ATK 406 Rotax Engine Spare Parts List
Edition 88-96
ATK Motorcycles
1163 W 850 N
CENTERVILLE UT. 84014
(801) 298-8288
Table of Contents
Page 1: Crankcase
Page 4: Crankshaft, Piston, Cylinder, Cylinder Head, Reed Valve
Page 9: 5-speed transmission
Page 13: Clutch, Kick Start
Page 16: Magneto Cover, Clutch Cover
Page 18: Motoplat Magneto-Generator 6V 40/21/10W
Page 20: Repair Tools, Gasket Set
Crankcase
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1-4 | 292 049 | GEHAEUSE KPL. / CRANKCASE ASSY. | 1 |
| 260 470 | GEHAEUSERING / CRANKCASE RING | 2 | |
| 3 | 229 140 | PASSHUELSE 9,8X10 / DOWEL 9,3X10 | 1 |
| 4 | 229 160 | PASSHUELSE 13,8X15 / DOWEL 13,8X15 | 1 |
| 5 | 230 425 | WD-RING AS 28X38X7 / OIL SEAL 28X38X7 FOR MAGNETO AND CLUTCH SIDE |
2 |
| 6 | 230 395 | WD-RING AS 25X40X7 / OIL SEAL 25X40X7 FOR MAIN SHAFT |
1 |
| 7 | 932 420 | RK-LAGER 6205 C3 BALL BEARING 6205 C3, 25-52-15 FOR MAIN SHAFT |
1 |
| 8 | 232 850 | RK-LAGER 6203 E TVH C3 BALL BEARING 6203E TVH, 17-40-12 FOR CLUTCH SHAFT |
1 |
| 9 | 239 750 | INDEXFEDER / INDEX SPRING | 1 |
| 10 | 248 977 | ROLLENINDEX KPL. / INDEX LEVER ASSY. | 1 |
| 11 | 227 800 | ANLAUFSCHEIBE 16,2/21/0,4 THRUST WASHER 16,2/21/0,4 |
1 |
| 12 | 945 840 | SICHERUNGSRING 15X1 DIN 471 LOCKING RING 15X1 |
1 |
| 13 | 945 751 | FEDERRING A6 DIN 128 / LOCK WASHER A6 | 13 |
| 14 | 241 871 | ZYL SCHRAUBE M6X70 DIN 912 ALLEN SCREW M6X70 |
8 |
| 15 | 240 330 | ZYL.SCHRAUBE M6X55 DIN 912 ALLEN SCREW M6X55 |
4 |
| 16 | 241 761 | ZYL SCHRAUBE M6X50 DIN 912 ALLEN SCREW M6X50 |
1 |
| 17 | 932 030 | RK-LAGER 6203 C3 BALL BEARING 6203 C3, 17-40-12 FOR MAIN SHAFT |
1 |
| 18 | 932 432 | RK-LAGER 6204 C3 BALL BEARING 6204 C3, 20-47-14 FOR CLUTCH SHAFT |
1 |
| 19 | 227 610 | AUSGLEICHSCHEIBE 40/46,5/0,5 SHIM 40/46,5/0,5 FOR CLUTCH SHAFT |
AS REQ |
| 19 | 227 611 | AUSGLEICHSCHEIBE 40/46,5/0,3 SHIM 40/46,5/0,3 |
AS REQ |
| 19 | 227 612 | AUSGLEICHSCHEIBE 40/46,5/0,1 SHIM 40/46,5/0,1 |
AS REQ |
| 20 | 227 520 | AUSGLEICHSCHEIBE 34/39,5/0,5 SHIM 34/39,5/0,5 FOR MAIN SHAFT |
AS REQ |
| 20 | 227 521 | AUSGLEICHSCHEIBE 34/39,5/0,3 SHIM 34/39,5/0,3 |
