Sealey TIG Welding Gauntlets - Pair

Introduction

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

Important: Please read these instructions carefully. Note the safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.

Quality goat skin TIG welding leather gauntlets with 160mm split cow leather cuff. 330mm Length. Conforms to BS EN 388 and BS EN 12477:2001. Size range: 9, 10, 11.

Notified Body: ITS Testing Services (UK) Limited, Ventre Court, Meridian Business Park, Leicester, LE19 1WD

Type Examination Certificate Number: LEC FI00339435

Approved Body No: 0362

Safety

• ✔️ For multilayer gloves that can be separated, the performance levels are only applicable to the whole glove including all layers.
• DO NOT use where there is risk of entanglement by moving parts.
• When gloves are intended for arc welding: these gloves do not provide protection against electric shock caused by defective or live working equipment. Note that electrical resistance is reduced if the gloves are wet, dirty or soaked with sweat. This could increase the risk of electric shock.
• Protection is only given to the palm of the hand; the cuff will give adequate protection against small splashes of molten metal.
• There are substances in the glove which are known to cause allergies. A list of raw substances is available upon request.
• Type B gloves are recommended when high dexterity is required, as for TIG welding. Type A gloves are recommended for other welding processes.
• There is no standardized test method at present for detecting UV penetration of materials for gloves, but the current methods of construction of protective gloves for welders do not normally allow penetration of UV radiation.

Performance

Mechanical Risks (EN 388)

Thermal Risks (Heat/Flame) (EN 407)

Protective Gloves for Welders (EN 12477)

Instructions for Use

4.1. Wearing the Gauntlets

Place glove over hand, fitting the thumb and fingers in the appropriate positions. Ensure the glove is fitted comfortably to carry out the task at hand.

4.2. Removing the Gauntlets

Remove by pulling the glove upward from the fingers.

Maintenance

• DO NOT wash or tumble dry.
• The packaging provided with the glove is suitable for the required transport.
• This product does not have an expiry date, but should be replaced when worn/damaged.

Environment Protection

This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed at www.sealey.co.uk.

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

[Register Your Purchase Here]

Notes and Warranty

Note: It is Sealey's policy to continually improve products and as such they reserve the right to alter data, specifications and component parts without prior notice. Other versions of this product may be available. For alternative versions, please email or call the technical team on technical@sealey.co.uk or 01284 757505.

Important: No liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey EU Ltd: Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland

Sealey Group UK: Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Contact: 01284 757500 | sales@sealey.co.uk | www.sealey.co.uk

Document version: SSP142.V4 Issue 1 18/09/23