Vax Rapid Power Carpet Cleaner

Introduction

Thank you for purchasing the Vax Rapid Power carpet cleaner. This user guide is designed to help you get the most out of your machine and maintain your carpets for longer, fresher results.

The Vax Rapid Power is designed to make washing carpets regularly, as effective and efficient as possible. Maintaining your carpets will ensure they keep their appearance for longer and smell fresh and clean. You've chosen carpets for your home for a reason and Vax will help you take good care of them.

This guide also contains instructions on maintaining your new machine, so that it's always ready when you are to tackle your carpets.

Included with Your Machine

Standard Tools

• Wash tool
• Accessory bag
• 2x 250ml Ultra+ solution

Rapid Power Advance (Standard tools included, plus:)

• 2.5m Hose

Rapid Power Deluxe (Standard tools included, plus:)

• 4.6m Hose
• SpinScrub tool
• Hard floor tool
• Pre-treatment wand
• 250ml Pre-treatment solution

Getting to Know Your Machine

The Vax Rapid Power carpet cleaner features several key components:

• Handle: For gripping and maneuvering the machine.
• Trigger (hidden): Located on the handle, releases water/solution mix.
• Clean water/solution tank release button: Used to detach the tank.
• Clean water tank cap: For filling the clean water tank.
• Wash/Rinse dial: Selects the cleaning mode (Wash or Rinse).
• Dirty water tank release latch: For removing the dirty water tank.
• Dirty water tank: Collects dirty water.
• Accessory hose connector cover: Covers the port for hose attachments.
• Nozzle release clip: For detaching the nozzle.
• Cleaning Mode Dial: Selects cleaning modes like Quick Clean or Deep Clean.
• SpinScrub brushes and brushbar: Rotating brushes for deep cleaning.
• Solution tank cap: For filling the solution.
• Quick cord release hook: For winding the power cord.
• Handle lock dial: Secures the handle position.
• Hose connector port (hidden): For attaching the hose.
• Nozzle: The cleaning head that applies solution and picks up dirt.
• Recline pedal: Allows the machine to be reclined for use.
• Hard floor tool (selected models): Attachment for cleaning hard floors.
• On/Off pedal: Powers the machine on and off.

Technical Specification

Subject to technical change without notice.

To purchase consumables and accessories, please visit vax.co.uk

Getting Started

PLEASE READ 'LET'S TALK SAFETY' AT THE BEGINNING BEFORE USE.

IMPORTANT: Flooring should be dry vacuumed thoroughly before washing.

Test for Colourfastness

Wet a white absorbent cloth with the solution. In a small hidden area of your carpet/rugs/upholstery, gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with a white paper towel or cloth. If your carpet has more than one colour, check all colours.

Test Your Carpet/Rugs/Upholstery

Run the carpet washer over a small hidden area. If no pile distortion occurs, continue cleaning. When cleaning an entire room, move furniture out of the area to be cleaned. If furniture cannot be moved, place aluminium foil or wax paper under the legs to prevent wood finishes from staining your carpet. Pin up furniture skirts and curtains.

When using the carpet washer, basic safety precautions should always be observed, and do not over-saturate your carpets. Only use Vax carpet solution; using other solutions may cause excess foaming and invalidate your guarantee. The clean water tank should only be filled with warm water (max 40°C). Filling the clean water tank with hot or boiling water will damage your machine and invalidate the guarantee.

This is a powerful carpet washer. Before plugging in, make sure all controls are turned off. Hold the carpet washer firmly when starting and during use.

Assembling Your Carpet Washer

1. Stand the base of the carpet washer on the floor in the upright position. Line up the handle with the main body and push into place.
2. Turn the handle lock dial clockwise to lock into position.
3. Assemble the tanks by tilting and lining up the front of the tank with the washer and pushing the tank back until it clicks into place.

