JENSEN JWM62A Mobile Audio System

Introduction

Thank you for choosing a Jensen product. This manual provides clear and easy-to-follow instructions to help you use all the features of your new Jensen receiver for maximum enjoyment.

Features

• Digital AM/FM Tuner with 30 Preset stations (12 AM/18 FM)
• Bluetooth Ready with A2DP/AVRCP Streaming Audio
• APP Ready
• Electronic Bass, Treble, Balance and Fader Controls
• Skip Protected Disc Mechanism
• DVD/CD-R/RW and MP3 Compatible
• Time/Alarm Clock
• LCD Backlight Control
• 1/8" Front Auxiliary Audio/Video Input
• Rear Audio RCA Inputs/Outputs
• USB Playback of MP3/WMA Files
• 3 Zone / 8 Speaker Output
• Wireless Remote Control Included

Precautions

• Proper Power Supply: Designed for a 12-volt DC, negative ground battery system (standard in North American vehicles).
• Disc Mechanism: Avoid inserting foreign objects into the disc slot to prevent malfunction.
• Service: Do not attempt to disassemble or adjust the unit; contact a professional for assistance.
• Moisture: Do not expose the equipment to rain or moisture to reduce the risk of fire or electric shock.
• Cleaning: Clean the front of the unit with a slightly damp cloth only. Do not use cleansers.
• Accessories: Use only recommended accessories to reduce the risk of fire, electric shock, or interference.

Caution: Laser Product

This mobile DVD player is a Class I laser product. Use as instructed to avoid hazardous radiation exposure. Do not open covers or attempt self-repair.

Packing List

The package includes: JWM62A unit, Remote Control, 20-PIN Speaker Wire, AUX AUDIO/VIDEO CABLE.

Installation

Read all instructions before beginning installation. It is recommended to have your Jensen JWM62A installed by a reputable RV dealership.

Tools and Supplies Needed:

• Phillips screwdriver
• Wire cutters and strippers
• Tools to remove existing radio (e.g., screwdriver, socket wrench)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 16 gauge wire for power connections
• 16-18 gauge speaker wire
• Four M3x20mm screws

Disconnecting the Battery

To prevent a short circuit, turn off the ignition and remove the negative (-) battery cable before installation. Note: If the vehicle has an on-board drive or navigation computer, do not disconnect the battery cable, as this may cause loss of computer memory. Exercise extra caution to avoid short circuits.

Selecting the Mounting Location

Choose a location that avoids:

• Heat-radiating appliances (e.g., electric heaters)
• Equipment that radiates heat
• Poorly-ventilated or dusty areas
• Moist or humid locations

Preparing the Opening

Use the following diagram to measure and cut a mounting hole. Mount the unit using four M3x20mm screws.

Mounting Hole Diagram Dimensions:

• Overall Width: 9.76 inches (± 0.6 inches)
• Overall Height: 6.11 inches (± 0.6 inches)
• Inner Width (approximate): 9.30 inches (± 0.6 inches)
• Inner Height (approximate): 4.68 inches (± 0.6 inches)
• Screw Hole Placement: 0.19 inches (± 0.6 inches) from edges, 4 places.

Note: Before cutting, ensure the area behind the mounting location is clear of wires, fuel, and vacuum or brake lines.

Wiring

The wiring diagram illustrates all connections required for proper operation. Any unused speaker wires must have their exposed ends cut off or insulated individually.

Wiring Diagram Description

The diagram shows the main wiring harness connector (20-PIN) and its connections to various components including the amplifier remote, switched +12V, ground, and speaker outputs for Zones A, B, and C (Front Left/Right, Rear Left/Right). It also shows connections for AM/FM antenna, Audio Input, and Audio/Video Output.

Wiring Connections Table:

Basic Operation

Power

Press the POWER button (3) to turn the unit on or enter standby mode. The unit resumes the last mode (Tuner, Aux, etc.) upon turning on.

Volume Control

Rotate the VOL encoder knob (13) clockwise to increase or counter-clockwise to decrease volume. The maximum volume is 40. The LCD displays the numerical level during adjustment.

