VEVOR

Product Image

A front-side view of the VEVOR DZ600-2S-V1 Vacuum Packing Machine, showing its stainless steel construction, transparent lid, and control panel.

Need Help? Contact Us!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate

www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.

Safety Information

⚠️ WARNING

1. Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating.

2. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

GENERAL SAFETY RULES

• Please read the entire operating instructions before using the products for the first time; they contain important information about the correct operation.
• The guarantee/warranty will be void if damage is incurred resulting from non-compliance with the operating instructions. Liability for any and all consequential damage is excluded!
• We do not assume any liability for damage to property or personal injury caused by improper use or the failure to observe the safety instructions! In such cases the guarantee/warranty will be void.
• The unauthorized conversion, modification, or disassembly of the products is inadmissible because of safety and approval reasons (CE).
• The product is not a toy and must be kept out of the reach of children. Particular care must therefore be exercised if children are present.
• The product must not get damp or wet; it is only intended for use in dry, indoor locations (not bathrooms or similarly damp areas). There is a risk of a fatal electric shock.
• Do not expose the product or its accessories to damp or extremely high or low temperatures.
• Do not leave packing materials unattended. They may become dangerous playing material for children.
• Dropping, falling, pressure, or tensile forces could destroy or at least limit the function of the product.
• Never position the device in the vicinity of combustible or easily inflammable materials.
• Always make sure that the rotary table on which the object is placed is located in the center of the housing!
• If you have reason to assume that safe operation is no longer possible, disconnect the device immediately and secure it against inadvertent operation.
• It can be assumed that safe operation is no longer possible if:
  • the device shows visible signs of damage,
  • the device no longer functions,
  • after a longer period of storage under unfavourable conditions,
  • following heavy stress during transportation.

SAVE THESE INSTRUCTIONS

Product Applications

This machine uses plastic film or plastic aluminum film as materials to vacuum package paste foods, fruits, sauce vegetables, chemicals, pharmaceuticals, electronic components, precision instruments, rare metals, and other items. Products packaged under vacuum are not easily oxidized or moldy. Especially suitable for industries such as tea, food, and medicine.

MODEL AND PARAMETERS

STRUCTURE DIAGRAM

Diagrams illustrating the VEVOR DZ600-2S-V1 Vacuum Packing Machine from different angles, showing its external and internal components.

PARTS LIST

OPERATING INSTRUCTIONS

Step 1: Push the door latch towards the center by hand and remove the side door.

Image showing a hand pushing the door latch towards the center to remove the side door of the vacuum packing machine.

Step 2: Unscrew the oil mist filter of the vacuum pump and fill it with oil. The oil level should not be lower than half of the oil window. The oil level should not exceed 3/4 of the visible oil window. It is strictly prohibited to start the vacuum pump without oil. (Note: two vacuum pumps)

Image showing a hand unscrewing the oil mist filter of a vacuum pump and filling it with oil from a bottle.

3. PANEL OPERATION INSTRUCTIONS

• [1] Time and status display: Displays "_" as standby mode; "00" as deflation status. Numbers indicate vacuum, sealing, permanent temp, or cooling status (with decimal points).
• [2] Emergency stop button: Use when there is a problem with the machine operation or when it is needed to stop urgently.
• [3] VACUUM time setting key: In standby state, press to set vacuum time. Adjusting time range: 0-99 seconds.
• [4] SEALING time setting key: In standby state, press to set sealing time. Adjusting time range: 0-9.9 seconds.
• [5] SEALING TEMPERATURE setting key:
  • a: For setting SEALING TEMPERATURE. Press to cycle through LOW, MIDDLE (Recommended), HIGH indicator lights, or no indicator (no temperature state).
  • b: For setting cooling time. Hold for 5 seconds, then adjust. Adjusting time range: 0-9.9 seconds (Factory setting is 2S).
• [6] INCREASE key: Increases the flickering bit value when setting time.
• [7] DECREASE key: Decreases the flickering bit value when setting time.

