DAEMA

CONTENTS

• 1. GENERAL SAFETY PRECAUTIONS (Pages 1-2)
• 2. PART IDENTIFICATION (Pages 3-5)
• 3. SPECIFICATIONS (Page 6)
• 4. INSTALLATION AND ADJUSTMENT (Page 7)
• 5. DRAIN PIPE USAGE (Page 8)
• 6. INSTALLATION OF THE WATER INLET (Pages 9-10)
• 7. OPERATION INSTRUCTION (Page 11)
• 8. FEATURES DESCRIPTION (Page 12)
• 9. TROUBLE SHOOTING (Page 13)
• 10. CARE AND CLEANING (Page 14)

GENERAL SAFETY PRECAUTIONS

⚠️ Warning

This mark means “danger”. The content is related to safety of user and washing machine. Please operate according to the instructions or it may lead to damage.

? Prohibited

This mark means no permission, or it will lead to washing machine damage.

Ensure the earth connection in your electrical supply is proper before connecting the power cord. The socket should be standard and independent of 3 pin BS plug of 220V AC, 50Hz. A connection with separate line fuse or circuit breaker of the value pf 6A/16A.

Pull out plug and turn off water tap when there is no power supply.

Diagram Description: Illustration showing an electrical plug being pulled out of a socket and a water tap being turned off.

Do not bend/twist the electrical cord too much. Please contact our after sales service department when line or socket is damaged or slacked.

⚠️ Caution

⚠️ Caution

Do not install the machine in damp surrounding such as bathroom. Never rinse or wash the machine; Never put the wet clothes on control panel.

Do not use hot water more than 65°C.

Diagram Description: Illustration showing a washing machine in a bathroom with a prohibition symbol over rinsing the machine. Another illustration shows wet clothes placed on the control panel with a prohibition symbol. A thermometer icon shows 65°C with a prohibition symbol.

Do not block up vent when you install the washer on carpet floor.

Do not wash raincoats, bicycle covers, etc.; to prevent severe vibration.

Diagram Description: Illustration showing a washing machine with a vent blocked by a soft object, with a prohibition symbol. Another illustration shows a washing machine with raincoats and bicycle covers being washed, with a prohibition symbol. Text indicates "Soft Object" and "Vent".

Do not use extension junction box since it may not be properly earthed; Do not use an extension cord.

Diagram Description: Illustration showing an extension junction box connected to the washing machine with a prohibition symbol. Another illustration shows an extension cord with a prohibition symbol.

Never open the wash lid or put your hand in washer tub when washing or spinning process is going on.

Do not dismantle or repair the washer by yourself.

Diagram Description: Illustration showing a hand reaching into a washing machine during operation with a prohibition symbol. Another illustration shows a person trying to repair a washing machine with a prohibition symbol.

Do not put any hot or heavy objects on the washer!

Do not wash clothes with volatile material such as alkaline or petrol.

Diagram Description: Illustration showing heavy objects placed on top of the washing machine with a prohibition symbol. Another illustration shows clothes with symbols for alkaline and petrol (汽油) with a prohibition symbol.

Do not permit children to go near the machine.

Do not expose the machine to direct sunlight, rain or heat.

Diagram Description: Illustration showing children near the washing machine with a prohibition symbol. Another illustration shows the washing machine exposed to sun, rain, and heat with a prohibition symbol.

Maintenance Steps:

• Please clean the magic filter after every 5 wash cycles.
• Ensure that the plug is disconnected to wall socket before taking out the filter.
• Drain off all water in the tub.
• Pull the filter out and wash it as shown in the picture.
• Assemble the filter again after cleaning it.

General Advice:

• Please ensure that you empty all pockets of objects such as coins, pens, toothpics, match sticks etc. They might get stuck inside the machine and could cause damage to your clothes.
• Please ensure the tap is open and water inlet is connected properly when washing.
• Detergent powder with little soap is recommended.
• Please check recommended wash powder quantity list for reference.