AS REQ |
| 20 | 227 522 | AUSGLEICHSCHEIBE 34/39,5/0,1 SHIM 34/39,5/0,1 |
AS REQ |
| 21 | 227 110 | HALTEBLECH / RETAINING PLATE | 1 |
| 22 | 940 315 | SENKSCHRAUBE M5X12 DIN 963 COUNTERSUNK SCREW M5X12 |
5 |
| 23 | 241 777 | AUSRUECKSCHRAUBE M12 / HEX.SCREW M12 TIGHTENING TORQUE 75 NM |
1 |
| 24 | 241 781 | MAGNETSCHRAUBE M12x1,5 MAGNETIC CRAIN PLUG M12X1,5 |
1 |
| 25 | 950 141 | DICHTRING A8X13 DIN 7603 GASKET RING A8X13 |
1 |
| 26 | 940 251 | SK-SCHRAUBE M8X9 DIN 933 HEX. SCREW M8X9 |
1 |
| 27 | 241 925 | ENTLUEFTERSCHRAUBE M18X1,5 AIR VENT SCREW M18×1,5 |
1 |
| 28 | 240 345 | STIFTSCHRAUBE M10X186 / STUD M10X186 TORQUE 10 NM |
4 |
| 29 | 229 140 | PASSHUELSE 9,8X10 / DOWEL 9,8×10 | 2 |
| 30 | 949 900 | PASSHUELSE 8,4X10 / DOWEL 8,4X10 | 3 |
| 31 | LOCTITE 574 ORANGE 50 CC. SEALING COMPOUND |
NA | |
| 32 | LOCTITE 221 VIOLET 10 CC LOW STRENGTH BOND |
NA |
Crankshaft, Piston, Cylinder, Cylinder Head, Reed Valve
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1 | 292 290 | KURBELWELLE KPL. / CRANKSHAFT ASSY. | 1 |
| 2 | 827 410 | RADIUSSCHEIBE 30,8/39,5/1 DISTANCE RING 30,8/39,5/1 FOR CRANKSHAFT, MAGNETO SIDE |
1 |
| 3 | 944 582 | AUSGLEICHSCHEIBE 30,4/40,5/0,3 SHIM 30,4/40,5/0,3 FOR CRANKSHAFT, MAGNETO SIDE |
AS REQ |
| 3 | 944 583 | AUSGLEICHSCHEIBE 30,4/40,5/0,1 SHIM 30,4/40,5/0,1 |
AS REQ |
| 3 | 944 586 | AUSGLEICHSCHEIBE 30,4/40,5/0,2 SHIM 30,4/40,5/0,2 |
AS REQ |
| 4 | 932 570 | RK-LAGER 6306 C3 BALL BEARING 6306 C3, 30-72-19 FOR CRANKSHAFT, 30-72-19 |
2 |
| 5 | 246 011 | SCHEIBENFEDER 3X5 DIN 6888 WOODRUFF KEY 3X5 |
1 |
| 6 | 245 400 | FEDERRING 18 DIN 7980 / LOCK WASHER 18 | 1 |
| 7 | 942 225 | SK-MUTTER M18X1,5 / HEX. NUT M18X1,5 TIGHTENING TORQUE 100 NM |
1 |
| 8 | 292 139 | PRIMAERTRIEB KPL. / PRIMARY DRIVE ASSY. REPLACE ONLY DRIVE GEAR WITH CLUTCH DRUM ASSY. |
1 |
| 9 | 945 757 | SPERRKANTRING 18 DIN 128 A LOCK WASHER 18 |
1 |
| 10 | 942 220 | SK-MUTTER M18X1.5 DIN 936 HEX. NUT M18X1,5 TIGHTENING TORQUE 80 NM |
1 |
| 11 | 932 904 | KOLBENBOLZENKAEFIG K 18X22X22 NEEDLE CAGE 18X22X22 |
1 |
Piston Assy.
