GuliKit Elves 2 Pro User Manual

Charging Indicator

During charging, the charging indicator light will be orange, and when fully charged, it will be green.

Calibration

Gyroscope Calibration

In the power-on state, with the controller placed on a flat surface, simultaneously press the '+', '-', D-pad Left, and A buttons. This will initiate an automatic calibration of the gyroscope. Once the calibration is complete, the controller will vibrate once as a notification. Calibration is not necessary if the gyroscope is functioning normally.

Joystick Calibration

Simultaneously press the 'L', 'R', D-pad Left, and 'A' buttons on the controller for 6 seconds while it is in the power-on state. During calibration, fully move the left and right joysticks in complete circles for 2 to 3 times. Once the calibration is complete, the controller will vibrate once as notification and will automatically exit the calibration mode.

Controller Features

• USB-C Port: Used for charging & wired connection.
• Pairing button: Initiates pairing mode.
• Controller status indicator light: Shows connection status.
• Mode button: Switches between different modes.
• OFF button: Powers off the controller.

The controller will automatically power off after 15 minutes of inactivity. To power on the controller, press any of the following buttons: A, B, X, Y, or Home button.

Note: The controller will not power off when using the full-auto Continuous Fire or replay function (Auto Pilot Gaming).

Pairing Methods

PC Pairing

Bluetooth Pairing (170Hz Polling Rate)

1. Switch the controller to Bluetooth mode. Long-press the pairing button for 2 seconds; the indicator light will blink quickly.
2. On your computer, go to Bluetooth settings, search for devices, and add the "GuliKit Controller".
3. The interface will display "Connected" when pairing is complete.

Wired Connection (1000Hz Polling Rate)

1. Set the controller to wired mode.
2. Connect one end of the provided data cable to the controller and the other end to a USB-A port on your computer. For desktop computers, use a rear USB port for a more stable connection.

Android, iOS, and macOS Pairing

1. Switch the controller to the appropriate mode (e.g., iOS mode).
2. Long-press the pairing button for 2 seconds; the indicator light will blink quickly.
3. On your device, go to Bluetooth settings, search for devices, and add the "Xbox Wireless Controller".
4. The interface will display "Connected" when pairing is complete.

Nintendo Switch Pairing

Method 1: Wireless Pairing

1. On the Switch, navigate to the controller settings page.
2. Set the controller to Switch mode. Long-press the pairing button for 2 seconds; the indicator light will blink quickly.
3. The Switch interface will display a connection to the new controller.

Method 2: Wired Pairing

1. Set the controller to Switch mode.
2. Connect one end of the provided data cable to the controller and the other end to a USB-A port on the Switch dock.
3. Place the Switch console on the dock. The controller will automatically pair.
4. Once paired, you can unplug the data cable for wireless use or leave it plugged in for wired mode.

Auto Pilot Gaming (APG) Function

The APG function allows for recording and playback of custom commands or macros using the APG button (Double-Square icon button).

Recording Process

1. Hold the APG button for 3 seconds. A short vibration indicates recording has started.
2. All subsequent button presses and joystick movements will be recorded.
3. To stop recording, press the APG button again or wait for it to automatically stop after 10 minutes. A long vibration indicates the recording is complete. The maximum recording time is 10 minutes.

Replaying Recorded Actions

• Press the APG button once briefly to repeat the recorded actions once.
• Double-click the APG button to continuously repeat actions until interrupted.
• During replay, you can use the joystick for movement.
• To cancel a replay midway, press any button except the joysticks.

Special Function Settings

All special function settings require holding down the Setting button (Gear icon button) while pressing the corresponding buttons for configuration. Settings are automatically saved. The logo light will be blue when special settings are configured and white when they are not.

When the battery is low, the logo light will flash, and the vibration function will automatically turn off. Vibration will resume when the battery level is restored.

Motion Aim Assist (PC FPS Games)

• + L, ZL: Set Motion Aim Assist.
• + L: Motion assist activates when the 'L' button is held.
• + ZL: Motion assist activates when the 'ZL' trigger is held.
• Vibration Feedback: One vibration for low sensitivity, two for medium, three for high. Long vibration disables motion aim assist (default).

Joystick Dead Zone Mode

• + (Joystick): Set Dead Zone Mode.
• Vibration Feedback: One vibration for Dead Zone On mode, long vibration for Dead Zone Off mode (default).

Adjust Joystick Sensitivity

• + R3, L3: Adjust Joystick Sensitivity.
• Vibration Feedback: One vibration for 50% sensitivity (red ring), two for 100% (blue ring, default), three for 150% (green ring). R3 and L3 refer to pressing down on the joysticks. Each joystick can be configured individually.

4-Direction D-pad

• + (D-pad): Set 4-direction on D-pad.
• Vibration Feedback: One vibration for 4-direction mode, long vibration to restore default 8-direction mode.

Clear All Settings (Reset)

• + A: Clear all settings. Long vibration indicates reset is complete and factory settings are restored.

Continuous Fire (Turbo)

• + ZR: Set Continuous Fire.
• Vibration Feedback: One vibration for Normal Continuous Fire (active when held, stops when released), two for Auto Continuous Fire (press once to start, press again to stop), long vibration to cancel (default).

A-B X-Y Swap

• + A-B X-Y: Swap button inputs.
• Vibration Feedback: One vibration to swap A-B and X-Y button inputs, long vibration to restore default assignments (default).

Adjust Vibration Intensity

• + (Vibration): Adjust Vibration Intensity.
• Vibration Feedback: One vibration for weak, two for standard (default), three for strong, long vibration to turn off vibration.

Adjust Vibration Mode

• + (Mode): Adjust Vibration Mode.
• Vibration Feedback: One vibration for rotary motor mode, two for GuliKit Maglev haptic mode (default), three for HD vibration mode.

APG Recording File Share

This setting allows you to enter APG read/write mode. Connect the USB data cable to your computer, and a USB drive named "GuliKit dat" should appear. Open this drive to find the "Auto.apg" file, which can be copied for backup or sharing. To overwrite the existing APG file, replace it with a new APG file by copying the desired file into the USB drive.

Note: Once the writing process is complete, the controller will automatically power off. Alternatively, hold the Mode button to power off. Please avoid changing the file name for proper functionality.

Support

For further questions and answers, visit the GuliKit website and navigate to the "Support" section to find "Frequently Asked Questions" (FAQ) related to the controller.

Website: www.gulikit.com

Safety Information

CAUTION! This product contains small parts such as buttons, joystick caps, and screws that may cause suffocation if swallowed by children.

Power Off

The controller will automatically power off after 15 minutes of inactivity. Press and hold the Home button for 10 seconds to turn off the controller. Alternatively, press the OFF button on the back.

Note: The controller will not power off when using the full-auto Continuous Fire or replay function (Auto Pilot Gaming).