Audio Menu Setting

Press the AUDIO button (31) to cycle through audio adjustment options. Rotate the VOL/ENTER encoder knob (13) to adjust the selected feature:

• BAS: Bass level from -7 to +7.
• TRE: Treble level from -7 to +7.
• BAL: Speaker balance between Left (L7) and Right (R7). BAL 0 is equal balance.
• FAD: Speaker fade between Rear (R7) and Front (F7). FAD 0 is equal balance.

Loudness

Press the LOUD button (32) to toggle the loudness function on/off.

Mute

Press the MUTE button (34) to silence audio output. Press again to restore the previous volume level.

Liquid Crystal Display (LCD)

The LCD panel (1) displays frequency, time, and activated functions. Use the BRIGHT UP button to increase and BRIGHT DOWN button to decrease LCD brightness from LEVEL 0 (off) to LEVEL 9 (brightest).

Note: LCD visibility may decrease in cold temperatures but will return to normal as temperature increases.

System Menu Setting

1. Press the SETTING button (29) to enter the system menu.
2. Use the SETTING button or the |<< (6) or >>| (35) buttons to navigate the menu list.
3. Rotate the volume encoder knob to adjust the selected option. Changes are saved automatically after 6 seconds of inactivity or by pressing the ENTER knob button.

Adjustable items include:

• Beep On/Off: Toggles audible beeps for button presses. (Does not affect alarm clock tones).
• LCD Brightness: Adjusts LCD backlight from BRI 0 (off) to BRI 9 (brightest).
• Region: Sets frequency spacing for USA/Europe.

Bluetooth Settings

• Bluetooth On/Off: Enables or disables Bluetooth.
• Bluetooth Device: View, lock, unlock, disconnect, connect, or delete paired devices.
• Bluetooth Pair: Initiates pairing mode.
• PRESET Volume (PVOL): Selects an automatic turn-on volume.

Reset

Press the ENTER knob button to reset the JWM62A to factory default settings.

Tuner Operation

Select a Band

1. Press the AM button (17) repeatedly to select AM1 or AM2.
2. Press the FM button (18) repeatedly to select FM1, FM2, or FM3.

Manual Tuning

Press the >>| or |<< buttons (35, 6) to seek stations up or down step by step.

Auto Seek Tuning

Press and hold the >>| or |<< buttons (35, 6) to automatically seek the next or previous strong station.

Preset Stations

Six numbered preset buttons store and recall stations for each AM and FM band.

Store a Station

Select a band (if needed). Press a 1-6 preset button to store the current station.

Automatically Store / Preset Scan (AS/PS)

• Automatically Store: Select an AM or FM band. Press and hold the AS/PS button (30) for over 3 seconds to scan and store the 12 or 18 strongest stations. Press AS/PS again to stop.
• Preset Scan: Select a band. Press AS/PS to scan stored stations. The unit pauses for 10 seconds at each station. Press AS/PS again to stop scanning.

Disc Operation

Track Select

Press the >>| or |<< buttons (35, 6) to advance to the next or previous track. Press and hold for fast forward/reverse.

Fast Forward/Reverse

Press and hold >>| or |<< buttons (35, 6) or use remote buttons (14) for FORWARD x2. Press and hold additional times for FORWARD x4, x8, x20, or PLAY. Press the II button (33) to end fast forward/reverse and resume normal playback.

Repeat (RPT)

Press the 4/ button (10) during disc play to access repeat functions: RPT OFF, RPT ONE (repeat track), RPT ALL (repeat disc).

Random Shuffle (RDM)

Press the 3/ button (9) during disc play to play all tracks in random order (RDM ON). Press again to stop random play (RDM OFF).

Programmed Playback

1. Press the PROG button (7) on the remote control to access the programmed playback screen.
2. Use the cursor buttons (15) on the remote control to access fields.
3. Use number buttons to enter track numbers.
4. Press the /|| button (17) or highlight "PLAY" and press ENTER (5) to begin playback in the programmed order. Use "CLEAR" to delete the list. Press PROG to exit.

Inserting a CD

Insert a CD label-side up into the disc slot (15); playback begins automatically.