4. PANEL USAGE INSTRUCTIONS

1. Step 1: Connect the matching power supply.
2. Step 2: Open AIR SWITCH.
3. Step 3: Press the [3] VACUUM button for vacuum time. Use [6] INCREASE or [7] DECREASE keys to adjust time as required, generally about 25 seconds.
4. Step 4: Press the [4] SEALING button for sealing time. Use [6] INCREASE or [7] DECREASE keys to adjust time, generally about 2 seconds for normal bags. It is strictly prohibited to set the sealing time too long or burn out the sealing heating strip.
5. Step 5: Press the [5] SEALING TEMPERATURE button twice, select the MIDDLE indicator light. Medium temperature state is recommended for general items.

Note: Pressing [3] VACUUM and [7] DECREASE together refers to the PERMANENT TEMP setting, which is factory set and requires no change.

Step 5: Place the product to be packaged into a vacuum chamber. Pick up the bag pressing rod and place the vacuum bag flat on the sealing strip. Put down the bag pressing rod.

Image showing a vacuum bag containing items placed flat on the sealing strip inside the vacuum chamber, with the bag pressing rod lowered.

Step 6: Press the front end of the vacuum cover by hand during operation. When operating, press the edge of the vacuum cover by hand, and the vacuum machine starts to work. After the vacuum machine starts to run, the hand leaves the machine. The [11] VACUUM metre pointer will indicate 0.06-0.08 to achieve the vacuum purpose, and the machine will automatically complete the packaging process.

Image showing a hand pressing down on the edge of the vacuum cover to initiate the vacuum packing process.

Step 7: When the machine needs to change oil or is not used for a long time, loosen the screw under the oil window and drain the vacuum pump oil. Suggest replacing the vacuum pump oil after the machine has been working continuously for 800 hours.

Image showing a hand loosening a screw beneath the oil window of a vacuum pump to drain the oil.

CIRCUIT DIAGRAM

A schematic diagram illustrating the electrical connections and components of the vacuum packing machine.

MAINTENANCE

• After use, the surface of the machine should be cleaned and residual materials inside the machine should be removed.
• When storing, keep in a clean, dry, and safe location away from children.
• All maintenance, service, and repairs not discussed in the manual should only be performed by qualified service technicians.

Replace the high temperature cloth (Teflon Cloth)

Procedure:

• 1. Remove the screws on both sides of the tray, and then pick up the whole tray.
• 2. Remove the upper screws.
• 3. Remove the old high-temperature cloth.
• 4. Apply new high temperature cloth.
• 5. Reinstall the original screws.
• 6. Completing the Installation.

Images illustrating the steps for replacing the high-temperature cloth: removing tray screws, removing upper screws, removing old cloth, applying new cloth, reinstalling screws, and completing the installation.

Replace the Chamber Sealing Strip

Procedure:

• 1. Remove the Chamber Sealing Strip.
• 2. Inject new glass glue into the track to ensure air tightness.
• 3. Replace the Chamber Sealing Strip with a new one.
• 4. Completing the Installation.

Images illustrating the steps for replacing the chamber sealing strip: removing the old strip, applying sealant glue, installing the new strip, and completing the installation.

TROUBLESHOOTING AND SOLUTIONS

CORRECT DISPOSAL

European Directive 2012/19/EC Compliance

This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through ?️ indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

Manufacturer and Representatives

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi, Shanghai

EC REP: SHUNSHUN GmbH.

Address: Römeräcker 9 Z2021, 76351 Linkenheim-Hochstetten, Germany

Tel: +49 1727041930

Email: euvertreter@gmail.com

UK REP: Pooledas Group Ltd.

Address: Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom

Tel: 01772418127

Email: pooledas123@gmail.com

Imported to AUS: SIHAO PTY LTD.

Address: 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd.

Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Made In: China