Whirlpool 400020026436 Built-in Dishwasher Installation Guide

This guide provides detailed, step-by-step instructions for the proper installation of your Whirlpool built-in dishwasher model 400020026436.

Included Parts and Required Tools

Parts Included:

A: Instruction Manual (1x)
B: Mounting Bracket (1x)
C: Cover Plate (1x)
D: Hinge Plate (4x)
E: Screw ⌀3.5x25 mm (16x)
F: Screw ⌀3x16 mm (8x)
G: Hinge (Left) (1x)
H: Hinge (Right) (1x)
I: Screw ⌀3.5x12 mm (8x)
J: Alignment Tool (2x)
K: Allen Key (1x)
L: Screw ⌀3.5x18 mm (4x)
M: Screw ⌀3x16 mm (2x)
N: Soundproofing Material (1x)
O: Sliding Rail (1x)

Tools Required:

1: Pencil
2: Scissors ✂️
3: Adhesive Tape ?
4: Phillips Screwdriver
5: Phillips Screwdriver
6: Adjustment Tool
7: Pliers ?️
8: Level ?
9: Measuring Tape
10: Drill ड्रिल️
Safety Gloves ?
Safety Glasses ?

Specifications and Dimensions

Appliance Specifications:

Noise Level: 38/39/40 dB

Sliding Rail (O) Length: 585 mm

Cabinet Requirements:

Standard Cabinet Width: 60 cm

Cabinet Height Range: 820 - 900 mm

Minimum Cabinet Depth: 560 mm

Minimum Base Clearance: 600 mm

Dishwasher Unit Width: 598 mm

Dishwasher Unit Depth: 555 mm

Dishwasher Unit Height: Adjustable within 820 - 900 mm range

Door Panel Weight Capacity:

For 600 mm wide cabinets: 9 - 15 kg

For 750 mm wide cabinets: 9 - 10 kg

Electrical and Water Connections

Electrical Requirements:

Ensure a properly grounded electrical outlet is accessible. Consult local electrical codes for compliance.

Water Supply Requirements:

Minimum Water Pressure: 0.05 MPa / 0.5 Bar
Maximum Water Pressure: 1 MPa / 10 Bar

Drainage Requirements:

Connect the drain hose to a suitable waste outlet. Minimum drain hose diameter: 25 mm.

Approximate hose lengths required for connection: ~1300 mm, ~1500 mm, ~1500 mm.

Water inlet hose connection point: Minimum 400 mm, Maximum 800 mm from the floor.

Installation Procedure

Step 1: Unpacking and Inspection

⚠️ Carefully unpack the dishwasher. Inspect all components for any signs of damage. Verify that all listed parts are present before proceeding.

Step 2: Initial Placement and Checks

Position the dishwasher in its intended location. Confirm the cabinet dimensions meet the requirements (minimum depth 560 mm, minimum clearance 600 mm). Check the noise level rating (38/39/40 dB) and sliding rail length (585 mm). ℹ️ Ensure the cabinet configuration is correct (✔️) and avoid incorrect configurations (❌).

Step 3: Measuring and Marking

Using the measuring tape (9) and pencil (1), accurately mark the positions for mounting hardware on both the appliance door panel and the cabinet structure as indicated in the diagrams.

Step 4: Preparing the Decorative Door Panel

Take the decorative door panel (A). Use scissors (2) ✂️ to cut out any templates or guide markings provided on the panel or accompanying material.

Step 5: Securing Templates

Apply adhesive tape (3) ? to secure the cut-out templates or markings onto the appliance door panel. This ensures precise alignment for subsequent drilling.

Step 6: Drilling Pilot Holes

Utilize the drill (10) ड्रिल️ and a Phillips screwdriver (4) to create pilot holes at the marked locations on the appliance door panel. ⚠️ Exercise caution to ensure the drilling depth does not exceed 10 mm. Do not drill too deep.

Step 7: Attaching Brackets to Door

Attach the hinge plates (D) to the appliance door panel using the appropriate screws (e.g., E, F). Use the Phillips screwdriver (4) or drill (10) ड्रिल️. ⚠️ Maintain a maximum drilling depth of 10 mm.

Step 8: Attaching Hinges to Cabinet

Attach the hinge plates (D) to the cabinet frame. Use screws (e.g., E, F) and the Phillips screwdriver (5). Ensure correct alignment and secure fastening.

Step 9: Mounting Main Hinges

Connect the main hinges (G, H) to both the appliance body and the door panel. Secure them using screws (I) and the Phillips screwdriver (5).

Step 10: Initial Door Adjustment

Use the Phillips screwdriver (5) to make initial adjustments to the door hinges. ⚠️ Ensure the door panel does not interfere with the cabinet structure, maintaining a clearance of at least 2 mm.

Step 11a: Installing Decorative Door Panel

Slide the decorative door panel onto the appliance. Connect it to the hinge mechanism. Use screws (e.g., 4) and the drill (10) ड्रिल️ or screwdriver as depicted.

Step 11b: Securing Decorative Door Panel

Ensure the decorative door panel is correctly attached and aligned with the appliance door. Secure it as shown in the diagrams.

Step 12: Engaging Locking Mechanism

Activate the locking mechanism on the hinges to firmly secure the door panel. The locking mechanism can be rotated 360 degrees. ⚠️ Confirm that the lock ? is fully engaged for safety and stability.

Step 13: Fine-Tuning Door Alignment

Use the adjustment screws on the hinges to fine-tune the alignment and spacing of the door panel. ℹ️ Follow the directional arrows in the diagrams to adjust the door horizontally and vertically for a perfect fit.

Step 14: Mounting and Leveling

Secure the appliance within the cabinet using appropriate mounting hardware. Use tools such as the level (8) ?, pliers (7) ?️, and adjustment tool (6) to ensure the dishwasher is perfectly level and stable. The door is designed to open up to 60 degrees. ⚠️ Ensure the door does not extend beyond the cabinet by more than 80 mm when fully opened.

Step 15: Final Adjustments and Checks

Perform final adjustments to the door's height and alignment. ℹ️ Maintain a minimum gap of 2 mm between the door and the cabinet frame. ⚠️ Adjust the door's vertical position within a maximum range of 4 mm for optimal appearance and function.

Step 16: Handling Door During Installation

⚠️ Handle the door panel with care throughout the installation process. Ensure all hinge connections and locking mechanisms are properly secured.

Step 17: Inserting Soundproofing Material

Insert the soundproofing material (N) into the designated channels or slots on the inner side of the door panel. Ensure it is seated correctly to provide optimal sound dampening.

Step 18: Final Appliance Placement

Carefully slide the installed dishwasher unit into its final position under the countertop.

Step 19a: Attaching Decorative Panel (Variant A)

Attach the decorative door panel to the appliance door using screws (L). Use the Phillips screwdriver (5). Ensure the panel is aligned correctly and securely fastened.

Step 19b: Attaching Decorative Panel (Variant B)