Ejecting a CD

Press the EJECT button (27) to stop CD play and eject the disc.

Pausing Playback

Press the II button (33) to suspend or resume disc play.

Stop Playback

Press the 1/■ button (7) to suspend play. "PRE STOP" appears. Press the II button (33) to resume. Press the 1/■ button twice to "STOP" playback.

DVD/VCD Operation

Inserting a Disc

Insert a disc label-side up into the disc slot (15); playback begins automatically. Press the DISC (20) or USB (24) button to switch between USB and DVD sources.

Ejecting a DVD

Press the EJECT button (27) to stop DVD play and eject the disc.

Pausing Playback

Press the II button (33) to suspend or resume disc play.

Stop Playback

Press the 1/■ button (7) to suspend play. "PRE STOP" appears. Press the II button (33) to resume. Press the 1/■ button twice to "STOP" playback.

Track Select

Press the >>| or |<< buttons (35, 6) to advance to the next or previous track. The selected track number will appear on the display.

Enter/Select

In menu mode, press the ENTER button to select a menu option.

Language Selection

While playing a DVD, press the 6/FOLDER UP button (11) to change the DVD audio language.

Fast Forward/Reverse

Press and hold >>| or |<< buttons (35, 6) or use remote buttons (17) for FORWARD x2. Press and hold additional times for FORWARD x4, x8, x20, or PLAY. Press the II button (33) to end fast forward/reverse and resume normal playback.

Repeat Chapter/Title

Press the 4/ button (10) or RPT button (21) on the remote control multiple times during playback to select repeat options: RER1 (track), RER ALL (disc), RPT OFF for VCD; Chapter, Title, RPT ALL, RPT OFF for DVD.

Playback Control (VCD Only)

Press the MENU button (14) on the remote control to turn Playback Control on/off.

Programmed Playback

1. Press the PROG button (7) on the remote control to access the programmed playback screen.
2. Use the cursor buttons (15) on the remote control to access fields.
3. Use number buttons to enter track numbers.
4. Press the /|| button (17) or highlight "PLAY" and press ENTER (5) to begin playback in the programmed order. Use "CLEAR" to delete the list. Press PROG to exit.

DVD Playback Features

Features available during DVD playback include:

• LANG: Select alternate audio language.
• SUBTITLE: Select alternate subtitle language.
• ANGLE: Select alternate viewing angle.
• ZOOM: Zoom the picture (ZOOM 2, 3, 4, 1/2, 1/3, 1/4) or return to normal view.

Note: Feature availability depends on DVD embedded information.

Playback Information

Press the button (26) on the remote control to display playback information. This includes media playing and current playback time. Press repeatedly to view elapsed/remaining time for tracks and discs, audio language (e.g., 1/5 ENG), sound format (e.g., 5.1 CH), and subtitle language (e.g., 1/4 ENG).

VCD Playback Information

The display shows track number, playback time, and repeat status (OFF, 1, D, A). Press the button repeatedly to view elapsed/remaining time.

Remote Control Direct Track Entry

Use the number pad on the remote control (10) to select a track directly. For single digit entries, press the number. For two-digit entries, press 10+ followed by the last digit (e.g., for track 16, press 10+ then 6).

GOTO Direct Track/Chapter Access

Use the GOTO button (25) to access a track (chapter) directly. Enter the 3-digit track number and press ENTER (5) to begin playback.

MP3/USB Operation

Insert/Eject Disc

Insert a disc label-side up into the disc slot (15) for playback. Press the eject button (27) to stop playback and eject the disc.

Insert/Remove USB Device

Locate the USB interface connector (20) on the front of the radio. Insert the USB device to access USB mode and begin playback. The LCD will display "LOADING". To remove the USB device, press the FM/AM, DISC, USB, or AUX button to change modes, then remove the device. Note: MP4 video format is not supported. USB input supplies up to 1A of charging current.

Play/Pause

Press the II button (33) to suspend or resume disc play.

Track Select

Press the >>| or |<< buttons (35, 6) to access the previous/next file. The selected file number will appear on the display.