Using Your Machine

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

IMPORTANT: Your dirty water tank is fitted with a float. When the dirty water tank is full, or the floorhead is not in contact with the carpet, the float will shut off the suction. You will hear the motor noise increase. Once the float is activated, empty the dirty water tank. If the tank is not full, turn off the machine and wait for the float to settle.

NOTE: Carpets should be dry vacuumed thoroughly before washing. For heavily soiled areas, it may be necessary to repeat the cleaning process. Make criss-crossing strokes across the original pattern and overlap with each pass.

Filling the Water/Solution Tank and Cleaning Modes

Quick Clean Mode: Best for a quick, surface clean; carpets dry in less than 1 hour.

Deep Clean Mode: Best overall results for a thorough, deep clean.

1. Press the clean water/solution tank release button and pull to remove the tank.
2. Twist the solution tank cap anti-clockwise and remove.
3. Pour the required amount of carpet cleaning solution into the tank. Tighten the cap before returning the tank to the unit.
4. Fill the clean water tank with warm water (max 40°C). Fill to the max fill line for a Deep Clean, and to the Quick Clean fill line for a quick surface clean.
5. Tilt and line up the front of the tank with the washer, and push the tank back until it clicks into place.
6. Turn the Wash/Rinse dial to 'wash'. The SpinScrub brushes and brushbar will deep clean your carpets with water and solution, removing dirt and stains.
7. Plug into mains and press the On/Off button to switch on.

This machine has an auto-mix tank, so any unused solution can be poured back into the bottle. ?

Choosing Cleaning Mode

Choose the cleaning mode by turning the dial on the base:

• Quick Clean Mode: Best for a quick, surface clean with carpets drying in less than 1 hour.
• Deep Clean Mode: Best overall results for a thorough, deep clean.

Operating the Carpet Washer

1. Press the recline pedal and pull the handle backwards.
2. Squeeze the trigger to release solution and water mix.
3. For best results, apply water/solution on the forward stroke and release the trigger to pick up water/solution on the backward stroke. For a dryer finish, follow with an additional dry stroke with no trigger pressed.
4. Turn the Wash/Rinse dial to 'rinse'. Only water is released to remove solution residue.

For best cleaning results, use slow, straight parallel strokes. Intermittent dry forward strokes will increase water pick up. The 'rinse' mode will also work when using the hose. ?

Using the Hose and Tools (Selected Models Only)

CAUTION: Test for colourfastness – Wet a white absorbent cloth with the solution. In a small hidden area of your carpet/rugs/upholstery, gently rub with the dampened cloth. Wait ten minutes and check for colour removal or bleed with a white paper towel or cloth. If your carpet has more than one colour, check all colours.

NOTE: The carpet washer should be in the upright position when using the hose and tools, de-activating the SpinScrub brushes and brushbar.

1. Pour the required amount of carpet cleaning solution into the solution tank.
2. Fill the clean water tank with warm water (max 40°C).
3. Turn the Wash/Rinse dial to 'wash'.
4. Pull down the accessory hose connector cover.
5. Push the hose end and hose solution connector into the connection port until it clicks into place.
6. Slide the selected tool over the tab at the end of the hose until it clicks into place.
7. Plug into mains and press the On/Off button to switch on.
8. Press the trigger on the hose to release solution/water.
9. Squeeze the trigger on the forward stroke, release the trigger on the backward stroke to recover solution/water. For a dryer finish, follow with an additional dry stroke with no trigger pressed.

Use the carpet washer or hose to pick up spills before washing and cleaning the area. ?

Pre-treatment Wand (Selected Models Only)

1. Pour the required amount of pre-treatment solution into the solution tank.
2. Fill the clean water tank with warm water (max 40°C).
3. Turn the Wash/Rinse dial to 'wash'.
4. Pull down the accessory hose connector cover.
5. Push the wand connector into the solution tube port.
6. Plug into mains, press the On/Off button to switch on.
7. Press and hold the trigger on the pre-treatment wand, spraying evenly over stubborn stains.
8. Leave the solution for 10-15 minutes before washing the carpet.