Diagram Description: Illustrations show steps for cleaning a filter, emptying pockets, connecting a water tap, and using detergent.

PART IDENTIFICATION

Washing Machine Components

Diagram Description: An illustration of the washing machine with its lid open, showing internal components. Labels point to: Fixed socket, Inlet hose, Lid, Detergent box, Inner tub, Lint filter, Pulsator, Control panel, Power cord, Box, Drain hose, Liquid detergent entrance, Adjustable foot.

Accessories

Diagram Description: Illustrations of the Inlet hose, Noise & Rat-Proof Plate, Instruction manual, and Spring clamp Drain pipe.

Control Panel Display DWF-9001Q

Diagram Description: An illustration of the control panel with buttons and a digital display. The display shows "88" and various indicator lights. Buttons are labeled and numbered: 1. POWER, 2. WATER LEVEL, 3. PROCESS, 4. PROGRAM, 5. START/PAUSE.

Button Functions:

1. Power button: Press to turn on/off the washing machine. Do not turn on again until 3 minutes after it is turned off. The machine turns off automatically when the program finishes or if the start button is not pressed within 10 minutes of powering on.
2. Water level button: Press to select the water level.
3. Process button: Press to select the desired process.
4. Program button: Press to select the desired program.
5. Start/pause button: Press to start/pause the washing machine.

Control Panel Display DWF-1801Q & DWF-1401Q & DWF-2001Q

Diagram Description: An illustration of the control panel, similar to the DWF-9001Q but with slightly different program options and labels. Buttons are labeled and numbered: 1. POWER, 2. WATER LEVEL/AIR DRY, 3. PROCESS, 4. DELAY START (PRESET), 5. PROGRAM, 6. START/PAUSE.

Button Functions:

1. Power button: Press to turn on/off the washing machine. Do not turn on again until 3 minutes after it is turned off. The machine turns off automatically when the program finishes or if the start button is not pressed within 10 minutes of powering on.
2. Water level button/Air dry: Press to select water level or air dry function.
3. Process button: Press to select the desired process.
4. Delay start (preset) button: Hold the water level button, then press water supply to set up the reservation time of delay start.
5. Program button: Press to select the desired program.
6. Start/pause button: Press to start/pause the washing machine.

SPECIFICATIONS

Dimensions:

DWF-9001Q: 575mm (Width) x 575mm (Depth) x 965mm (Height)

DWF-1401Q: 605mm (Width) x 640mm (Depth) x 995mm (Height)

DWF-1801Q: 685mm (Width) x 700mm (Depth) x 1070mm (Height)

DWF-2001Q: 685mm (Width) x 700mm (Depth) x 1100mm (Height)

Diagram Description: Illustrations showing the side and front views of each washing machine model with their dimensions indicated.

INSTALLATION AND ADJUSTMENT

Placement Guidelines:

• Do not place the washing machine on a slanting, uneven or unstable surface.
• Place the washing machine on a solid levelled surface to avoid excessive vibration during operation.

Diagram Description: Illustrations show incorrect placement on sloped/uneven surfaces (with prohibition symbols) and correct placement on a level surface.

Installation Notes:

• Keep the machine at least 10cm away from the wall on all sides.
• Place the drain hose flat on the floor before operating the machine.
• Washing machine should be directly connected to a socket.
• Switch off the machine when not in operation.

Diagram Description: Illustrations show spacing around the machine, drain hose placement, direct electrical connection, and switching off the machine.

Important Notes:

• If the power cord is damaged, it must be replaced by an authorized service person to avoid hazard.
• Discard the cushion balance ring assembly cover.
• Remove transit bracket.

Dismantling the package:

• Dismantle the package and take out the rat mesh package with upper foam.
• Open the wash lid and take out all the accessories.
• Remove all packaged items including convex plastic cube.

Adjusting The Washing Machine:

• The front legs of the machine are adjustable. Lift the front side slightly and rotate the legs to let the machine stable and horizontal.
• Then lock the nut if the legs have a nut.
• Please check whether the machine is horizontal as shown in the picture.