Folder Up/Down

Press and hold the 6/FD UP button (12) to access a higher folder level (FOLDER UP). Press and hold the 5/FD DW button (11) to access a lower folder level (FOLDER DN).

Repeat (RPT)

Press the 4/ button (10) or RPT button (20) on the remote control multiple times during playback to select from repeat options: RPT 1 (track), RPT DIR (folder), RPT ALL (disc), RPT OFF.

Random Shuffle (RDM)

Press the 3/ button (9) during disc play to play all files in random, shuffled order (RDM ON). Press again to stop random play (RDM OFF).

Programmed Playback

1. Press the PROG button (7) on the remote control to access the programmed playback screen.
2. Use the cursor buttons (15) on the remote control to access fields.
3. Use number buttons to enter track numbers.
4. Press the /|| button (17) or highlight "PLAY" and press ENTER (5) to begin playback in the programmed order. Use "CLEAR" to delete the list. Press PROG to exit.

GOTO Direct Track/Chapter Access

Use the GOTO button (25) on the remote control to access a track (chapter) directly. Enter the 3-digit track number and press ENTER (5) to begin playback.

MP3 Playback Information

The display shows track number, file type, and playback time. It also indicates repeat status (OFF, 1, D). Press the button repeatedly to view elapsed/remaining playing time for the disc and current track.

Remote Control Direct Track Entry

Use the number pad on the remote control (9) to select a file directly. For single digit entries, press the number. For two-digit entries, press 10+ followed by the last digit (e.g., for file 16, press 10+ then 6).

Bluetooth Operation

The JWM62A features built-in Bluetooth technology for streaming audio playback.

About Bluetooth Technology

Bluetooth is a short-range wireless radio protocol operating in the 2.4 GHz range, transmitting audio and data at speeds up to 2.1 Mbit/s over a range of up to 10 meters.

Bluetooth Menu Options

Press and hold the BT button (22) to enter menu adjustment mode. Use >>| (35) or |<< (6) buttons, or the SETTING button, to access "Bluetooth On/Off". Rotate the volume encoder knob to select BLUETOOTH ON, then press ENTER to enable the function. Menu options available in Bluetooth mode include:

• Bluetooth Pair <ENTER>: Initiates pairing with a Bluetooth enabled device.
• Bluetooth Device: View a list of previously paired devices. Use >>|/|<< buttons to navigate. Press ENTER to select a device, then use >>|/|<< to choose Locked/Unlocked, Connect/Disconnect, or Delete.
• DISCONNECT: Temporarily disconnects a paired device.
• LOCKED/UNLOCKED: Locks devices to prevent them from being bumped from the list when more than 5 devices are paired.
• DELETE: Removes a device from the list.

Pairing a Bluetooth Device

Ensure the device to be paired is ready.

1. Press the BT button (22) to enter Bluetooth mode.
2. Press and hold the BT button (22) for about 4 seconds to start pairing. The JWM62A will display "PAIR" for 120 seconds.
3. On your device's Bluetooth settings, select "JWM62A" to begin connection.
4. A six-digit confirmation code will appear on both your device and the JWM62A. Confirm the code matches, then press "Pair"/"Confirm"/"Accept" on your device and press ENTER on the JWM62A to finish pairing. If codes do not match, press back (<) on the JWM62A to cancel.

After successful connection, you can listen to music from your Bluetooth enabled device.

Answering a Call

When answering a call, BT AUDIO will pause. It may resume automatically or require pressing the play button after the call ends.

Bluetooth Audio (A2DP)

Access A2DP music from Bluetooth enabled phones when connected. Press the BT button (22) to enter Bluetooth mode. "BT PAUSE" will display on the LCD.

Selecting Tracks

During playback, press the >>| or |<< buttons (35, 6) to play the previous or next track.

Pausing Playback

Press the II button (33) to pause Bluetooth audio playback. "BT PAUSE" will appear. Press II again to resume.

Note: If a Bluetooth device is disconnected (e.g., power off), the unit will automatically search for the matching phone when power is restored.

APP Operation

The JENSEN® Specialty Controller (jControl app) transforms your mobile device into a functional stereo remote control for the JWM62A.