Washing Hard Floors (Selected Models Only)

CAUTION: To prevent damage to wood floors and other hard floors, follow the flooring manufacturer's cleaning recommendations. Inspect floor surface for worn finish, bare wood or separated joints. If it's not recommended to use the carpet washer on floors if any of these conditions exist.

IMPORTANT: Before attaching the hard floor squeegee onto the carpet washer, remove tanks or make sure tanks are empty before lying the carpet washer on its back.

1. Lie the carpet washer on its back, line up the squeegee with the nozzle.
2. Hook the front of the squeegee onto the edge of the nozzle.
3. Push the squeegee under the nozzle until it clicks into place.

Emptying the Dirty Water Tank

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

1. Press the dirty water tank release latch, pull to remove the dirty water tank.
2. Pull and lift the dirty water tank clip to release the lid. Lift to remove the dirty water tank lid.
3. Empty dirty water over the sink. Rinse the dirty water tank and lid under water to remove dirt/debris.
4. Clean the filter screen located at the back of the dirty water tank.
5. To re-fit, tilt the dirty water tank and line it up onto the carpet washer. Push back until it clicks into place.

❗ IMPORTANT: Empty and rinse out clean and dirty water tanks and leave to air dry before replacing. Do not leave solution stored in the tanks between uses.

Taking Care of Your Machine

Removing and Cleaning the Nozzle

1. Remove both tanks and tilt the carpet washer back.
2. Lift the nozzle release clip and pull forward, separating tabs on the nozzle and carpet washer.
3. Rinse the nozzle under water to remove dirt/debris.
4. Replace the nozzle by lining up tabs on the nozzle with tabs underneath the front of the carpet washer. Push the nozzle down until it clicks into place.

Removing Blockages from the Brushbar and SpinScrub Brushes

1. Using a pair of scissors, remove any threads or hair caught around the brushbar.
2. Using a crosshead screwdriver, remove the bottom screws from each of the rug guards (metal pins) so the bottom of the pin is released. Unclip the top of each pin to release.
3. Firmly pull the sides of the SpinScrub cover to remove it.
4. Line up the spindle and tabs on the side of the spin scrub cover into the carpet washer, push firmly until it clicks into place.

Let's Talk Technical

CAUTION: Always unplug the carpet washer before performing any maintenance/troubleshooting checks.

Changing the Brushbar

1. Lie the carpet washer on its back, exposing SpinScrub brushes and brushbar.
2. Using a crosshead screwdriver, remove the bottom screws from each of the rug guards (metal pins), so the bottom of the pin is released. Unclip the top of each to release.
3. Firmly pull the sides of the SpinScrub cover and remove SpinScrub brushes.
4. Use a crosshead screwdriver, undo 2 screws and remove the belt guard.
5. Undo the four screws on the side brushes.
6. Pull and slide the left side brushes and remove the side cap from the brushbar.
7. Pull and slide the right side brushes together with the brushbar. Remove the side cap from the brushbar and unloop the brushbar from the belt.
8. Loop the replacement brushbar through the belt and onto the belt grip.

Changing the Brushbar (Continued)

1. Line up the 'right' side brushes with the base and slide into place. Attach the brushbar to the side brushes.
2. Attach the other side of the brushbar to the side brushes. Slide onto the side of the base and into place.
3. Refit the belt guard and tighten x2 screws. Refit and tighten screws x2 on either side of the side brushes. There are 6 screws in total.
4. Refit SpinScrub brushes and rug guard. Refit rug guard pins and tighten screws.

What to Do If It Goes Wrong

CAUTION: To reduce the risk of personal injury, unplug the carpet washer before performing maintenance/troubleshooting checks.

