Miele Fully Integrated Dishwasher Installation Guide

Important Information Before Installation

Please observe this installation sheet and read the operating instruction manual supplied with the appliance before it is installed or used for the first time. This will protect you and prevent damage to your appliance.

General Safety and Installation Precautions:

• ⚠️ Risk of damage or fire hazard.
• ⚠️ Do not use a cordless screwdriver; risk of damage.
• ⚠️ Warning: Danger of being cut.
• ❗ Check connection data.
• ⚙️ Screw the feet in before moving the dishwasher.
• ⚙️ After fitting the front panel to the door, the door springs must be set equally on both sides.
• ? Venting the water drain: If the on-site drainage connection is situated lower than the guide path for the lower basket rollers in the open door, the drainage system must be vented.

Tools and Accessories

The tools required depend on the specific model. Optional accessories may be available for purchase.

Tools required depend on model. Optional accessories.

Installation Steps

Step 1: Mounting Brackets

Attach mounting brackets to the cabinet sides using screws (e.g., 4x20, Ø2.0).

Step 2: Appliance Positioning

Position the dishwasher within the cabinet opening. Secure the appliance to the cabinet using appropriate fixings.

Step 3: Adjusting Feet

Adjust the appliance feet ⬆️⬇️ to ensure it is level and stable before moving it into its final position. The adjustable feet allow for height and tilt correction.

Step 4: Door Spring Adjustment

After mounting the front panel to the door, ensure the door springs are adjusted equally on both sides for proper door operation.

Step 5: Venting Water Drain

Venting the water drain. This step is necessary if the on-site drainage connection is lower than the guide path for the lower basket rollers in the open door. Ensure the drainage system is properly vented.

Step 6: Tools and Hardware

Overview of tools and hardware potentially required for installation. This may include screwdrivers (e.g., T20), screws of various sizes (e.g., 4x15, 4x20, 4x27), and other small parts.

Step 7: Optional Accessories

Illustration of optional accessories that can be purchased separately.

Step 8: Installation Space Dimensions

Installation space dimensions. Ensure the cabinet opening meets the specified height (X = 760-770 mm) and width (Y = 805-815 mm).

Step 9: Securing Appliance

Attach side panels or secure the appliance to the cabinet structure using screws (e.g., 4x20, Ø2.0).

Step 10: Hose and Electrical Connections

Connect the water inlet hose, drain hose, and electrical supply. Ensure all connections are secure.

Step 11: Securing to Worktop

Secure the appliance to the worktop or adjacent cabinets using the provided fixings.

Step 12: Attaching Front Panel

Attach the main front panel to the appliance door. This involves aligning and securing the panel.

Step 13: Handle Installation

Attach the handle to the front panel. Ensure it is firmly secured.

Step 14: Door Adjustment

Adjust the door hinges and/or springs to ensure the door opens and closes smoothly and aligns correctly.

Step 15: Kick Plate Installation

Install the kick plate or bottom trim at the base of the appliance.

Step 16: Drain Hose Connection

Connect the drain hose to the household waste pipe. Ensure a secure and watertight connection.

Step 17: Water Inlet Connection

Connect the water inlet hose to the cold or hot water supply tap. Ensure a secure connection.

Step 18: Electrical Connection

Connect the appliance to the electrical supply. Follow local electrical regulations.

Step 19: Securing to Worktop Underside

Secure the appliance to the underside of the worktop using the provided brackets or fixings.

Step 20: Insulation Installation

Install any provided insulation material around the appliance, as indicated.

Step 21: Inner Door Panel Attachment

Attach the inner door panel or decorative panel to the appliance door.

Step 22: Final Door Adjustments

Perform final adjustments to the door, ensuring it is properly aligned and operates smoothly.

Step 23: Bottom Panel Installation

Install the bottom panel or kick plate at the base of the appliance.

Step 24: Dimension Verification

Verify all installation dimensions and clearances are correct according to the specifications.

Step 25: Final Checks

Final checks of all connections and the appliance's stability before use.

Step 26: Water Connection Detail

Detailed view of the water inlet connection. Ensure the hose is correctly attached to the appliance and the water supply.

Step 27: Drain Connection Detail

Detailed view of the drain hose connection. The connection point typically requires a Ø22 mm fitting. Ensure the hose is securely connected to the waste pipe.

Step 28: Electrical Connection Detail

Detailed view of the electrical connection. Ensure proper grounding and adherence to electrical safety standards.

Step 29: Final Appliance Placement

Final placement of the dishwasher within the installed cabinet. Ensure it is stable and correctly aligned.