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 12 - 14 | 292 075 | KOLBEN KPL. 84 MM PISTON ASSY. WITH RINGS 84,0 MM STANDARD RED 83,93 MM STANDARD GREEN 83,94 MM |
1 |
| 12 - 14 | 292 076 | KOLBEN KPL. 84,25 MM PISTON ASSY. WITH RINGS 84,25 MM 1ST OVERSIZE RED 84,18 MM 1ST OVERSIZE GREEN, 84,19 MM |
1 |
| 12 | 292 077 | KOLBEN KPL. 84,5 MM PISTON ASSY. WITH RINGS 84,5 MM 2ND OVERSIZE RED 84,43 MM 2ND OVERSIZE GREEN 84,44 MM |
1 |
| 13 | 215 250 | R-RING IS2-84/77,4×2 RECTANGULAR RING 84,0 MM STANDARD |
1 |
| 13 | 215 251 | R-RING I52-84,25/77,65×2 RECTANGULAR RING 84,25 MM 1ST OVERSIZE |
1 |
| 13 | 215 252 | R-RING IS2-84,5/77,9×2 RECTANGULAR RING 84,5 MM 2ND OVERSIZE |
1 |
| 14 | 215 240 | ETL-RING 152-84/77,4×2 SEMI-TRAPEZ RING 84,0 MM STANDARD |
1 |
| 14 | 215 241 | ETL-RING IS2-84,25/77,65×2 SEMI-TRAPEZ RING 84,25 MM 1ST OVERSIZE |
1 |
| 14 | 215 242 | ETL-RING IS2-84,5/77,9×2 SEMI-TRAPEZ RING 84,5 MM 2ND OVERSIZE |
1 |
| 15 | 916 186 | KOLBENBOLZEN 18X11X58,7 PISTON PIN 18×11×587 |
1 |
| 16 | 945 735 | NULLHAKENRING 18 / CIRCLIP 18 | 2 |
Cylinder with Sleeve
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 17 | 230 720 | DICHTUNG / GASKET | 1 |
| 18 | 213 137 | ZYLINDER MIT BUECHSE CYLINDER WITH SLEEVE RED 84,00-84,01 MM / GREEN 84,01-84,02 MM |
1 |
| 19 | 224 188 | VENTILTRAEGER KPL. / REED VALVE ASSY. | 1 |
| 20 | 224 183 | VENTILTRAEGER VULK. / REED VALVE PLATE | 1 |
| 21 | 224 160 | BLATTVENTIL / REED PETAL | 1 |
| 22 | 224 175 | VENTILANSCHLAG / REED PETAL STOP | 1 |
| 23 | 245 090 | FEDERRING A3 DIN 128 / LOCK WASHER A3 | 4 |
| 24 | 240 350 | LINSENSCHRAUBE M3X6 DIN 7985 / SCREW M3X6 | 4 |
| 25 | 945 751 | FEDERRING A6 DIN 128 / LOCK WASHER A6 | 2 |
| 26 | 940 085 | ZYL SCHRAUBE M6X16 DIN 84 SLOTTED HEAD SCREW M6X16 |
2 |
| 27 | 240 165 | STIFTSCHRAUBE M10X81 / STUD M10X81 | 2 |
| 28 | 230 730 | VERDICHTUNGSBEILAGE / COMPRESSION SHIM | 3 |
| 28 | 230 730 | VERDICHTUNGSBEILAGE COMPRESSION SHIM |
AS REQ |
| 29 | 213 290 | ZYLINDERKOPF / CYLINDER HEAD | 1 |
| 30 | 927 410 | SCHEIBE 10,5 DIN 125 / WASHER 10,3 | 6 |
| 31 | 842 142 | SK-MUTTER M10 HOEНЕ 15 / HEX. NUT M10 | 6 |
| 32 | 945 752 | FEDERRING A8 DIN 128 / LOCK-WASHER A8 | 2 |
| 33 | 840 681 | ZYL SCHRAUBE M8X40 DIN 912 ALLEN SCREW M8×40 |
2 |
| 34 - 35 | 267 785 | VERGASERSTUTZEN KPL. RUBBER FLANGE ASSY. TIGHTENING TORQUE 15 NM |
1 |
| 35 | 251 850 | SCHLAUCHSCHELLE 51 / HOSE CLAMP 51 | 1 |