Diagram Description: Illustrations show how to adjust the machine's feet for leveling.

DRAIN PIPE USAGE

Change the direction of the drain hose:

Diagram Description: Three illustrations show how to unfasten a screw, lead the drain hose to the other side, and fasten the screw to fix the drain hose.

Extension of the drain hose (down drain):

Diagram Description: A diagram illustrates the correct and incorrect placement of the drain hose for height and length.

INSTALLATION OF THE WATER INLET

Proper water inlet:

Diagram Description: Three illustrations show suitable tap shapes (circular) and unsuitable shapes (elliptical, hexagonal) for the water inlet adapter. Text states "Use the adaptor only on circular cross section of the taps." and "The tap mouth should be smooth. Front length should be more than 10mm."

Connect the adaptor to the tap:

1. Detach the adaptor from the water inlet pipe accessories. Hold the bottom part of locking lever and press down the slider.
2. Loosen the four screws of the tap adaptor and press the tap adaptor against the mouth of the water tap. Detach the ring if it is smaller than the tap mouth.
3. Tighten the screws evenly.
4. Remove the mark, rotate the nut in counter clockwise direction.

Diagram Description: Illustrations numbered 1-6 show the steps for attaching the adapter to the tap, including detaching the adapter, loosening screws, fitting the adapter, tightening screws, removing a mark, and rotating a nut.

Connect the inlet water pipe to the machine:

1. Do not detach the water proof ring. Check if the ring is damaged before washing.
2. Cover the pipe nut on the water valve.
3. Fit the nut tightly.

Diagram Description: Illustrations show connecting the pipe nut to the water valve with a ring.

Connect the inlet water pipe to the adaptor:

1. Press down the slider, insert the pipe into the adaptor.
2. Let the locking lever hook the pipe connector, release the slider until you hear a sound.

Diagram Description: Illustrations show inserting the pipe into the adaptor and securing it with the locking lever.

Check the water inlet pipe and the tap:

1. Pull the pipe gently to check whether it is tight.
2. Open the tap to check leakage.
3. Ensure the pipe is connected to the tap and the machine properly before each wash.

Diagram Description: Illustrations show checking the pipe connection for tightness and potential leaks, with prohibition symbols for incorrect connections.

Detach the inlet water pipe:

1. Close the water tap.
2. Hold the locking lever and press down the slider, then take down the pipe.

Diagram Description: Illustrations show how to detach the water pipe by closing the tap, holding the lever, and pressing the slider.

OPERATION INSTRUCTION

Steps:

1. Press the "POWER" button to turn on the machine.
2. Press the "PROGRAM" button to choose the program you want. (Note: To change a settled program, press "POWER" or "START/PAUSE" to stop, then press "PROGRAM".)
3. Press the "WATER LEVEL" button to choose the water level you want, and put detergent accordingly. (Note: Water level can be changed during working. If changed to higher, machine stops to fill water and starts when settled level is reached.)
4. Close the wash lid.
5. Press the "START/PAUSE" to start operating.

Diagram Description: Illustrations show the POWER, PROGRAM, WATER LEVEL, and START/PAUSE buttons.

Notes:

• Please make sure the highest point of clothes is below the balance ring.
• For air function, press "PROGRAM" to choose air dry, then press "WATER LEVEL" to choose time.
• FUZZY LOGIC is an intelligent program. Press PROGRAM to choose NORMAL function, and the machine will choose the best procedure according to the wash capacity.

