Landmann Big Sky Fire Pit Assembly Instructions and Owner's Manual

Product Information

Brand: Landmann

Product Type: Fire Pit

Model Series: Big Sky

Applicable Models: 28673, 28677, 28674, 28678, 28675, 28679

Rules for Safe Operation

[!] FOR OUTDOOR USE ONLY!

[!] USE ONLY ON BRICK, CONCRETE, STONE OR OTHER MASONRY SURFACES!

[!] DO NOT USE ON LAWNS, WOODEN DECKS OR ASPHALT!

[!] KEEP BIG SKY AWAY FROM BUILDINGS, FLAMMABLE ITEMS AND VEHICLES.

[!] THE BIG SKY FIRE PIT IS FOR ADULT USE ONLY.

[!] DO NOT LEAVE UNATTENDED AT ANY TIME WHILE IN USE.

[!] KEEP SPARK GUARD ON BIG SKY WHILE IN USE.

[!] DO NOT USE IN WINDY CONDITIONS!

[!] DO NOT OVERLOAD OR USE FOR BURNING GARBAGE.

[!] NEVER USE GASOLINE, ALCOHOL OR VOLATILE FLUIDS TO START FIRES.

[!] NEVER USE UNDER LOW HANGING TREE BRANCHES, TRELLIS, OVERHANGS OF ANY KIND INCLUDING COVERED PORCHES.

[!] USE CAUTION WHEN TENDING THE FIRE, AS SURFACES WILL BE HOT WHILE IN USE.

[!] BEFORE EACH USE MAKE SURE BIG SKY IS IN GOOD WORKING CONDITION.

[!] USE CAUTION AFTER THE FIRE HAS BEEN EXTINGUISHED, SURFACES WILL REMAIN HOT FOR SOME TIME.

Parts List

• A: Spark Guard Cover (1)
• B: Cooking Grate (1)
• C: Fire Pit (1)
• D: Ring Sections (3)
• E: Legs (3)
• F: Multi-Purpose Poker (1)
• G: Cooking Grate Pins (3)
• H: Nuts (6)
• I: Washers (6)
• J: Bolts (6)

Tools Needed for Assembly

• Adjustable Wrench
• Phillips Screw Driver

Assembly Instructions

1. Step 1: Attach the three legs (E) to the fire pit (C) using six washers (I) and six nuts (H). Tighten securely.
2. Step 2: Attach one ring section (D) to the fire pit (C) using two bolts (J). Loosely tighten the bolts.
3. Step 3: Repeat Step 2 for the remaining two ring sections (D). Ensure all three ring sections fit together to form a continuous ring. Tighten all bolts securely.
4. Step 4: Thread the three cooking grate pins (G) into the nuts welded on the inside of the fire pit (C). Do not overtighten.
5. Step 5: Place the spark guard (A) onto the cooking grate pins (G). The spark guard is used to keep sparks contained within the fire pit. Use at all times.
6. Step 6: Before use, place 5 lbs of sand on the bottom of the fire pit (C). The sand insulates the area below the pit and protects against the corrosive nature of ashes.

Helpful Hints for Usage

• Adding sand to the bottom of the Big Sky helps protect against the corrosive nature of ashes and will extend the life of the pit.
• Burn your Big Sky three times before using to cook on.
• If not using for a long period, store away from weather and elements.
• Do not let your Big Sky fill with water.
• Do not dump ashes where they could start a fire.
• Dispose of ashes in a proper receptacle only after ashes have cooled.

Cooking Grate Usage

If you wish to grill, place the cooking grate (B) on the cooking grate pins (G). Please note: Remove the cooking grate when not grilling.

Sandpaint Finish

Note: Since the heat intensity from the fires will vary depending on the type and amount of fuel used, you may experience minimal peeling or flaking of the paint. This is normal and will not affect the safety or performance of this fire pit.

Contact and Warranty Information

Congratulations on your purchase of the Big Sky Fire Pit!

For missing or defective parts, please contact Landmann USA:

Email: customerservice@landmann-usa.com

Phone: 1-800-321-3473 (Monday-Friday, 8 AM - 5 PM Eastern Time)

Proof of purchase may be required. Thank you!

Landmann USA, Cartersville, GA 30120. Made in China. © 2008 Landmann USA.