| 36 | 250 311 | SCHEIBE 8,4 DIN 125 WASHER 8,4 | 2 |
| 37 | 940 591 | SK-SCHRAUBE M8X20 DIN 933 HEX.SCREW M8X20 |
2 |
| 38 | 830 271 | DICHTUNG / GASKET | 1 |
Exhaust Socket and Spring Bracket
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 39 | 273 694 | AUSPUFFSTUTZEN / EXHAUST SOCKET | 1 |
| 40 | 224 067 | FEDEREINHAENGUNG / SPRING BRACKET | 2 |
| 41 | 240 081 | ZYL.SCHRAUBE M8X25 DIN 912 ALLEN SCREW M8X25 |
2 |
| 42 | 830 453 | GUMMISCHLAUCH 9,5x14x70 SILENCING TUBE 9,5X14X70 |
4 |
| 43 | 830 454 | GUMMISCHLAUCH 9,5×14×150 SILENCING TUBE 9.5×14×150 |
12 |
| 44 | 830 452 | GUMMISCHLAUCH 9,5×14×35 SILENCING TUBE 9,5X14X35 |
16 |
| 45 | 213 140 | ZYLINDERBUECHSE / CYLINDER SLEEVE | 1 |
| 46 | 292 294 | KURBELWELLENSATZ KPL. CRANKSHAFT REPAIR KIT |
1 |
| 47 | LOCTITE 648 GRUEN LOCTITE 648 GREEN 6 CC HIGH STRENGTH BOND |
NA | |
| 48 | LOCTITE 221 VIOLET 10 CC LOW STRENGTH BOND |
NA |
5-SPEED TRANSMISSION
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1-24 | 281 064 | GETRIEBESATZ 349/406 TRANSMISSION SET 5 SPEED 5-SPEED |
1 |
| 1 | 237 560 | VORGELEGEWELLE 13 Z / CLUTCH SHAFT 13 T. 1ST SPEED |
1 |
| 2 | 232 795 | NADELKAEFIG K 20X24X12 NEEDLE BEARING 20X24X12 |
1 |
| 3 | 235 620 | LOSRAD 17 Z / GEAR 17 T. 4TH SPEED, CLUTCH SHAFT |
1 |
| 4 | 227 475 | ANLAUFSCHEIBE 24,2/27,5/2,3 THRUST WASHER 24,2/27,5/2,3 |
1 |
| 5 | 245 340 | SPRENGRING 24 SNAPRING 24 | 4 |
| 6 | 235 603 | SCHALTRAD 15 Z / GEAR 15 T 3RD SPEED, CLUTCH SHAFT |
1 |
| 7 | 227 445 | ANLAUFSCHEIBE 21,2/27.5/1 THRUST WASHER 21,2/27,5/1 |
1 |
| 8 | 232 805 | NADELKAEFIG K 21X25X13 NEEDLE BEARING 21×25×13 |
1 |
| 9 | 235 665 | LOSRAD 23 Z / GEAR 23 T. 5TH SPEED, CLUTCH SHAFT |
1 |
| 10 | 235 646 | FESTRAD 13 Z / GEAR 13 2ND SPEED, CLUTCH SHAFT |
1 |
| 11 | 237 536 | HAUPTWELLE / MAIN SHAFT | 1 |
| 12 | 232 800 | NADELKAEFIG K 21X25X13 F NEEDLE BEARING 21×25×13 |
1 |
| 13 | 232 740 | NADELKAEFIG K 21×25×10 NEEDLE BEARING 21×25×10 |
1 |
| 14 | 235 658 | LOSRAD 23 Z / GEAR 23 T. 2ND SPEED, MAIN SHAFT |
1 |
| 15 | 227 465 | ANLAUFSCHEIBE 22/30/2,6 THRUST WASHER 22/30/26 |
3 |
| 16 | 235 113 | SCHALTRAD 21 Z GEAR 21 T. 5TH SPEED, MAIN SHAFT |
1 |
| 17 | 235 610 | LOSRAD 21 Z GEAR 21 T. 3RD SPEED, MAIN SHAFT |
1 |
| 18 | 235 633 | SCHALTRAD 19 Z / GEAR 19 4TH SPEED, MAIN SHAFT |
1 |
| 19 | 944 468 | ANLAUFSCHEIBE 20,5/30/1 THRUST WASHER 20,5/30/1 |
1 |
| 20 | 232 790 | NADELKAEFIG K 20X24X12 JP NEEDLE BEARING 20X24X12 |
