HOMCOM IN221100110V01_GL Office Chair
Assembly and Safety Instructions
Important Information
EN: IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
FR: IMPORTANT: A LIRE ATTENTIVEMENT ET À CONSERVER POUR CONSULTATION ULTÉRIEURE.
ES: IMPORTANTE, LEA Y GUARDE PARA FUTURAS REFERENCIAS.
PT: IMPORTANTE, RETER PARA REFERÊNCIA FUTURA: LEIA ATENTAMENTE.
DE: WICHTIG! SORGFÄLTIG LESEN UND FÜR SPÄTERES NACHSCHLAGEN AUFBEWAHREN.
IT: IMPORTANTE! CONSERVARE IL PRESENTE MANUALE PER FUTURO RIFERIMENTO E LEGGERLO ATTENTAMENTE.
PL: WAŻNE, ZACHOWAĆ DO WYKORZYSTANIA W PRZYSZŁOŚCI: PRZECZYTAĆ UWAŻNIE.
RO: IMPORTANT, PĂSTRAŢI PENTRU REFERINȚE VIITOARE: CITIȚI CU ATENȚIE.
Estimated assembly time: ⏱️ 20 Minutes. Steps: 3.
Safety Information
- Intended Use: This product is intended for indoor use only, for work and study.
- Weight Distribution: To prevent the chair from falling, ensure weight is evenly distributed.
- Preparation: Remove all parts from the box and verify all parts are included before assembly.
- Posture: Keep feet on the floor and do not press your head against the headrest when reclining.
- Backrest Adjustment: Ensure fingers are safe and out of harm's way when adjusting the backrest.
- Handling: To avoid damage, never pull the chair quickly or forcefully indoors.
- Purpose: This chair is designed for sitting only. Do not use it as a base or ladder. Do not sit on the armrests.
- Capacity: This chair is designed for one person at a time.
- Damaged Parts: If any parts are missing, damaged, or worn, stop using the product immediately.
- Sunlight Exposure: Avoid direct sunlight on the chair to prevent plastic components from becoming brittle.
- Wheel Recommendations:
- For carpet: rigid nylon wheels or wheels with gears.
- For hard flooring: PU wheels or rubber wheels (avoid metal wheels to prevent scratching).
- Assembly Hazard: Be aware of crushing and cutting hazards during assembly.
- Manufacturer Liability: The manufacturer declines all responsibility for damages due to improper installation or environmental factors.
- Height Adjustment Warning: ⚠️ Only trained personnel may replace or repair components for height adjustment of seating furniture with energy storage.
Maintenance Instructions
- Clean with a vacuum cleaner.
- Wipe with a fabric dampened with water.
- Storage: Fabric should be stored in a completely dry, clean, and tidy place to prevent mold.
Electrical Parts Information
If the product has electrical parts:
- Usage: This appliance can be used by children aged 8 and above, and persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, provided they have received supervision or instruction on safe use and understand the associated hazards.
- Children's Play: Children shall not play with the appliance.
- Cleaning/Maintenance: User cleaning and maintenance shall not be performed by children without supervision.
- Power Supply: The appliance must only be used with the provided power supply unit.
- Cable Replacement: The external flexible cable or cord of the transformer cannot be replaced; if the cord is damaged, the transformer must be scrapped.
- Heated Surface: Persons insensitive to heat must be careful when using the appliance if it has a heated surface.
- Plug Damage: The power supply unit must not be used if the plug pins are damaged.
Parts List
| Part Identifier | Description | Quantity |
|---|---|---|
| A | Casters | 5 |
| B | Chair Base | 1 |
| C | Gas Lift Cylinder | 1 |
| D | Seat Mechanism | 1 |
| H | Armrest (Note: Diagrams show two armrests are attached, but part list indicates x1) | 1 |
| I | Seat | 1 |
Hardware List
| Part Identifier | Description | Quantity |
|---|---|---|
| E | Screws M6*16 | 4 |
| F | Screws M6*20 | 4 |
| G | Allen Key | 1 |
| (Labeled as 'I' in diagram) | Washers | 8 |
Assembly Instructions
Step 01: Attach the casters (A) to the chair base (B). Insert the gas lift cylinder (C) into the center of the chair base (B). [Diagram shows casters being pushed into the base legs, and the gas lift being inserted into the center hole of the base.]
Step 02: Attach the seat mechanism (D) to the underside of the seat (I). Use armrests (H) and hardware (F, G). [Diagram shows the seat mechanism being aligned with the seat, and armrests being attached to the mechanism using screws F and the Allen key G. Note: The diagram also shows components labeled J and P which are not listed in the parts list.]
Step 03: Place the assembled seat unit onto the gas lift cylinder (C). [Diagram shows the seat assembly being lowered onto the gas lift cylinder.]
Contact Information
If you have any questions, please contact our customer care center. Our contact details are below:
US: ? 001-877-644-9366, customerservice@aosom.com. Imported by Aosom LLC, 27150 SW Kinsman Rd Wilsonville, OR 97070 USA. MADE IN CHINA.
CA: ? 416-792-6088, customerservice@aosom.ca. Imported by Aosom Canada Inc., 7270 Woodbine Avenue, Unit 307, Markham, Ontario Canada L3R 4B9. MADE IN CHINA.
FR: ? 416-792-6088, customerservice@aosom.ca. Importé par Aosom Canada Inc., 7270 Woodbine Avenue, unité 307, Markham, Ontario Canada L3R 4B9. FABRIQUÉ EN CHINE.
IT: ? 0039-0249471447, clienti@aosom.it. IMPORTATO DA/Produttore/REP: AOSOM Italy srl, Centro Direzionale Milanofiori, Strada 1 Palazzo F1, 20057 Assago (MI). FATTO IN CINA.
ES: ? 0034-931294512, atencioncliente@aosom.es. IMPORTADOR/Fabricante/REP: SPANISH AOSOM, S.L., C/ROC GROS,N°15.08550, ELS HOSTALETS DE BALENYÀ, SPAIN. HECHO EN CHINA.
UK: ? 0044-800-240-4004, enquiries@mhstar.co.uk. IMPORTER ADDRESS: MH STAR UK LTD, Unit 27, Perivale Park, Horsenden lane South, Perivale, UB6 7RH. MADE IN CHINA.
DE: ? +49 4087408465, service@aosom.de. ADRESSE DES IMPORTEURE/Hersteller/REP: MH Handel GmbH, Wendenstraße 309, D-20537 Hamburg, Germany. IN CHINA HERGESTELLT.
FR (Additional): ? 0033-1-84166106, aosom@mhfrance.fr. Importé par/Fabricant/REP: MH FRANCE, 2 Rue Maurice Hartmann, 92130 Issy Les Moulineaux, France. FABRIQUÉ EN CHINE.
Recycling information: ♻️ DONNEZ OU RECYCLEZ. Adresses sur quefairedemesdechets.fr.
