Liebherr NoFrost Combined Refrigerator-Freezers

Important Notes

Please Read and Follow these Instructions

These instructions contain Danger, Warning, and Caution notes. This information is important for safe and efficient installation and operation. Always read and comply with all Danger, Warning, and Caution notes!

? DANGER: Danger indicates a hazard that will cause serious injury or death if precautions are not followed.

? WARNING: Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

? CAUTION: Caution indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

? IMPORTANT: This indicates information that is especially relevant to a problem-free installation and operation.

Note to the Installer

It is very important to follow the instructions in this manual to ensure proper installation and operation of the unit. Before installing the unit, be sure to thoroughly read and understand all of the information in this manual.

? WARNING! Electrocution hazard. Do not connect to the electrical outlet before the installation is completed.

R600a Refrigerant

? WARNING! The refrigerant contained within the appliance R600a is environmentally friendly, but flammable. Leaking refrigerant can ignite.

To prevent possible ignition, follow the warnings below:

• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• Do not damage the refrigerant circuit.
• Component parts and power cords shall be replaced with like components performed by factory authorized service personnel only.

Safety

Disposal of Old Appliance

? DANGER! Risk of child entrapment. Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous – even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before you discard old appliances:

• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.
• Cut off the power cable from the discarded refrigerator. Discard separately from the refrigerator.
• Be sure to follow your local requirements for disposal of appliances. Contact the trash collection agency in your area for additional information.

Disposal of Carton

The packaging is designed to protect the appliance and individual components during moving and is made of recyclable materials.

? WARNING! Keep packaging materials away from children. Polythene sheets and bags can cause suffocation!

Please recycle packaging material where facilities are available.

Electrical Safety

Connect this appliance to a 15 amp or 20 amp, 110-120 VAC, circuit which is grounded and protected by a circuit breaker or fuse. We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of interruption to the appliance.

This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards. Where a two-prong wall receptacle is encountered, contact a qualified electrician and have it replaced with a properly grounded three-prong receptacle in accordance with all local codes and ordinances.

Disconnect power before installing optional Side By Side Kit.

? WARNING! Electrocution hazard. Electrical grounding required.

• Do not remove the round grounding prong from the plug. [Diagram shows a standard three-prong plug with two flat parallel pins and a round grounding pin.]
• Do not use extension cords or ungrounded (two prong) adapters. [Diagram shows a two-prong adapter, which converts a three-prong outlet to a two-prong receptacle.]
• Do not use a power cord that is frayed or damaged. [Diagram shows a power cord with visible damage to its outer insulation, exposing wires.]
• Do not use a power strip. [Diagram shows a power strip.]

Failure to follow these instructions may result in fire, electrical shock or death.

Blocking for Safety

? WARNING! To avoid a hazard due to instability of the appliance, it must be fixed in accordance with the instructions.

Planning Information

Appliance Dimensions

The overall height of the appliance can be increased by a maximum of 5/8 inch (see Leveling the Appliance).

Cabinet Opening Dimensions

The appliance can be used freestanding or semi built-in. If semi built-in, please consider the cabinet opening dimensions.

For CS 1400 R, CS 1400 PC:

For CS 1410:

IMPORTANT: The power plug must be easily accessible so that the appliance can be disconnected from the mains quickly in an emergency. It must not be behind the back of the appliance.

Clearance on the back must be 2 inches (51 mm).

NOTE: If the gap between the rear of the appliance and the wall is less than 2 inches (51 mm), the power consumption level may increase.

Installation

Unit Venting

Do not restrict the air flow.

The ventilation opening can either be directly over the appliance (1), above the cabinet and below the ceiling (2), or through a vent installed in a soffit (3).

IMPORTANT: The clear ventilation cross-section must be at least 31 in² (200 cm²) from the lower ventilation opening right to the upper one.

The section below the freezer door and the floor must not be covered.

Leveling the Appliance

The height can be adjusted in front by twisting the leveling feet.

Twist the adjusting bolt to set up the back of the appliance. Align the appliance with the sides of kitchen cabinets by adjusting leveling feet and the supports.

IMPORTANT: After final installation, this screw must be turned down until it has proper floor contact to support the hinge bracket.

? CAUTION: Risk of injury or damage from the appliance tipping or the door falling open! If the additional adjustable foot on the base support is not correctly positioned on the floor, there is a risk of the door falling open or the appliance tipping. This can lead to injury or property damage.

• Unscrew the additional adjustable foot on the support until it reaches the floor.
• Then turn it another 90°.

