STELPRO Built-in Electronic Thermostat
Owner's Guide and Installation Manual
For Brava and Prima Electric Baseboards
Model Numbers: SIBTE12C, SIBTE12F, SIBTE13C, SIBTE13F
Contact: 1-844-STELPRO | www.stelpro.com
ISO 9001:2015 Certified
Important Instructions
WARNING: HIGH VOLTAGE. Turn off the power supply before installation and maintenance.
Before installing or using this product, read and understand these instructions. STELPRO DESIGN INC. cannot be held responsible for any issues arising from failure to follow these instructions. Warranty will be void if instructions are not followed. Non-compliance may result in bodily harm, property damage, serious injury, or fatal electric shock.
The thermostat must be installed by a certified electrician.
SAVE THESE INSTRUCTIONS
Technical Specifications
| PRODUCT CODE | VERSION (°C OR °F) | SUPPLY VOLTAGE (VAC) | LOAD (W) | VOLTAGE RATING OVERVOLTAGE CATEGORY |
|---|---|---|---|---|
| SIBTE12C | °C | 120-240 | 300-2500 | II (1500V) |
| SIBTE12F | °F | |||
| SIBTE13C | °C | 277-347 | 300-2500 | III (2500V) |
| SIBTE13F | °F |
Built-in control device: Thermistor used as a sensor, carries no charging current.
Class: A software.
Enclosure protection rating: IP20.
Power supply type: Device designed for alternating current only.
Load control type: Resistive.
Action: Type 1.Y.
Pollution level: 2.
Frequency: 60 Hz.
Overload protection device external to the control: Circuit breaker (refer to local electrical code).
Operating temperature: -20°C to 65°C (-4°F to 149°F).
Storage temperature: -40°C to 65°C (-40°F to 149°F).
Installation
1. Prepare the Baseboard
WARNING: Turn off the power supply. Do not install the thermostat in a position other than that indicated in this guide.
- Choose which side of the baseboard to install the thermostat. The connection must be made in the same junction box as the power supply.
- Remove the front panel. Refer to the baseboard instructions for more details.
- Unscrew the front cover of the junction box [A] and remove it.
- Remove the knockouts [B] with a hammer and a screwdriver.
Diagram Description: Illustrates the baseboard interior, showing the junction box cover labeled [A] and knockouts labeled [B]. Separate views are provided for BRAVA and PRIMA models.
2. Assemble the Thermostat
- Attach the thermostat using the screws provided.
- To ensure proper grounding and heat transfer, make sure the thermostat is screwed in securely and is in contact with the junction box cover.
Diagram Description: Shows the thermostat being attached to the junction box cover using screws. Views for both BRAVA and PRIMA models are presented.
3. Connect the Power Supply Wires
Complete the thermostat's electrical connection according to one of the diagrams below. Tighten the wires securely in the supplied connection caps.
WARNING: Be sure to connect the wire colours as shown in the diagrams when making electrical connections.
Diagram Description: Depicts the wiring connections for the thermostat. The BRAVA model shows YELLOW, RED, and BLACK wires. The PRIMA model shows RED, YELLOW, and BLACK wires.
4. Install the Temperature Sensor
Install the temperature sensor [A] as shown, making sure it is firmly seated at the bottom of the groove.
Diagram Description: Illustrates the installation of the temperature sensor labeled [A] into the baseboard. Views for BRAVA and PRIMA models are shown.
5. Install the Interface
- Make sure surfaces are clean and dry. Position the interface so that the numbers face in the correct direction, as shown.
- Remove the adhesive protection on the back of the interface.
- Insert the connector into the opening. Clip the interface into place and press firmly so that the adhesive sticks to the surface.
- Clip the interface connector into the thermostat connector.
- Push all the wires into the junction box while closing it. Make sure the wires and tape are not tangled.
- Screw the junction box cover back on, then replace the front panel.
- Restore the power supply.
Diagram Description: Shows the process of installing the interface, including connecting the interface connector to the thermostat connector and securing the junction box cover. Steps 3, 4, and 5 are visually represented.
Operating Instructions
3 Buttons to Control the Temperature
Use the three buttons to adjust the setpoint temperature:
- Press to lower the setpoint temperature by 1°.
- Press (or for Celsius) to set the setpoint temperature.
- Press to raise the setpoint temperature by 1°.
Diagram Description: Displays the thermostat interface with three control buttons labeled -1°, 70°/20°, and +1°. Indicator lights are also shown. A view for Model C (Celsius) is included.
Initial Setting
Once installation is complete, configure your thermostat according to your baseboard model.
| BASEBOARDS | MODEL F (Fahrenheit) | MODEL C (Celsius) | INDICATOR LIGHTS |
|---|---|---|---|
| BRAVA* | Press simultaneously (3 sec.) | Press simultaneously (3 sec.) | Purple |
| PRIMA | Press simultaneously (3 sec.) | Press simultaneously (3 sec.) | Light blue |
* By default, the thermostat is set up for the BRAVA baseboard.
Indicator Lights
The indicator lights provide feedback on your comfort choices and other advanced features.
| COLOUR | DESCRIPTION | MODEL F (Fahrenheit) | MODEL C (Celsius) |
|---|---|---|---|
| BLUE | Freeze protection | 41°F | 5°C |
| GREEN | Energy saving | 42°F to 66°F | 6°C to 19°C |
| GREEN TO ORANGE | Eco-comfort balance | 67°F to 74°F | 20°C to 23°C |
| RED | Optimal comfort | 75°F to 86°F | 24°C to 30°C |
| FLASHING RED | The baseboard has overheated, and heating has been switched off. After four minutes, the indicator lights will turn off. Heating will be restored. If the indicator lights flash repeatedly, make sure nothing is obstructing the baseboard. Otherwise, contact STELPRO. | ||
| FLASHING YELLOW | The baseboard isn't operating due to a problem with the temperature sensor. Please contact STELPRO. | ||
| FLASHING WHITE | Lock/unlock feature. See the section below. | ||
Adjusting the Temperature
Here are some examples of how to use the three buttons on the thermostat to adjust the setpoint temperature.
| DESIRED TEMPERATURE | PRESS | INDICATOR LIGHTS |
|---|---|---|
| 72 °F* | Press then | Orange |
| 67 °F* | Press then then | Green |
| 41 °F* Freeze protection | Press (3 sec.) | Blue |
* Celsius version on the back.
Lock/Unlock Feature
| ACTION | PRESS | INDICATOR LIGHTS |
|---|---|---|
| LOCK | Press simultaneously | After 3 sec., 3 white flashes |
| UNLOCK | Press (3 sec.) | After 3 sec., display of the current setpoint color |
When an attempt is made to change the setpoint while in lock mode, the indicator lights will flash white three times.
Limited STELPRO Warranty
Limited three-year warranty. See details on www.stelpro.com.
What's in the Box
- One (1) thermostat
- One (1) control interface
- Two (2) screws
- Three (3) twist-on wire connector
Material Required
- Hammer
- #2 Phillips or #2 Robertson screwdriver