1 |
| 21 | 235 473 | LOSRAD 31 Z GEAR 31 T. 1ST SPEED, MAIN SHAFT |
1 |
| 22 | 227 430 | ANLAUFSCHEIBE 17,2/30/1 THRUST WASHER 17,2/30/1 |
1 |
| 23 | 245 390 | SICHERUNGSBLECH NA 24 TAB WASHER NA24 | 1 |
| 24 | 242 650 | SK-MUTTER M20X1,5 НОЕНЕ 12 HEX. NUT M20X1,5 TIGHTENING TORQUE 100 NM |
1 |
| 25 | 236 041 | KETTENRAD 15 Z / SPROCKET 15 MOUNTED AS STANDARD |
1 |
| 25 | 236 040 | KETTENRAD 14 Z / SPROCKET 14 T | 1 |
| 25 | 236 042 | KETTENRAD 16 Z / SPROCKET 16 T | 1 |
| 26 | 239 640 | HAARNADELFEDER / SPRING | 1 |
| 27 | 427 070 | SCHEIBE 18,2/34/1 THRUST WASHER 18,2/34/1 |
1 |
| 28 | 258 575 | SCHWENKHEBEL TRANSMISSION ACTUATING LEVER |
1 |
| 29 | 237 511 | SCHALTWELLE / SHIFT SHAFT | 1 |
| 30 | 945 790 | SICHERUNGSSCHEIBE 12 DIN 6799 CIRCLIP 12 |
2 |
Clutch, Kick Start
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1 | 227 600 | ANLAUFSCHEIBE 20,2/35/3 THRUST WASHER 20,2/35/3 |
1 |
| 2 | 232 700 | INNENRING / INNER RACE | 2 |
| 3 | 232 650 | NADELKAEFIG K 25X29X10 NEEDLE BEARING 25×29×10 |
2 |
| 4 | 292 139 | PRIMAERTRIEB KPL. / PRIMARY DRIVE ASSY., REPLACE ONLY DRIVE GEAR WITH CLUTCH DRUM ASSY. |
1 |
| 5 | 259 570 | STUETZTELLER / INNER PLATE | 1 |
| 6 | 259 053 | BELAGLAMELLE 3,0 MM FRICTION PLATE 3,0 MM |
8 |
| 7 | 259 557 | INNENLAMELLE / CLUTCH PLATE 1 MM | 7 |
| 8 | 259 555 | STUETZLAMELLE / CLUTCH PLATE 1.5 MM | 1 |
| 9 | 259 775 | MITNEHMER / CLUTCH HUB | 1 |
| 10 | 245 320 | SICHERUNGSBLECH NA2O / TAB WASHER NA20 | 1 |
| 11 | 242 605 | SK-MUTTER M18X1.5 / HEX. NUT M18X1,5 TIGHTENING TORQUE 80 NM |
1 |
| 12 | 239 740 | KUPPL.FEDER DM15,7 D2,4 L39 CLUTCH SPRING 39 MM CHANGE SPRINGS ONLY SETWISE |
6 |
| 13 - 14 | 259 597 | DRUCKPLATTE KPL. / RETAINING PLATE ASSY., | 1 |
| 13 | 259 594 | DRUCKPLATTE / RETAINING PLATE | 1 |
| 14 | 232 180 | DRUCKLAGER 8X20X8,5 THRUST BEARING 8X20X8,5 |
1 |
| 15 | 945 750 | FEDERRING AS DIN 128 / LOCK WASHER A5 | 6 |
| 16 | 241 770 | SK-SCHRAUBE M5X25 DIN 933 HEX.SCREW M5X25 |
6 |
| 17 | 235 207 | ZWISCHENRAD KPL. / IDLER GEAR ASSY. 31 Τ. | 1 |
| 18 | 237 503 | STARTERWELLE / KICK START SHAFT | 1 |
| 19 | 944 468 | ANLAUFSCHEIBE 20,5/30/1 THRUST WASHER 20,5/30/1 |
3 |
| 20 | 945 660 | SICHERUNGSRING 20X1,2 DIN 471 SNAP RING 20X1,2 |
1 |
| 21 | 239 761 | KICKSTARTER FEDER / KICK START SPRING | 1 |
| 22 | 228 185 | SPERRAD RATCHET GEAR | 1 |
| 23 | 227 480 | ANLAUFSCHEIBE 20,2/25,5/1 THRUST WASHER 20,2/25,5/1 |