Blocking for Safety

Mounting the anti tipping device

? WARNING! Tip over hazard! The anti tipping brackets must be mounted to prevent the appliance from tipping when the fully stocked door is opened.

IMPORTANT: Be sure that there is no plumbing or electrical wiring located in this area which screws or drills could damage.

1. Mark the center of the appliance on the back wall.
2. Mount the anti tipping brackets within the given area.

IMPORTANT: The screws for fastening the anti-tip device are not supplied with the appliance. Appropriate screws must be used for the material (wood, concrete, etc.) in which the safety device is mounted.

Reversing Door Hinges

Changing Over Door Hinges - CS 1400 R, CS 1410

Door hinges should only be changed by a trained expert. Changing over the door hinges requires two people.

1. Open the top door, pry off the door cover and pivot to the left. [Diagram shows this action.]
2. Let the door cover hang down. [Diagram shows the cover hanging.]
3. Slide the red safety bracket over the hinge. [Diagram shows this action.]
4. Pull the left-hand side of the cover approximately 1/4 inch (6 mm) towards you. [Diagram shows this action.]
5. Remove the pin. [Diagram shows pin removal.]
6. Open the top door wide and remove covers. [Diagram shows this action.]
7. Remove the cover. [Diagram shows cover removal.]

IMPORTANT: The two knobs on the safety bracket must be fully inserted into the marked openings on the hinge.

8. Remove the cover from the upper door mounting and unscrew the door. [Diagram shows this action.]
9. Transfer the fastener for the soft stop mechanism to the opposite side. [Diagram shows this action.]
10. Transfer the cover plate to the opposite side. [Diagram shows this action.]
11. Remove the cover. [Diagram shows cover removal.]
12. Open the bottom door, pry off the door cover. [Diagram shows this action.]
13. Pivot the door cover to the left. [Diagram shows this action.]
14. Slide the red safety bracket over the hinge. [Diagram shows this action.]
15. Remove the pin. [Diagram shows pin removal.]
16. Open the bottom door wide and remove the cover. [Diagram shows this action.]
17. Pull out the middle hinge pin. [Diagram shows this action.]
18. Remove the bottom door. [Diagram shows this action.]
19. Unscrew the hinge bracket. [Diagram shows this action.]
20. Transfer the cover plate to the opposite side. [Diagram shows this action.]
21. Turn the hinge bracket through 180° and screw into place. [Diagram shows this action.]
22. Remove the hinge bushing, turn through 180° and re-fit. [Diagram shows this action.]
23. Tilt the appliance slightly backwards and unscrew the adjustable foot. [Diagram shows this action.]
24. Remove the hinge pin. [Diagram shows this action.]
25. Unscrew the hinge bracket. [Diagram shows this action.]
26. Transfer the fastener for the soft stop mechanism on the hinge bracket to the opposite side. [Diagram shows this action.]
27. Transfer the cover to the opposite side. [Diagram shows this action.]
28. Transfer the cover plate to the opposite side. [Diagram shows this action.]
29. Screw the hinge bracket into place. [Diagram shows this action.]
30. Tilt the appliance slightly backwards, insert the pin and attach using the adjustable foot. [Diagram shows this action.]
31. Remove screw. [Diagram shows this action.]
32. Pivot the soft stop mechanism outwards on the right, pull to the right and remove. [Diagram shows this action.]
33. Slide the spacer to the left and remove. [Diagram shows this action.]
34. Release the pressure plates at the front (1) and pull them backwards to remove (2). [Diagram shows this action.]
35. Transfer the door handle and plugs to the opposite side. [Diagram shows this action.]
36. Transfer panels of both door covers to the opposite side. [Diagram shows this action.]
37. Turn the spacer through 180° and re-fit on the opposite side. [Diagram shows this action.]
38. Turn the soft stop mechanism through 180° and re-fit on the opposite side. Then secure both parts with screws. [Diagram shows this action.]
39. Suspend the bottom door on the hinge pin. [Diagram shows this action.]

IMPORTANT: The door must now be held secure by another person.

40. Insert the middle hinge pin. [Diagram shows this action.]
41. Slide the door cover over the soft stop mechanism hinge. [Diagram shows this action.]
42. Move the soft stop mechanism hinge to the fastener and insert the pin. [Diagram shows this action.]
43. Remove the red safety bracket. [Diagram shows this action.]
44. Pivot the door cover to the left and click into place on the door. [Diagram shows this action.]
45. Click the cover into place. [Diagram shows this action.]
46. Using a screwdriver, push out the hinge from underneath and remove it from the door. [Diagram shows this action.]
47. Using a screwdriver, push out the plug from underneath and transfer it to the opposite side. [Diagram shows this action.]
48. Insert the hinge. [Diagram shows this action.]
49. Suspend the top door on the hinge pin. For this, the door must be open at least 90°. [Diagram shows this action.]

