GuliKit ES PRO Controller User Manual

Controller Overview

USB-C Port: For charging and wired connection.

Indicator Light:

• Orange: Charging
• Green: Fully charged
• Flashing: Pairing
• Solid White: No custom settings
• Solid Blue: Custom settings enabled

Home Button: Press to turn on. Hold to turn off.

Settings Button: Used for special function configurations.

Pairing Button: Hold to pair.

Controller Mode Selector: Switch between different device modes.

Power Button: The controller automatically turns off after 15 minutes of inactivity. It does not turn off during USB connection or in Auto-Fire mode.

⚠️ CAUTION!

This product contains small parts (buttons, joystick caps, screws) that can cause choking if swallowed by children.

Calibration

Joystick Calibration

With the controller on, simultaneously hold the L, R, Left D-Pad, and B buttons for 6 seconds to enter calibration mode. During calibration, move the left and right analog sticks completely in full circles 2-3 times. Upon completion, the controller will vibrate once to indicate automatic exit from calibration mode.

Gyroscope Calibration

When the controller is on, place it on a flat surface. Simultaneously press the "+", "-", Left D-Pad, and B buttons. This will automatically start gyroscope calibration. Upon completion, the controller will vibrate once to indicate it.

Note: If the gyroscope is functioning normally, calibration is not necessary.

Pairing Methods

Pairing with PC

Bluetooth Pairing (730Hz Polling Rate)

1. Set the controller to PC mode.
2. Hold the pairing button for 2 seconds until the indicator light flashes rapidly, indicating pairing has started.
3. Access your computer's Bluetooth settings, search for available devices, and add the device named "GuliKit XW Controller".
4. The interface will display "Connected" to the new controller, indicating pairing is complete.

Wired Connection (1000Hz Polling Rate)

1. Set the controller to PC mode.
2. Connect one end of the USB-C to USB-A data cable to the controller.
3. Plug the other end into a USB-A port on your computer. For desktop computers, using USB ports on the back of the case is recommended for a more stable connection.

Android Pairing

1. Set the controller to PC mode.
2. Hold the pairing button for 2 seconds until the indicator light flashes rapidly.
3. In your phone's Bluetooth settings, search for and add "GuliKit XW Controller".
4. The screen will display "Connected" when finished.

Pairing with Switch / Switch 2

1. Set the controller to NS mode, turn it on, and hold the pairing button for 2 seconds. The indicator light will flash rapidly, indicating the start of pairing.
2. When the Switch / Switch 2 is in black screen mode (standby), press the HOME button on the Joy-Con to wake it up. It will then proceed to the controller pairing interface.
3. The interface will display that a new controller is connected, indicating pairing is complete.

Special Function Configurations

To configure special functions: Hold the Settings button, then press the corresponding key. All special settings are saved automatically.

Indicator Light Status: Blue: special settings enabled. White: no special configuration.

Low Battery: The indicator light flashes, and the vibration function automatically deactivates. When the battery level returns to normal, the vibration function reactivates automatically.

Reset

Long vibration feedback: Full factory reset.

Joystick Dead Zone

Single vibration feedback: Dead zone enabled.

Long vibration feedback: Dead zone disabled (default).

Continuous Fire (Turbo Fire) Setting

Single vibration feedback: Manual Turbo Mode - Continuous fire is activated by holding the button and stops when released.

Two vibration feedbacks: Auto Turbo Mode - Press the button once to start continuous fire, press again to stop.

Long vibration feedback: Disables manual and auto Turbo modes (default).

A-B / X-Y Swap

Single vibration feedback: Swaps A-B and X-Y button functions.

Long vibration feedback: Returns to default settings.

Adjust Vibration Intensity

Single vibration feedback: Low vibration.

Two vibration feedbacks: Standard vibration (default).

Three vibration feedbacks: High vibration.

Long vibration feedback: Disable vibration.

Adjust Analog Stick Sensitivity

Single vibration feedback: 50% sensitivity.

Two vibration feedbacks: 100% sensitivity (default).

Three vibration feedbacks: 150% sensitivity.

Note: R3 and L3 refer to the buttons activated when pressing down on the analog sticks. Each stick can be configured individually.

Configure 4 Directions on D-Pad

Single vibration feedback: The D-pad switches to 4-direction mode.

Long vibration feedback: Restores default 8-direction mode (default).

Adjust Motion Aim Assist for FPS on PC

Single vibration feedback: Low sensitivity aim assist.

Two vibration feedbacks: Medium sensitivity aim assist.

Three vibration feedbacks: High sensitivity aim assist.

Long vibration feedback: Disables motion aim assist (default).

Additional Controls:

• + L: Enables motion assist when the L button is held in-game.
• + ZL: Enables motion assist when the ZL trigger is held in-game.

Support

For more questions and answers, visit the website and navigate to the 'Support' section to find 'Frequently Asked Questions' (FAQ) related to the controller.