Lifetime 73729 Backboard & Rim Basketball System

Model 73729

Before you start:

• Decide where you would like to mount your system. A mounting kit is required for Roof and Wall mounts and is available through the Customer Service Department (see page 9).
• Recruit friends and family. Assembly should take 2 people about 2-3 hours to complete.

Mounting Kit not included*

*Backboard Brackets (included with the Lifetime® Universal Mounting Kit, sold separately) are required to complete the assembly as instructed in this manual.

Save this instruction in the event that the manufacturer has to be contacted for replacement parts.

Icon Legend

• ⚠️ Indicates special heed should be taken when reading.
• ? Indicates the parts to be used for a section.
• ?? Indicates no parts required for a specific section.
• ? Indicates the hardware to be used for a section.
• ?? Indicates no hardware required for a specific page.
• ?️ Indicates the tools to be used for a section.
• Indicates to use an electric drill for a specific step. ? Indicates not to use an electric drill.
• ⚙️ Indicates the use of a centerlock nut. A nut with this marking will require some effort to tighten. This hardware was designed with this feature in order to prevent loosening later.

Warnings & Notices

Safety Instructions

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operation and to reduce the risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

• If using a ladder during assembly, use extreme caution.
• Two capable adults are recommended for this operation.
• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

Section 1: Backboard to Rim Assembly

Hardware Required

Parts Required

Tools Required

1.1 Assemble Backboard Brackets

Before beginning this assembly, follow the instructions included with your Mounting Kit (or original basketball system if this is to replace an existing system) to assemble the Backboard Brackets. To ensure a good fit, use the U-Bolt (AOU) included with this system when assembling the brackets.

For further details, see page 9.

Backboard Brackets are included in the Mounting Kit (sold separately) and may vary from those shown here.

Lay the backboard on a table or bench. Insert the U-Bolt (AOU) through the upper part of the opening on the backside of the Backboard (AJI) as shown.

The Backboard Brackets shown here are provided with the Mounting Kit (sold separately) or with your original unit. The actual Brackets may vary, but the assembly steps still apply. See page 9 for more details.

The Backboard Brackets shown represent Lifetime Products® components and are for illustration purposes only. If using Brackets other than the Lifetime Products® models shown here, refer to the instructions provided with the Brackets.

1.2 Insert Carriage Bolts

Slide a Carriage Bolt (ABC) into the crimped slot in each backboard channel.

1.3 Attach Backboard Brackets

Bend the Backboard Brackets (not included) so the lower holes go over the Carriage Bolts. Lifetime® Backboard Brackets are designed to be bent by hand. Secure the Brackets to the Carriage Bolts through the lower of the two holes in the Bracket.

The Backboard Brackets shown here are not included with this system.

1.4 Install Push Nut on Axle

Use the 1/2" socket head from the socket-head wrench to press one Push Nut (AAQ) onto one end of the Axle (ABQ).

The Push Nut should rest about 1/4" from the end of the Axle. If the Push Nut slips on too far, continue sliding it to the other end of the Axle to remove it and try again.

1.5 Attach Rim to Backboard

Turn the backboard on its back and position the Rim (ALX) inside the Plastic Guard as shown. Slide the end of the Axle (ABQ) through the Rim and the Rim Pivot Bracket (APY). Press the Push Nut (AAQ) onto the end of the Axle. Use the 1/2" (13 mm) socket head to secure the Push Nut if needed.

1.6 Install Springs and Jam Nuts

Thread the Jam Nuts (AAV) as far as they will go on the ends of the U-Bolt. Then slide the Springs (AJW) into place and secure them with the hardware shown.

DO NOT COMPLETELY TIGHTEN THE FLANGE NUTS IN THIS STEP! Only tighten the Nuts until the Rim does not wobble. Tightening the Nuts will adjust the Rim tension.

1.7 Attach Rim Cover Plate

Attach the Rim Cover Plate (AMA) to the Rim.

1.8 Attach Center Frame Pad

Remove the plastic film from the Backboard (AJI), and attach the Center Frame Pad (AJQ) to the Backboard in the location shown with the hardware indicated. Make sure that the Center Frame Pad is oriented and centered on the metal piece of the Backboard.

1.9 Attach Corner Frame Pads

Attach the Corner Frame Pads (BAA and BAB) to the Backboard in the locations indicated with the hardware indicated.

1.10 Attach Net

Attach the Net (AKZ) to the Rim.

If a replacement Net is needed, please call the Customer Service Department. Nets are shorter than average to reduce the risk of entanglement.

