Wyze Leak Sensor Quick Start Guide

Welcome to Wyze

Small and flexible, our Wyze Leak Sensors were designed with a modern home in mind. Place anywhere to help ensure that your house is protected against unwanted leaks. Included in the bundle is a leak sensor probe that can reach places that our leak sensor cannot. Best of all, it's smart enough to tell whether the body or the sensor probe is detecting the leak.

In the Box

• Wyze Leak Sensor × 3
• CR2450 Battery x 3
• Wyze Leak Sensor Probe x 1
• Quick Start Guide x 1

Activation

To use the Wyze Leak Sensor, you will first need to set up your Wyze Sense Hub (sold separately). The Wyze Leak Sensor Probe can be connected to any Wyze Leak Sensor through the connection port.

Setup

1. Download the Wyze app and sign in or create an account.

2. To add your device to a previously installed system, open the Wyze app and tap the + sign on the top-left corner of the Home tab. Tap Add Device > Sensors > Wyze Leak Sensor. Follow the instructions in the Wyze app to complete installation and setup.

3. If you haven't already set up your Wyze Sense Hub, tap the Home Monitoring tab in the Wyze app. When your Home Monitoring license is activated, tap Start Setup. This will guide you through the installation process.

   Not seeing this screen? Go to services.wyze.com to activate your subscription.

4. Remove the plastic battery tab. Then press and hold the reset button on the side until the status light on the top of the leak sensor starts flashing.
5. In the Wyze app, name your sensor when prompted.
6. If you want to attach the leak sensor probe to the sensor, just connect it via the connection port. The leak sensor will automatically recognize the sensor probe.
7. Place your leak sensor or the sensor probe in the location you want to use it in.

Specifications

• Model: WSWL1
• Battery: CR2450
• Dimensions: 48 mm x 48 mm x 25 mm
• Battery Life: 1.5 years based on normal usage
• Mounting Method: Ground
• Range: 500ft
• Operation Temperature: 32°F-104°F (0°C-40°C)
• Operation Humidity: 85% at 86°F (30°C)
• Weather Resistance: IP67 (Indoor-use only)

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ISED Radiation Exposure Statement

This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Cet appareil est conforme aux limites d'exposition de rayonnement RF ISED établies pour un environnement non contrôlé. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.

ISED RSS Warning

This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Need Help?

Contact our support team: https://wyze.com/support

Join our Community: https://wyze.com/community

Scan the QR code to learn more.

User Manual Version: 1.0

Model: WSWL1

Specifications: WSWL1-KSZP01

Product Name: Wyze Leak Sensor (3-pack) Manual

Printing Color: CMYK

Material: 105g Matte Copper Paper

Finished Size: 70*68mm

Special Process: Folding, Oil Coating

Designed by: Yu Shuyuan

Approved by: Sample