Infinix NOTE 40 X6853 User Manual
Exploded Diagram Specification
The following table details the components of the Infinix NOTE 40 (X6853):
| Part Number | Component | Part Number | Component |
|---|---|---|---|
| 1 | TP+LCM | 2 | FRONT HOUSING GRAPHITE_FILM |
| 3 | GRAPHITE PLATE | 4 | MIDDLE HOUSING |
| 5 | FRONT CAMERA FRAME | 6 | FRONT CAMERA GROUNDING COPPER FOIL |
| 7 | 32M CAMERA | 8 | SHIELDING CASE COPPER FOIL |
| 9 | MAIN BOARD | 10 | 108M CAMERA GROUNDING COPPER FOIL |
| 11 | 108M CAMERA | 12 | 8W CAMERA |
| 13 | 8W CAMERA CONDUCTIVE_FABRIC | 14 | 2M CAMERA |
| 15 | 2M CAMERA RUBBER | 16 | RECEIVER |
| 17 | MAIN FPC | 18 | BATTERY |
| 19 | UP FRAME | 20 | FLASH LAMP FPC |
| 21 | STEEL | 22 | MAIN PCB HEAT FILM |
| 23 | UP FRAME HEAT FILM | 24 | NFC WIRELESS FPC |
| 25 | COAXIAL CABLE 1 | 26 | COAXIAL CABLE 2 |
| 27 | SCREW | 28 | BATTERY COVER |
| 29 | REAR CAMERA DECORATION | 30 | REAR CAMERA LENS |
| 31 | 108M CAMERA LENS | 32 | 2M CAMERA LENS |
| 33 | SIM CONNECTOR | 34 | SPK BOX FRAME |
| 35 | ANTENNA SUB ADHESIVE | 36 | ANTENNA SUB |
| 37 | COAXIAL CABLE MYLAR | 38 | USB RUBBER |
| 39 | SUB RUBBER | 40 | FINGERPRINT |
| 41 | MOTOR | 42 | FINGERPRINT FOAM |
| 43 | LCM RUBBER |
Know Your Phone
The Infinix NOTE 40 has the following external features:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button
- 5. NFC & Wireless charging indicator
SIM/SD Card Installation
- Ensure your phone is powered off.
- Refer to the diagram for correct SIM/SD card placement.
Charging the Phone
You can charge your Infinix NOTE 40 using the provided Infinix charger and USB cable, or by connecting it to a computer via USB. Using non-approved chargers or cables may damage the device and void the warranty.
The charging port is a USB Type-C connector located on the bottom of the device.
FCC Caution
Labelling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and may radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device type: X6853 (FCC ID: 2AIZN-YYS-X6853) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.08 W/kg, and when properly worn on the body is 0.67 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS, and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System: Android™
Android is a trademark of Google LLC.