1 |
| 24 | 235 215 | STARTERRAD KPL. STARTER GEAR ASSY. 34 T. |
1 |
| 25 | 247 350 | DISTANZHUELSE 20,2/28/6 SPACER 20,2/28/6 |
1 |
| 26 | 247 450 | DISTANZRING 20,2/32/3,5 DISTANCE RING 20,2/32/3,5 |
1 |
| 27 - 33 | 248 895 | KICKSTARTERHEBEL KPL. KICK START LEVER ASSY. |
1 |
| 27 | 248 890 | KICKSTARTERHEBEL / KICK START LEVER | 1 |
| 28 - 30 | 248 809 | KICKSTARTERNABE KPL. / HUB ASSY. | 1 |
| 29 | 230 461 | O-RING 8,9-1,9 NBR 70-80 SH O-RING 8,9-1,9 |
1 |
| 30 | 945 845 | SICHERUNGSRING 15X1,5 DIN 471 CIRCLIP 15×1,5 |
1 |
| 31 | 239 535 | DRUCKFEDER DM 4,2 D1 L13 COMPRESSION SPRING 13 MM |
1 |
| 32 | 232 440 | KUGEL 7/32 III DIN 5401 / BALL 7/32 | 1 |
| 33 | 260 210 | MUFFE / RUBBER SLEEVE | 1 |
| 34 | 240 021 | SCHAFTSCHRAUBE M8X30 / CYL.SCREW M8X30 | 1 |
| 35 | LOCTITE ANTI-SEIZE 76710 LOCTITE ANTI-SEIZE 10 GR TO PREVENT METAL GALLING |
NA | |
| 36 | LOCTITE 221 VIOLET 10 CC LOW STRENGTH BOND |
NA |
Magneto Cover, Clutch Cover
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1 | 212 151 | ZUENDERDECKEL / MAGNETO COVER | 1 |
| 2 | 241 761 | ZYL SCHRAUBE M6X50 DIN 912 ALLEN SCREW M6X50 |
2 |
| 3 | 241 821 | ZYL SCHRAUBE M6X45 DIN 912 ALLEN SCREW M6X45 |
1 |
| 4 | 241 800 | VERSCHLUSSSCHRAUBE M18X1,5 PLUG SCREW M18X1.5 |
3 |
| 5-6 | 212 365 | KUPPLUNGSDECKEL KPL. CLUTCH COVER ASSY. |
1 |
| 6 | 949 030 | HR-KERBNAGEL 3X8 DIN 1476 / DRIVE PIN 3X8 | 1 |
| 7 | 230 355 | WD-RING BS 20X28X6 / OIL SEAL 20X28X6 | 1 |
| 8 | 232 150 | KUGEL 12 III DIN 5401 / BALL 12 MM | 3 |
| 9 | 259 945 | AUSRUECKTELLER KPL. / RELEASE CAM ASSY. | 1 |
| 10 | 240 315 | GEWINDESTIFT M8X22 ADJUSTMENT SCREW M8X22 |
1 |
| 11 | 942 670 | SK-MUTTER M8 SW 11 / HEX. NUT M8 | 1 |
| 12 | 239 901 | BLATTFEDER / FLAT SPRING | 1 |
| 13 | 240 560 | ZYL.SCHRAUBE M5X12 DIN 84 CYL. SCREW M5X12 |
1 |
| 14 | 239 635 | ZUGFEDER / SPRING | 1 |
| 15 | 241 811 | ZYL SCHRAUBE M6X35 DIN 912 ALLEN SCREW M6X35 |
6 |
| 16 | 241 816 | ZYL SCHRAUBE M6X40 DIN 912 ALLEN SCREW M6X4D |
2 |
| 17 | 830 890 | DICHTRING 6,2/8,9/1 GASKET RING 6,2/8,9/1 |
1 |
| 18 | 840 371 | ZYL.SCHRAUBE M6X11.5 ALLEN HEAD SCREW M6X11,5 FOR OIL LEVEL |
1 |
| 19 | 297 442 | KUPPLUNGSSEILZUG KPL. CLUTCH CABLE ASSY. |
1 |
| 20 | 297 495 | ROTAX-DECKELSCHILD MS / ROTAX LABEL | 2 |
| 21 | LOCTITE 221 VIOLET 10 CC LOW STRENGTH BOND |
NA |
Motoplat Magneto-Generator 6V 40/21/10W
