Sealey Welding Head Shield - Shade 10

1. SAFETY

? Refer to instructions

• Ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The head shield will not offer protection against misuse of workshop tools, equipment, or accessories.
• This head shield is designed for eye and face protection during the following operations: manual metal arc welding, TIG welding, pulsed arc welding and plasma cutting.
• ⚠️ WARNING! This head shield is not suitable for use with laser welding or oxygen acetylene welding or cutting.
• Prior to using the head shield for the first time ensure that any protective film is removed from the internal and external lenses.
• Maintain the head shield in good condition.
• Ensure that the clear lens is kept clean and is securely attached to the head shield.
• Fit the head shield and adjust the head band so the head shield will sit as low and near to your face as possible.
• Use head shield only in temperatures ranging from -10°C to 60°C.
• Remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
• Maintain correct balance and footing.
• Ensure the floor is clear from obstructions, not slippery and wear non-slip shoes.
• Keep children and unauthorised persons away from the working area.
• Replace the lenses if they become scratched or covered in weld spatter.
• ⚠️ WARNING! The head shield will only protect the eyes/face from radiation and weld spatter.
• ⚠️ WARNING! The head shield will not protect against explosive devices or corrosive liquids.
• ❌ DO NOT use the head shield for any purpose for which it is not designed.
• ❌ DO NOT use the head shield unless you have been instructed in its use by a qualified person.
• ❌ DO NOT get the head shield wet or use in damp or wet locations.
• ❌ DO NOT leave work place with head shield in lowered position.
• ❌ DO NOT place the head shield on a hot surface.
• ❌ DO NOT use the head shield without the correct shade (filter) for the desired application.
• ⚠️ WARNING! During the welding process hazardous ultraviolet and infrared rays are emitted which can injure the eyes and cause skin burns.
• It is advisable to wear suitable additional safety clothing to protect the rest of the body during the welding process.
• After use, clean head shield and store in a safe, dry, childproof location in its original packaging.
• ⚠️ WARNING! DO NOT use the helmet if damaged or you suspect it may be faulty. (Contact Sealey stockist).
• ⚠️ WARNING! Welding vapours and gases can be harmful to your health. Keep your head away from any fumes, work in a well ventilated area.

2. INTRODUCTION

This welding head shield features a polypropylene shell and an adjustable headband. It includes a 2" x 4-1/4" front flip lens for quick and easy weld inspection. The shield is supplied with a shade 10 lens and conforms to BS EN 175.

3. SPECIFICATION

4. ASSEMBLY

4.1. ATTACHING THE HEADBAND

1. Unscrew and remove the thumb wheel on one side of the headband (see figure 1).
2. Locate the exposed threaded spindle through the fixing hole in the head shield body (see figure 2).
3. Clip the tilt tab onto the locating stud on the head shield (see figure 3).
4. Reattach the thumbscrew and tighten (see figure 4).
5. Repeat for the other side.

Diagram Descriptions:

• Figure 1: Illustrates the headband with a thumb wheel and threaded spindle.
• Figure 2: Shows the head shield body with a fixing hole and a threaded spindle.
• Figure 3: Depicts the tilt tab on the headband and the locating stud on the head shield.
• Figure 4: Shows the reassembled headband attached to the head shield with the thumbscrew.

5. ADJUSTMENT

5.1. ADJUSTING THE HEADBAND CIRCUMFERENCE

Adjust the headband circumference with the thumb wheel located at the rear of the headband (see figure 5). Turn clockwise to tighten and counterclockwise to loosen.

Figure 5: Shows the rear of the headband with the circumference adjustment thumbwheel.

5.2. ADJUSTING THE HEADBAND HEIGHT

Adjust the height by snapping the pins on the top band of the headband into the desired position (see figure 6).

Figure 6: Shows the top band of the headband with height adjustment pins.

5.3. ADJUSTING THE HEADBAND TILT ANGLE

Adjust the tilt angle by loosening the thumbscrews on both sides of the head shield (refer to figure 2) and change the tilt tab to the desired angle (refer to figure 3). There are four pre-set positions to select. Re-tighten the thumbscrews.

6. MAINTENANCE

6.1. REPLACING THE SHADE LENS

1. Flip up the front shade lens holder (see figure 7).
2. Locate thumb or forefinger under the lens retainer clip (see figure 8) and gently pull inwards and outwards to remove the lens retainer. Place the retainer in a secure position.
3. Remove the shade lens and replace with a new one.
4. Replace the lens retainer by clicking it back into place.

6.1.5. REPLACING THE CLEAR LENS

1. Locate thumb or forefinger under the lens retainer clip (see figure 8) and gently pull inwards and outwards to remove the lens retainer. Place the retainer in a secure position.
2. Remove the clear lens and replace with a new one.
3. Replace the lens retainer by clicking it back into place.

Diagram Descriptions:

• Figure 7: Shows the front shade lens holder being flipped up.
• Figure 8: Illustrates the lens retainer clip.

6.2. CLEANING

1. Clean with a soft cloth.
2. ❌ DO NOT use solvents.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Notes and Warranty

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.