Features

The app controls primary functions including:

• Power on/off
• Volume and mute
• CD/DVD player controls
• AM/FM radio tuner functions
• Bluetooth® streaming audio
• USB file structure visibility and track selection
• Auxiliary audio input control
• Speaker selection (A, B, C)
• Audio menu controls (bass, treble, balance, fader, equalizer, volume)
• Clock settings (sleep time, alarm)
• Visual display feedback (artist, title, album)

Connecting and using jControl app

After downloading and installing the jControl app, pair your device to the JWM62A as described for Bluetooth pairing. For Android devices, close the app before Bluetooth pairing to avoid connection errors.

Remote Control Operation

The remote control provides access to various functions across different modes (Tuner, Bluetooth, CD/MP3/USB, DVD).

Remote Control Button Functions:

DVD Setup Menu

Press the SETUP button (10) on the remote control to access the SETUP menu and adjust system settings.

System Setup

Controls include:

• TV System: Select AUTO, NTSC, or PAL.
• Screen Saver: Turn On/Off.
• TV Type: Select 4:3PS, 4:3 LB, or 16:9.
• Password: Set a four-digit security code.
• Rating: Set parental control level (requires password).
• Default: Restore default settings.

Language Setup

Controls language settings:

• OSD LANGUAGE: English, German, Spanish, French.
• Audio Language: English, Japanese, French, Spanish, Portuguese, Latin, German.
• Subtitle Language: English, French, Spanish, Portuguese, German, or OFF.
• Menu Language: English, French, Spanish, Portuguese, German.

Audio Setup

Controls audio output:

• Audio Out: Defines the digital output format.
• Key: Changes the audio output key.

Video Setup

Controls video settings:

• Brightness
• Contrast
• Hue
• Saturation
• Sharpness

Digital Setup

Controls speaker settings:

• OP Mode: Select LINE OUT or RF REMOD.
• Dynamic Range: Select FULL, 6/8, 4/8, 2/8, or OFF.
• Dual Mono: Select STEREO, MONO/L, MONO/R, or MIX MONO.

Care and Maintenance

Keep the product dry. If it gets wet, wipe it dry immediately. Liquids may contain minerals that can corrode electronic circuits.

Keep the product away from dust and dirt, which can cause premature wear.

Handle the product gently and carefully. Dropping it can damage circuit boards and cases.

Wipe the product with a dampened cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents.

Use and store the product only in normal temperature environments. High temperatures can shorten the life of electronic devices and damage parts.

Ignition Noise

Ignition systems are a common source of radio reception noise. This noise varies with engine speed. It can often be suppressed by using a radio suppression type high voltage ignition wire and suppressor resistor. Additional noise suppressors may also be used.

Interference

Radio reception in a moving environment differs from stationary reception. AM reception can be affected by bridges or high voltage lines. AM signals can travel great distances due to atmospheric reflection.

Troubleshooting

Specifications

FM Tuner

• Frequency Coverage (USA): 87.5 to 107.9 MHz
• Frequency Coverage (Europe): 87.5 to 108 MHz
• Sensitivity: <4 μV
• Stereo Separation@1 kHz: >25 dB

AM Tuner

• Frequency Range (USA): 530-1710 kHz
• Frequency Range (Europe): 522-1620 kHz
• Sensitivity (S/N=20dB): <63 μV

Amplifier

• Output Power: 6W x 8
• Output Impedance: Compatible with 4-8 Ω speakers, 4 ohm load minimum.

DVD

• Frequency Response: 20-20,000 Hz
• Channel Separation: 50 dB
• S/N Ratio: 65 dB
• Distortion: 0.5%

General

• Power Supply Requirements: DC 12 Volts, Negative Ground
• Operating Voltage: 11-16 VDC
• Overall Dimensions: 265.0mm (W) x 178.0mm (D) x 172.0mm (H) (10.4" W x 7.0" D x 6.77" H)
• Mounting Dimensions: 236.2mm (W) x 155.2mm (D) x 73.6mm (H) (9.3" W x 6.11" D x 5.12" H)
• Weight: 1.45 KG (3.20 lbs)

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment complied with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.