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1-6 | 292 718 | MZ-GENERATOR 6V 40/21/10W MAGNETO GENERATOR 6V 40/21/10W |
1 |
| 1 | 264 885 | ANKERPLATTE / STATOR PLATE | 1 |
| 2 | 264 880 | ANKERSATZ / STATOR | 1 |
| 3 | 245 510 | FEDERSCHEIBE A4 DIN 137 SPRING WASHER A4 |
3 |
| 4 | 240 041 | ZYL.SCHRAUBE M4X26 DIN 84 ALLEN SCREW M4X26 |
3 |
| 5 | 264 898 | SCHWUNGRAD / FLYWHEEL, EXTRA LIGHT EXTRA LEICHT |
1 |
| 6 | 964 062 | STECKERSTIFT 3,96 / FASTON CONNECTOR 3,96 | 1 |
| 7 | 224 030 | KABELFIXIERUNG / CABLE HOLDER | 1 |
| 8 | 945 990 | FEDERSCHEIBE BS DIN 137 SPRING WASHER B5 |
2 |
| 9 | 241 841 | ZYL.SCHRAUBE M5X12 DIN 6912 ALLEN SCREW M5X12 |
2 |
| 10 | 260 347 | LEITUNGSTUELLE / CABLE GROMMET | 1 |
| 11-12 | 264 835 | ZUENDSPULE KPL. / IGNITION COIL ASSY. | 1 |
| 12 | 865 200 | ZUENDLEITUNGSSTECKER SPARK PLUG PROTECTOR |
1 |
| 13 | 899 920 | ZUENDKERZE 14 W3CC (W275T2) SPARK PLUG 14 W3CC (W275T2) |
1 |
| 14 | LOCTITE 221 VIOLET 10 CC LOW STRENGTH BOND |
NA | |
| 15 | LOCTITE 648 GRUEN LOCTITE 648 GREEN 6 CC HIGH STRENGTH BOND |
NA |
Repair Tools, Gasket Set
| ILL. NO. | PART NO. | DESCRIPTION | QTY. |
|---|---|---|---|
| 1- 12 | 277 784 | WERKZEUGSATZ / TOOL KIT | 1 |
| 1 | 876 195 | WERKZEUGTASCHE TOOL BAG | 1 |
| 2 | 277 825 | RINGSCHLUESSEL 22X24 RING WRENCH 22X24 MM |
1 |
| 3 | 276 065 | DOPPELMAULSCHLUESSEL 10X13 FORK WRENCH 10X13 ΜΜ |
1 |
| 4 | 277 411 | STECKSCHLUESSEL 17X21 SOCKET WRENCH 17X21 MM |
1 |
| 5 | 876 220 | STECKSCHLUESSEL 11X13 SOCKET WRENCH 11X13 MM |
1 |
| 6 | 276 040 | KONTERSCHLUESSEL / WRENCH 11MM FOR CLUTCH ADJUSTMENT |
1 |
| 7 | 277 790 | SECHSKANTSTIFTSCHLUESSEL 4 ALLEN HEAD KEY 4 |
1 |
| 8 | 876 360 | SK-STIFTSCHLUESSEL 5 / ALLEN HEAD KEY 5 | 1 |
| 9 | 277 810 | SECHSKANTSTIFTSCHLUESSEL 6 ALLEN HEAD KEY 6 |
1 |
| 10 | 277 840 | SCHRAUBENZIEHERGRIFF / SCREW DRIVER GRIP | 1 |
| 11 | 277 830 | SCHRAUBENZIEHEREINSATZ SCREWDRIVER BLADE-FLAT |
1 |
| 12 | 277 835 | KREUZSCHLITZKLINGE SCREW DRIVER BLADE-PHILLIPS |
1 |
| 13 | 277 850 | MONTAGESTEMPEL KPL. INSERTION JIG ASSY. FOR OIL SEAL 230 355, KICK-START SHAFT |
1 |
| 14 | 277 861 | MONTAGESTEMPEL KPL. INSERTION JIG ASSY. FOR OIL SEAL 230 395, MAIN SHAFT |
1 |
| 15 | 277 875 | MONTAGESTEMPEL KPL. INSERTION JIG ASSY. FOR OIL SEAL 230 425, CRANKSHAFT |
1 |
| 16 | 276 940 | MONTAGESTEMPEL KPL. / INSERTION JIG ASSY. FOR CRANKCASE RING |
1 |
| 17 | 276 705 | ABZIEHER KPL. M35×1,5 PULLER ASSY. M35X1,5 FOR FLYWHEEL |
