Wyze Room Sensor Quick Start Guide

Welcome to Wyze

Thank you for getting your hands on a Wyze Room Sensor. If this is your first Wyze product, welcome to the Wyze family! You have committed to a better, more connected lifestyle. This guide will help you get things set up.

Please read this guide carefully before setting up the device and keep it in a safe place for future reference.

In the Box

• Wyze Room Sensor x 1
• Base x 1
• Adhesive Pad x 1
• AAA Alkaline Battery x 2
• Quick Start Guide x 1

Display Screen Guide

The sensor display shows:

• Bluetooth indicator
• Battery Level indicator
• Temperature reading
• Humidity reading
• Comfort Level indicator
• Motion Detector status
• PIR Motion Sensor status

Combinations

The Wyze Room Sensor works with the Wyze Thermostat.

Mounting options include:

• On the wall
• On the stand

Setup

1. Insert the included batteries into the sensor's battery compartment.
2. Download the Wyze app and sign in to your Wyze account. Tap on your Wyze Thermostat in the app, then tap the pill icon at the top.
3. Tap the "+" plus icon to add your sensor. Follow the in-app instructions to finish setup.
4. Mount the room sensor at least 5 feet (1.5 meters) above the ground. To prevent signal shielding, do not mount the sensor on or near metallic surfaces. Ensure the PIR Motion Sensor is not blocked.
5. You're all set! Explore your new room sensor's features in the Wyze app.

Important: Do not place the sensor in direct sunlight, near windows, or near vents.

Comfort Level

The sensor indicates comfort levels based on temperature (T) and humidity (H):

• Ideal: 66℉ ≤ T ≤ 80℉ and 20% ≤ H ≤ 85%
• Too Warm/Humid: T > 80℉ and H > 85%
• Too Cold/Dry: T < 66℉ and H < 20%

Low Battery Alert

Replace the battery when the battery level is low. The battery level is displayed at the top of the sensor's screen.

Reset/Connectivity Button

Single Press: Used to set up the sensor.

Press and Hold: To reset the sensor, press and hold the reset button for 5 seconds.

Restrictions and Warnings

Restrictions

• Do not ingest battery. Risk of chemical burn. Keep batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. Seek immediate medical attention if a battery is swallowed.
• Risk of explosion if the battery is replaced by an incorrect type.
• Do not place the sensor in direct sunlight.
• The Wyze Room Sensor is not weatherproof or IP rated and is not intended for outdoor use.
• If the equipment is used in a manner not specified by the manufacturer, its protection may be impaired.
• Do not operate in conditions above 90% humidity, as this can cause condensation, icing, or fog, leading to damage.

Specifications

• Model: WRSENSOR
• Bluetooth: BLE 4.2
• Display: LCD
• Input: DC2.5-3V
• Dimensions: 80 mm x 40 mm x 12.4 mm
• Weight: 2.1 oz (60 g)
• Battery Type: AAA Alkaline Battery x 2
• Battery Life: 1 year
• Operating Temperature: 20°F - 122°F (-6°C - 50°C)
• Operating Humidity: 0% - 90% RH
• Storage Temperature: 20°F - 122°F (-6°C - 50°C)
• Storage Humidity: 0% - 90% RH
• PIR Motion Sensor Range: 17 ft

Regulatory Information

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISEDC Radiation Exposure Statement

This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

ISEDC RSS Warning

This device complies with ISEDC licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Need Help?

Contact the Wyze Support Team at https://wyze.com/support

Join the Wyze Community at https://wyze.com/community

Scan the QR code for more information.

Disclaimer

The products, accessories, user interfaces, etc. illustrated in this guide are intended for reference only. Due to product updates, the actual product and the illustrations in this guide may vary.