FEATURES DESCRIPTION

Auto Alarm

Other Features:

• 1. Fuzzy Logic: The machine selects the program/process/water level/rinse cycle, etc., by itself by detecting the size, dirt, and weight of clothes.
• 2. Memory Backup: The machine remembers wash cycle status if power cuts off during the washing process. It will continue the process once the power is back.
• 3. LED Display: Intelligent central digital dynamic LED display indicates the operation status vividly.
• 4. Delay Start: Select delay start time from 1 Hr to 24 Hr separately; the machine will start working with the set program after the desired time.
• 5. Crystal Drum: Special design improves wash quality and reduces wear rate of clothes.
• 6. Tub Clean: Recommended every 2 weeks. Press Program button to select Tub Clean, close lid, press Start/Pause.
• 7. Air Dry: Air is supplied to clothes during wash/rinse to keep them fresh.
• 8. DIY (Do It Yourself): Automize and save a program as per your needs.
• 9. IMD: "In-mould decoration" technology keeps the panel shining.
• 10. Damping Lid: The lid closes smoothly to avoid jerks.
• 11. Child Lock: Activated by pressing Water Level and Reset buttons together during running.
• 12. Bubble Wash: Generates soap bubbles that collide with clothes for better soaking.
• 13. Anti Creases: Machine does not drain in the last cycle to prevent creases; water can be reused.

TROUBLE SHOOTING

Key points for trouble locating:

Washing machine not running

• Is the water tap open?
• Is the power cord plugged into the socket properly?
• Is the power supply turned on?
• Is the Fuse sound?
• Is the water Level enough?

Diagram Description: Illustration of a washing machine with a question mark and a power plug icon.

No water entering the machine

• Is the water tap open?
• Has the water supply ceased?
• Is the water inlet hose of connection pipe clogged?
• Has the water tap frozen?
• If water supply is not supplied within 50 minutes, the buzzer will give out an audible alarm.

Diagram Description: Illustration of a washing machine with water taps and hoses, showing a question mark.

Water is not draining out of the machine

• Is the drain pipe let down?
• Is the drain pipe frozen?
• Is the drain pipe clogged?
• If the drain is not realized within 20 minutes, the buzzer will give out an audible alarm.

Diagram Description: Illustration of a washing machine with a drain hose, showing a question mark.

The Rinse/Spin cycle is not functioning properly.

• Are the clothes put evenly inside the washing barrel?
• Is the washing machine positioned stable and horizontally?
• Is the top cover of the washing machine close?

Diagram Description: Illustration of a washing machine with clothes inside, showing a question mark.

Power supply cannot be turned off

• If the error flag is still displayed, contact commercial agent of service center.

Diagram Description: Illustration showing a power cord and a question mark.

Water is overflowing from the machine

• Drain the machine.
• If the error flag is still being displayed, contact an authorised service center.

Diagram Description: Illustration of a washing machine with overflowing water and a question mark.

CARE AND CLEANING

Program Finish:

The machine will make a buzzer sound automatically once the program finishes.

Shell Maintenance:

Wipe the machine with soft and dry cloth after each wash. Do not use soda or bleach for cleaning the washing machine.

Diagram Description: Illustration of wiping the washing machine with a cloth.

Magic Filter Clearance:

• Ensure the Magic Filter is assembled before washing.
• Clean the Magic Filter after each wash as shown in the picture.

Diagram Description: Illustrations show how to clean the magic filter.

Inlet Mouse Clearance:

Please clean the inlet filter if it is blocked.

Clean the lint filter:

1. Please pull out the lint filter according to the direction of arrow.
2. Firstly, open the lint filter and then close it after cleaning and rinsing thoroughly.
3. Reinstall the lint filter according to the direction of arrow.

Diagram Description: Illustrations show the steps for removing, cleaning, and reinstalling the lint filter.

Disposal Information:

Symbol Description: A symbol showing a crossed-out wheeled bin indicates that this product should not be disposed of with household waste. It should be recycled responsibly to promote sustainable reuse of material resources. Contact the retailer or use return/collection systems for environmental safe recycling.

Distributed by:

Daewoo Electronics
Sales & Services (M) Sdn. Bhd
Lot 886, Bay B2-B4, Jalan Subang 9,
Taman Perindustrian Subang,
Off Jalan Puchong Hicom,
47500 Subang Jaya, Selangor.