1 |
| 18 | 241 965 | FIXIERSCHRAUBE M8X30 FIXATION SCREW M8X30 FOR CRANKSHAFT |
1 |
| 19 | 277 970 | FUEHRUNGSHUELSE / GUIDE SLEEVE FOR MAIN SHAFT |
1 |
| 20 | 276 915 | ABZIEHPLATTE / PLATE FOR PULLER FOR CRANKCASE HALF |
1 |
| 21 | 940 451 | ZYL SCHRAUBE M6X25 DIN 84 SLOTTED HEAD SCREW M6X25 |
3 |
| 22 | 276 920 | SCHUTZKAPPE / PROTECTION CAP FOR CRANKSHAFT |
1 |
| 23 | 277 917 | MONTAGEBOCK KPL. / TRESTLE ASSY. | 1 |
| 24 - 29 | 277 105 | MONTAGEBOCK-AUFNAHMESATZ INSERT KIT FOR TRESTLE ASSY. FOR ENGINE TYPE 124, 127, 244, 280 AND 406 |
1 |
| 24 | 277 100 | ADAPTER KPL. / ADAPTOR ASSY. | 1 |
| 25 | 940 590 | SK-SCHRAUBE M8X20 DIN 933 HEX.SCREW M8X20 |
1 |
| 26 | 250 311 | SCHEIBE 8,4 DIN 125 / WASHER 8,4 | 2 |
| 27 | 277 110 | AUFNAHMEBOLZEN / BOLT | 1 |
| 28 | 242 201 | SK-MUTTER M8 DIN 934 / HEX. NUT M8 | 1 |
| 29 | 847 160 | DISTANZHUELSE 10,5/24/15 SPACER 10,5/24/15 FOR ENGINE TYPE 127 |
1 |
| 30 - 31 | 277 160 | ABDRUECKPLATTE KPL. / PULLER PLATE ASSY., FOR CRANKSHAFT |
1 |
| 31 | 940 755 | SK-SCHRAUBE M16X1,5X150 DIN961 HEX. SCREW M16X1,5X150 |
1 |
| 32 - 36 | 276 360 | LAGERAUSZIEHER KPL. / PULLER ASSY. FOR BALL BEARING |
1 |
| 33 | 276 380 | AUSZIEHBOLZEN / BOLT M10 BOLT M10 |
1 |
| 34 | 276 370 | SPREIZHUELSE / EXTRACTOR SLEEVE FOR BALL BEARING 620317-40-12, CLUTCH SHAFT |
1 |
| 35 | 276 390 | ABSTUETZLEISTE / SUPPORT PLATE | 1 |
| 36 | 242 090 | SK-MUTTER M10 DIN 934 / HEX. NUT M10 | 2 |
| 37 | 277 885 | MITNEHMERFIXIERUNG CLUTCH HUB LOCKING TOOL |
1 |
| 38 | 876 976 | MONTAGERING / PISTON RING SPANNER 84 MM. TO MOUNT PISTON IN CYLINDER |
1 |
| 39 | 977 475 | RINGHAELFTE / RING HALF FOR BALL BEARING 6306, 30-72-19, CRANKSHAFT |
2 |
| 40 | 977 490 | RING / RING FOR RING HALF |
1 |
| 41 | 876 296 | ABZIEHER KPL. / PULLER ASSY FOR BALL BEARING |
1 |
| 42 | 940 755 | SK-SCHRAUBE M16X1,5X150 DIN961 HEX. SCREW M16X1.5X150 |
1 |
| 43 | 840 680 | ZYL SCHRAUBE M8X40 DIN 912 ALLEN SCREW M8X40 FOR PULLER |
2 |
| 44 | 277 180 | KUGELLAGERABZIEHER-GARNITUR BALL BEARING PULLER SET FOR BALL BEARING 6006,6203,6300,6007,6204,6301, 6302,6204E,6205,6303 AND 6304 |
1 |
| 45 - 46 | 877 015 | MONTAGEDORN KPL. CIRCLIP INSTALLATION TOOL ASSY. FOR PISTON PIN CIRCLIP 18 MM |
1 |
| 45 | 877 020 | MONTAGEHUELSE CIRCLIP INSTALLATION SLEEVE 18MM FOR PISTON PIN CIRCLIP 18 MM |
1 |
| 46 | 877 010 | MONTAGEDORN CIRCLIP INSTALLATION PUSHER 18MM FOR PISTON PIN CIRCLIP 18 MM |
1 |
