10 V spot frequency (2, 3, 4, 6.2, 8.2, 12.6, 16.5, 18.8, 22, 25 MHz) Marine specification (LR, ABS, DNV, GL)

Electromagnetic emission: Conducted emissions 79 dBμV/m QP/66 dBμV/m AV power lines (AC) 0.15...0.5 MHz IEC 55011, Conducted emissions 73 dBμV/m QP/60 dBuV/m AV power lines (AC) 0.5...300 MHz IEC 55011, Conducted emissions 120...69 dBμV/m QP power lines 10...150 kHz IEC 55011, Conducted emissions 63 dBμV/m QP power lines 1.5...30 MHz IEC 55011, Radiated emissions 40 dBμV/m QP class A 10 m 30...230 MHz IEC 55011, Conducted emissions 79...63 dBμV/m QP power lines 150...1500 kHz IEC 55011, Radiated emissions 47 dBμV/m QP class A 10 m 200...1000 MHz IEC 55011

Immunity to microbreaks: 10 ms

Ambient air temperature for operation: 14...131 °F (-10...55 °C) horizontal installation, 14...95 °F (-10...35 °C) vertical installation

Ambient Air Temperature for Storage: -13...158 °F (-25...70 °C)

Relative humidity: 10...95%, without condensation in operation, 10...95%, without condensation in storage

IP degree of protection: IP20 with protective cover in place

Pollution degree: 2

Operating altitude: 0...6561.68 ft (0...2000 m)

Storage altitude: 0...9842.5 ft (0...3000 m)

Vibration resistance: 3.5 mm 5...8.4 Hz symmetrical rail, 3.5 mm 5...8.4 Hz panel mounting, 1 gn 8.4...150 Hz symmetrical rail, 1 gn 8.4...150 Hz panel mounting

Shock resistance: 98 m/s² 11 ms

Product Certifications

RCM, LR, cULus, DNV-GL, ABS, EAC, CE, UKCA, cULus HazLoc

Packing Units

Unit Type of Package 1: PCE

Number of Units in Package 1: 1

Package 1 Height: 4.30 in (10.92 cm)

Package 1 Width: 5.70 in (14.48 cm)

Package 1 Length: 8.30 in (21.08 cm)

Package 1 Weight: 30.0 oz (850 g)

Unit Type of Package 2: CAR

Number of Units in Package 2: 12

Package 2 Height: 11.57 in (29.4 cm)

Package 2 Width: 15.55 in (39.5 cm)

Package 2 Length: 21.93 in (55.7 cm)

Package 2 Weight: 24.297 lb(US) (11.021 kg)

Unit Type of Package 3: P12

Number of Units in Package 3: 144

Package 3 Height: 41.34 in (105.0 cm)

Package 3 Width: 47.24 in (120.0 cm)

Package 3 Length: 31.50 in (80.0 cm)

Package 3 Weight: 321.9 lb(US) (146 kg)

Environmental Data

Schneider Electric aims to achieve Net Zero status by 2050 through supply chain partnerships, lower impact materials, and circularity via our ongoing "Use Better, Use Longer, Use Again" campaign to extend product lifetimes and recyclability.

Environmental footprint: Carbon footprint (kg CO2 eq, Total Life cycle): 115

Materials and Substances: Packaging made with recycled cardboard: Yes, Packaging without single use plastic: Yes

EU RoHS Directive: Pro-active compliance (Product out of EU RoHS legal scope)

REACH Regulation: REACH Declaration

California proposition 65: WARNING: This product can expose you to chemicals including: Lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

PVC free: Yes

Repack and remanufacture: End of Life Information

Take-back: No

WEEE: The product must be disposed on European Union markets following specific waste collection and never end up in rubbish bins.

Dimensions Drawings

Dimensions:

mm: 75.9 (2.99), 163 (6.42), 103.6 (4.08)

in.: 75.9 (2.99), 163 (6.42), 103.6 (4.08)

Mounting and Clearance

Mounting on a Rail

Correct Mounting Position: [Image of correct mounting position]

Acceptable Mounting Position: [Image of acceptable mounting position]

Incorrect Mounting Position: [Image of incorrect mounting position]

Direct Mounting on a Panel Surface

(1) Install a mounting strip

[Image of direct mounting on a panel surface]

Mounting Hole Layout

Dimensions: M4 x 6/8 mm (0.24/0.31 in.)

Layout: [Diagram showing mounting hole layout with dimensions]

Clearance

[Diagram showing required clearance around the unit]

Connections and Schema

Digital Inputs

Wiring Diagram (Positive Logic): [Diagram of positive logic wiring for digital inputs]

(*) Type T fuse

Wiring Diagram (Negative Logic): [Diagram of negative logic wiring for digital inputs]

(*) Type T fuse

Connection of the Fast Inputs: [Diagram showing connection of fast inputs]

Inputs: 10, 11, 16, 17

Relay Outputs

Negative Logic (Sink): [Diagram of negative logic (sink) relay outputs]

(1) The COMO, COM1, COM2 and COM3 terminals are not connected internally.

(2) To improve the life time of the contacts, and to protect from potential inductive load damage, you must connect a free wheeling diode in parallel to each inductive DC load or an RC snubber in parallel of each inductive AC load.

Sink wiring (negative logic): [Diagram illustrating sink wiring]

Positive Logic (Source): [Diagram of positive logic (source) relay outputs]

(1) The COMO, COM1, COM2 and COM3 terminals are not connected internally.

(2) To improve the life time of the contacts, and to protect from potential inductive load damage, you must connect a free wheeling diode in parallel to each inductive DC load or an RC snubber in parallel of each inductive AC load.

Source wiring (positive logic): [Diagram illustrating source wiring]

Analog Inputs

[Image showing analog input connection]

Input Terminals: 0 V AN1, 0 V AND

Voltage: 0...10 V

The (-) poles are connected internally.

Pinout:

USB Mini-B Connection

[Diagram showing USB Mini-B connection with cables and lengths]

Cable 1: TCSXCNAMUM3P (3 m/9.8 ft)

Cable 2: BMXXCAUSBH018 (1.8 m/5.9 ft)

SL1 Connection

[Diagram of SL1 RJ45 connector pinout]

N.C.: not connected

*: 5 Vdc delivered by the controller. Do not connect.

[Diagram showing SL1 connection to DCE and DTE devices via RJ45 and SUB D 9 pin connectors]

SL2 Connection

[Diagram of SL2 RJ45 connector pinout]

N.C.: not connected

Performance Curves

Derating Curves

Embedded Digital Inputs (No Cartridge)

[Graph showing derating curve for embedded digital inputs without cartridge]

X: Ambient temperature

Y: Input simultaneous ON ratio

Embedded Digital Inputs (with Cartridge)

[Graph showing derating curve for embedded digital inputs with cartridge]

X: Ambient temperature

Y: Input simultaneous ON ratio