Operating Manual For Easy Clicker UR2-211

1 Introduction

This remote control is designed to operate most Digital, Analog Cable boxes, IPTV set top boxes and TVs.

2 Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

1. Remove the battery compartment cover from the back of your remote control.
2. Check battery polarity carefully, and install the batteries as shown in the illustration below. [Illustration: Two AA alkaline batteries should be inserted with correct polarity.]
3. Replace the battery compartment cover.

3 Button Functions

Description of the remote control layout and button functions:

• TV, CBL: Used to select the Device you want to operate and signals remote control activity.
• ALL OFF: Designed to send Power On/Off commands for up to two Components with one button press.
• SETTINGS/MENU: Displays the settings menu.
• OK/SEL: Selects highlighted screen options.
• INFO: Displays information about the program currently playing or highlighted in the program guide.
• EXIT: Exit from current screen.
• A, B, C, D: Make direct selections from on-screen menus.
• INPUT: Selects the video source from available video components.
• VOL +/-: Raises or lowers the sound level.
• MUTE: Silences the audio. Press to activate. Press this key again to restore sound to previous level.
• CH +/-: Selects the next higher or lower channel.
• PAGE +/-: Accesses pages above or below the information currently displayed.
• LANGUAGE: Change the language.
• FAV: Displays favorite channel.
• NUMBER Pad: Enter numbers to tune to channels. Also make numeric entries on on-screen menus. You can also use the CH +/- and the guide as alternate ways to tune to channels.
• Macro Button: For future use.

4 Programming the Remote Control

When instructed to press a [DEVICE] button, press either the CBL or TV button, depending on which device you are programming the remote to operate.

A. Quick Set-Up Method

Refer to the Section B Quick Set-up table of codes.

1. Turn on the component you want to program (e.g., your TV).
2. Press and hold the [DEVICE] key for 5 seconds until the Device LED blinks once and stays on. Continue to hold the [DEVICE] key and press the number key assigned to your brand in the Quick Setup Code Table. Release both [DEVICE] key and the number key to save the code. The Device LED will blink twice to confirm that the code is stored.
3. Point the remote control at the component.
4. Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all components (CBL, TV).

B. Quick Set-up Code Tables

These tables provide quick setup codes for various brands.

CBL Quick Set-up Codes:

• 0: PACE DTA
• 1: SA/CISCO, SAMSUNG, PACE DIGITAL
• 2: MOTOROLA DIGITAL
• 3: MOTOROLA DTA
• 4: EVOLUTION DTA
• 5: CISCO IPTV
• 6: ADB IPTV
• 7: TECHNICOLOR
• 8: AMINO 140/540 IPTV
• 9: MOTOROLA IPTV

TV Quick Set-up Codes:

• 0: SANYO
• 1: SONY
• 2: SAMSUNG
• 3: LG
• 4: TOSHIBA
• 5: PANASONIC
• 6: PHILIPS
• 7: HITACHI
• 8: SHARP
• 9: VIZIO

C. Manual Programming

Program the remote by entering a three-digit code number corresponding to your equipment's brand and model.

1. Turn on the equipment (Cable Box or TV).
2. Press and hold the [DEVICE] button and the [OK/SEL] button simultaneously for 3 seconds. The corresponding device LED will turn on, indicating it's ready for programming (stays on for 30 seconds).
3. Point the remote control at the equipment and enter the three-digit code number for your brand from the code tables. If multiple codes exist for your brand, try them one by one until the equipment turns off.
4. Verify the code by pressing the [POWER] button. The equipment should turn back on. Test other functions (volume, mute) to ensure correct operation. If not, repeat from step 3 with the next code.
5. Store the code by pressing the same [DEVICE] button again. The device LED will blink twice to confirm.

D. Auto Search Method

Use this method if manual codes don't work or your brand isn't listed.

1. Turn on the equipment (Cable Box or TV).
2. Press and hold the [DEVICE] button and the [OK/SEL] button simultaneously for 3 seconds. The device LED will turn on (stays on for 30 seconds).
3. Press the [CH] or [CH] button repeatedly or hold it down. The remote will send Power ON/OFF code signals. Release the button as soon as the equipment turns off.
4. Verify the code by pressing the [POWER] button. The equipment should turn back on. Test other functions. If not, repeat from step 3 to continue searching.
5. Press the same [DEVICE] button to store the code. The device LED will blink twice to confirm.

E. Programming the All Off Button

Program the [ALL OFF] button to send up to two power On/Off commands with a single press.

1. Press the [CBL] button.
2. Press the [ALL OFF] button and the [OK/SEL] button simultaneously for 3 seconds. The [CBL] button LED will turn on for 30 seconds.
3. Press the first [Device] button you want to store in the [ALL OFF] button, then press the [POWER] button. Repeat for other devices.
4. Press the [CH5] button to save the power commands. The [CBL] button LED will blink twice to confirm.

F. Programming Volume Control

By default, VOL+/- and MUTE control the TV. To control another device:

1. Press the [OK/SEL] button and [CBL] button simultaneously for 3 seconds. The device LED will turn on (stays on for 30 seconds).
2. Press the [VOL+] button. The device LED will blink.
3. Press the [DEVICE] button corresponding to the device you want volume/mute to control. The device LED will blink twice to confirm. (To control Cable Box, press [CBL] in this step).

G. Programming Channel Control

By default, CH5/CH6 control the Cable Box. To control another device:

1. Press the [OK/SEL] button and [CBL] button simultaneously for 3 seconds. The device LED will turn on (stays on for 30 seconds).
2. Press the [VOL-] button. The device LED will blink.
3. Press the [TV] button. The device LED will blink twice to confirm. (To control Cable Box, press [CBL] in this step).

H. Memory Lock System

This remote control is designed to retain programmed memory for 10 years, even after batteries are removed.

For additional information, visit www.universalremote.com.

5 Setup Code Tables

The manual provides extensive setup code tables for various brands of Cable Boxes (CBL), Cable Converters, IPTV devices, and TVs. These tables list specific three-digit codes required for manual programming. Due to the extensive nature of these tables, they are not fully transcribed here. Please refer to the original manual or the manufacturer's website for complete lists.

Example Code Entries:

CBL-CABLE Converters:

• 0: PACE DTA
• 1: SA/CISCO, SAMSUNG, PACE DIGITAL
• 2: MOTOROLA DIGITAL
• 3: MOTOROLA DTA
• 4: EVOLUTION DTA
• 5: CISCO IPTV
• 6: ADB IPTV
• 7: TECHNICOLOR
• 8: AMINO 140/540 IPTV
• 9: MOTOROLA IPTV

TV:

• SAMSUNG: 192, 184, 185, 004, 101, 127, 133, 160, 089, 105, 070, 237, 239, 461, 578, 655
• SONY: 001, 608, 651, 126, 139, 236, 240, 241, 602
• LG: 004, 569, 106, 112, 127, 247, 250, 598, 698, 648, 741
• HITACHI: 011, 004, 613, 007, 009, 072, 010, 012, 023, 075, 127, 158, 236, 238, 587, 614, 749

Note: For the most up-to-date and complete code lists, please consult the official Universal Remote website.