IMPORTANT: The door must now be held secure by another person.

50. Secure the door with screws and click the cover into place. [Diagram shows this action.]
51. Click the cover into place. [Diagram shows this action.]
52. Slide the door cover over the soft stop mechanism hinge. [Diagram shows this action.]
53. Pull the right-hand side of the cover approximately 1/4 inch (6 mm) towards you. [Diagram shows this action.]
54. Move the soft stop mechanism hinge to the fastener and insert the pin. [Diagram shows this action.]
55. Remove the red safety bracket. [Diagram shows this action.]
56. Pivot the door cover to the left and click into place on the door. [Diagram shows this action.]
57. Click the cover into place. [Diagram shows this action.]
58. Place the appliance in its final position at the place of installation. Extend the adjustable foot at the bottom hinge bracket until it rests on the floor and then make a further 90° turn. [Diagram shows this action.]

Changing Over Door Hinges - CS 1400 PC

Door hinges should only be changed by a trained expert. Changing over the door hinges requires two people.

1. Remove the cover from the upper door mounting and unscrew the door. [Diagram shows this action.]
2. Transfer the cover plate to the opposite side. [Diagram shows this action.]

IMPORTANT: The door must now be held secure by another person.

3. Pull out the middle hinge pin. [Diagram shows this action.]
4. Remove the bottom door. [Diagram shows this action.]
5. Unscrew the hinge bracket. [Diagram shows this action.]
6. Transfer the cover plate to the opposite side. [Diagram shows this action.]
7. Turn the hinge bracket through 180° and screw into place. [Diagram shows this action.]
8. Remove the hinge bushing, turn through 180° and re-fit. [Diagram shows this action.]
9. Tilt the appliance slightly backwards and unscrew the adjustable foot. [Diagram shows this action.]
10. Remove the hinge pin. [Diagram shows this action.]
11. Unscrew the hinge bracket. [Diagram shows this action.]
12. Transfer the hinge component on the hinge bracket to the opposite side. [Diagram shows this action.]
13. Transfer the cover to the opposite side. [Diagram shows this action.]
14. Transfer the cover plate to the opposite side. [Diagram shows this action.]
15. Screw the hinge bracket into place. [Diagram shows this action.]
16. Tilt the appliance slightly backwards, insert the pin and attach using the adjustable foot. [Diagram shows this action.]

Both doors

16. Release the pressure plates at the front (1) and pull them backwards to remove (2). [Diagram shows this action.]
17. Transfer the door handle and plugs to the opposite side. [Diagram shows this action.]

Both doors

18. Transfer the spring clip to the opposite side. [Diagram shows this action.]
19. Suspend the bottom door on the hinge pin. [Diagram shows this action.]

IMPORTANT: The door must now be held secure by another person.

20. Insert the middle hinge pin. [Diagram shows this action.]
21. Using a screwdriver, push out the hinge and remove it from the door. [Diagram shows this action.]
22. Using a screwdriver, push out the plug and transfer it to the opposite side. [Diagram shows this action.]
23. Insert the hinge. [Diagram shows this action.]
24. Suspend the top door on the hinge pin. For this, the door must be open at least 90°. [Diagram shows this action.]
25. Secure the door with screws and click the cover into place. [Diagram shows this action.]
26. Place the appliance in its final position at the place of installation. Extend the adjustable foot at the bottom hinge bracket until it rests on the floor and then make a further 90° turn. [Diagram shows this action.]

Service Information

For Service in the U.S.

Liebherr Service Center

Toll Free: 1-866-LIEBHER or 1-866-543-2437

Email: Service-appliances.us@liebherr.com

PlusOne Solutions, Inc.

3501 Quadrangle Blvd, Suite 120

Orlando, FL 32817

For Service in Canada

Liebherr Service Center

Toll Free: 1-888-LIEBHER or 1-888-543-2437

www.euro-parts.ca

EURO-PARTS CANADA

39822 Belgrave Road

Belgrave, Ontario, N0G 1E0

Phone: (519) 357-3320

Fax: (519) 357-1326

Visit us online: www.liebherr-appliances.com