Mounting the System

Mounting Kit Sold Separately

For mounting the Backboard & Rim Combo to a roof, wall, or existing pole mount that does not provide an extension, you must use a Mounting Kit designed for this purpose. Lifetime Products offers a Universal Mounting Kit, Model #9594, through the Customer Service Department. Figures A, B, and C show the Universal Extension Bracket mounted to a roof, a wall, and an existing pole. An Adjustable Height Mounting Kit, Model #1044, is also available (figure D).

Please refer to the information at the bottom of this page for ordering information.

Mounting Kit Types:

• FIG. A, ROOF MOUNT: Describes a roof mounting configuration.
• FIG. B, WALL MOUNT: Describes a wall mounting configuration.
• FIG. C, EXISTING POLE MOUNT: Describes mounting to an existing pole.
• FIG. D, ADJUSTABLE HEIGHT MOUNTING KIT: Describes an adjustable height mounting kit.

The Universal Mounting Kit and the Adjustable Height Mounting Kit are not included with this basketball system. See details below to order the kit from the Customer Service Department.

Product Information:

• Product Description: Universal Mounting Kit | Model #: 9594
• Product Description: Adjustable Height Mounting Kit | Model #: 1044

Call the Customer Service Department at 1.800.424.3865 for prices and shipping costs.

To place orders, use a Master Card or Visa and call the Customer Service Department, or send check or money order to:

LIFETIME PRODUCTS, INC.
P.O. BOX 160010
BLDG. D-11, FREEPORT CENTER
CLEARFIELD, UT 84016-0010

Maintenance

The life of your basketball system depends on many variables. The climate, exposure to corrosives such as salt, pesticides, or herbicides, and excessive use or misuse can all contribute to Pole failure, which may cause property damage or personal injury.

Check your basketball system frequently for loose hardware, excessive wear, and signs of corrosion. For safety reasons, and to prolong the life of your basketball system, you must take the following preventive measures:

1. Check all Nuts and Bolts. If any are loose, tighten them.
2. Check all parts for excessive wear and tear. If necessary, replace any parts that have been worn or damaged through usage. Contact the Customer Service Department for replacement parts.
3. Inspect the Warning Sticker on the Pole. If it is ripped, faded, or illegible, call the Customer Service Department to request a replacement Sticker.
4. Check all Pole sections for visible rust or chipped or cracked paint. If either are present, do the following:
   • Use an emery cloth to completely remove any rust or chipped paint.
   • Clean the area with a damp cloth and allow it to dry.
   • Apply two coats of a rust preventative, high gloss enamel paint to the area. Allow the paint to dry between coats.

IF RUST HAS PENETRATED THROUGH THE POLE ANYWHERE, REPLACE IT IMMEDIATELY!

Register Your Product

At Lifetime®, we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input is valuable to us.

• You can also opt in to receive new product notifications or promotions.
• In the unlikely event of a product recall or safety modification, your registration provides the information we need to notify you directly.
• Registration is fast, easy, and completely voluntary.

Lifetime's Promise to You:

Maintaining your privacy is our long-standing policy at Lifetime®. Lifetime® will not sell or provide your personal data to other third parties, or allow them to use your personal data for their own purposes.

We invite you to read our privacy policy at www.lifetime.com

REGISTER today!

Warranty

5-Year Limited Factory Warranty

THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE.

1. Lifetime basketball systems are warranted to the original purchaser to be free from defects in material or workmanship for a period of five years from the date of original retail purchase. The word “defects” is defined as imperfections that impair the use of the product. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective product. If the product is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory or distribution center are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the basketball system or its components are not covered under this warranty.
3. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use or hanging from the rim will void this warranty.
4. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
5. This product is not intended for institutional or commercial use; Lifetime Products, Inc. does not assume any liability for such use. Institutional or commercial use will void the warranty.
6. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
7. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for use to extent permitted by Federal and state law. Neither Lifetime Products, Inc., nor any representative assumes any other liability in connection with this product. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

PLEASE INCLUDE YOUR DATED SALES RECEIPT AND PHOTOGRAPHS OF DAMAGED PARTS.

REPORT PRODUCT DEFECTS IN WRITING TO:
Lifetime Products, Inc., PO Box 160010 Clearfield, UT 84016-0010
or call 1-800-225-3865 M-F 7 a.m. to 5 p.m. MST.

REGISTER YOUR PRODUCT FOR QUICKER CUSTOMER SERVICE.
Visit www.lifetime.com or call 1-800-225-3865 to register your product today.

FOR INTERNATIONAL WARRANTY CLAIMS:
All warranty claims must be accompanied by a sales receipt. Report all warranty claims in writing to your regional sales support representative. Please include your dated sales receipt and photographs of damaged parts.
To Identify the representative for your region, please visit: www.lifetime.com/international