Troubleshooting Guide

• Problem: Is there an accessory missing?
  • Solution: Check the contents panel on the box to make sure the part is definitely included in your unit.
• Problem: Why won't the carpet washer turn on?
  • Solution: The plug may not be fully pushed into the electrical socket. Check the fuse in the plug; if it needs replacing, always replace with a British 13amp fuse.
• Problem: Why won't the solution/clean water dispense?
  • Solution: Make sure the clean water tank is fitted securely. Go to ‘Using your machine’. The Wash/Rinse dial has been set to 'Rinse'; set dial to 'Wash' to dispense solution. The clean water tank valve may be stuck; hold the clean water tank over the sink and press the valve underneath to release. Squeeze the trigger on the handle to release solution and water mix. Water/solution tank is empty; go to ‘Using your machine’ for how to refill.
• Problem: Why won't the carpet washer pick up?
  • Solution: The float in the dirty water tank may have been activated. Empty the dirty water tank and wait for the float to settle before re-starting your carpet washer. The accessory hose connector cover has not been correctly closed; correctly close cover. Check the SpinScrub brushes and brushbar for blockages and clear. The dirty water tank may not be fitted correctly; re-fit making sure the lid is pushed down securely. Go to ‘Taking care of your machine’. Check the nozzle for blockages and clear. Go to 'Taking care of your machine'. Check the nozzle is correctly fitted. Go to ‘Taking care of your machine’. Check the filter screen located in the dirty water tank for dirt and debris. Go to 'Emptying the dirty water tank'.
• Problem: Why won't the brushes spin?
  • Solution: The brushes will only spin when the carpet washer is reclined. Check the SpinScrub brushes and brushbar for blockages and clear. Check for damage to the brushbar and the spindle on the back of the SpinScrub brush.

Getting in Touch

It's quick and easy to register for your FREE 6 year guarantee*.

Online at: vax.co.uk/registration

Please retain your original receipt for proof of purchase.

We're here if you need us:

vax.co.uk/support

*Registration required. Terms and conditions apply.

Accessories

Don't forget your accessories!

Order at: www.vax.co.uk/spares-and-solutions

Ultra+ Carpet Cleaning Solution (1.5l)

Product Code: 1-9-132706-00

Tackles stubborn spots and stains and removes unpleasant odours too. It's specially formulated to leave no sticky residue, so your carpets stay fresher for longer.

Ultra+ Pet Carpet Cleaning Solution (1.5l)

Product Code: 1-9-132707-00

Tackles stubborn spots and stains and removes unpleasant pet odours too. It's specially formulated to leave no sticky residue, so your carpets stay fresher for longer.

Ultra+ Refresh & Revitalise (1.5l)

Product Code: 1-9-133260-00

Tackles stubborn spots and stains. Its Oxy-Lift Action Technology brings your carpets back to life and restores carpet pile. Formulated to leave no sticky residue, so your carpets stay fresher for longer. Safe to use on wool carpets - Woolsafe approved.

Ultra+ Allergen (1.5l)

Product Code: 1-9-133262-00

Tackles stubborn spots and stains, but also removes deep down dirt and allergens in your carpet. Formulated to leave no sticky residue, so your carpets stay fresher for longer. Ultra+ Allergen carpet cleaning solution is approved by the British Allergy Foundation.

Ultra+ Sanitise (1.5l)

Product Code: 1-9-133261-00

Tackles stubborn spots and stains and removes embedded dust and dirt from carpet pile. Ultra+ Sanitise is formulated to leave no sticky residue, so your carpets stay fresher for longer.

Notes

[Blank section]

Get In Touch

Email: info@vax.co.uk

Website: vax.co.uk

EU Statement of Compliance

Manufacturer/EU importer: Vax Limited, hereby on our own responsibility, declare that the ECJ1PAV1 and ECW1PAV1 are manufactured in compliance with the following Directives: Safety: 2014/35/EU Low Voltage Directive. EMC: 2014/30/EU Electromagnetic Compatibility Directive.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

© 2017 Vax Limited. All rights reserved. The VAX trade mark and Vax lozenge is the property of Techtronic Floor Care Technology Ltd and is registered in the EU and may be pending or registered in other countries.