ATK Blazing Sky X1 Ultimate Lightweight Wireless Mouse

Product Information

Material: 120G writing paper

Folded Size: 96*96mm

Folding Method: Accordion fold

The folded side is the cover.

[Diagram: Illustration of an accordion-folded booklet with the ATK logo and 'USER GUIDE' text.]

Model Series: Blazing Sky X1 SERIES

01 Introduction / Key and Accessory Description

Manufacturer: Shenzhen Yizhita Technology Co., Ltd

Manufacturer Address: 4th Floor, Unit 4219, Building 1, Huiheng Building, No. 138, Gaoxin South 7th Road, High-tech Park Community, Yuehai Street, Nanshan District, Shenzhen

Key Components:

• 1. Type-C Port: Type-C interface for charging and wired connection.
• 2. Left Mouse Button: Primary click button.
• 3. Right Mouse Button: Secondary click button.
• 4. Scroll Wheel: For scrolling and middle-click functionality.
• 5. LED Indicator: Provides status information.
• 6. Forward Side Button: Navigates forward in applications.
• 7. Back Side Button: Navigates back in applications.
• 8. Feet Area: Low-friction pads for smooth gliding.
• 9. Optical Sensor: Tracks mouse movement.
• 10. DPI Button: Cycles through DPI settings.
• 11. Power Switch: Turns the mouse on or off.
• 12. Cable: For charging and wired use.
• 13. 8K Receiver: Dongle for high-polling-rate wireless connection.

[Diagram: Top, side, and bottom views of the mouse with numbered callouts corresponding to the key components.]

02 Quick Start

1. Charge / Wired Mode: Connect the mouse using the provided Type-C cable.
   Rating: 5V 200mA
2. Wireless Mode:
   1. Plug the 8K Receiver (13) into a USB port on your computer.
   2. Ensure the mouse's Power Switch (11) is set to 'ON'.
   3. [Diagram: Illustration showing plugging the 8K receiver into a computer.]
   4. Recommended connection distance: Less than 2m.
   5. Maximum connection distance: Greater than 10m.

03 DPI Setting

Press and hold the two side keys (6 & 7) for over three seconds to quickly switch DPI. The mouse offers the following DPI levels with corresponding LED indicator colors (without requiring driver software):

• 400 DPI: Red light
• 800 DPI: Green light
• 1600 DPI: Blue light
• 3200 DPI: Purple light

For Blazing Sky X1 PRO / X1 PRO MAX / X1 ULTRA: Further DPI adjustments are available via the driver software, supporting settings between 200-26000 DPI.

For Blazing Sky X1 ULTIMATE: Further DPI adjustments are available via the driver software, supporting settings between 50-36000 DPI.

04 Polling Rate Setting

The polling rate can be directly adjusted using the driver software.

05 Battery Indication

1. Blinking Red: Battery level below 20%, please charge.
2. Blinking Yellow: Charging in progress.
3. Solid Green: Charging complete.

FCC Compliance Information

FCC ID: 2BE9P-ATKX1ULTIMATE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF Radiation Exposure Statement: This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body.

8K Receiver Instructions

Website for Downloads: WWW.ATK.PRO (Drivers/Firmware)

1. Step 1: Connect the 8K receiver to your computer using the original ATK data cable or another Type-C cable.
2. Step 2: Log in to the official website (WWW.ATK.PRO) and download the latest driver/firmware.
3. Step 3: Upgrade the firmware of your compatible mouse to the latest version.
4. Step 4: On the ATK official website's driver/firmware download page, navigate to the settings section to pair the dongle.
5. Step 5: Follow the on-screen instructions to pair the 8K receiver with your compatible mouse.
6. Step 6: Once successfully paired, the indicator light on the 8K receiver will illuminate. You can then adjust the polling rate in the driver's performance settings for the corresponding mouse.

[Diagram: Steps for pairing the 8K receiver with the mouse.]

Indicator Light Status:

• The 8K receiver has an indicator light to show mouse connection status and battery level.
• Connection Status (Connected Successfully): Indicator light is solid.
• Lighting Effects: Constant, Breathing, Flowing, Neon, Rainbow Constant, Mixed Breathing.
• Battery Indicator: Normally displays regular lighting effects. The light turns solid red when the battery is below 10%.

Software Download

Download the latest software from: WWW.ATK.PRO

FAQ / Troubleshooting

Battery Recycling Information

[Diagram: Illustration indicating Li-ion battery and removal instructions for recycling.]