Coospo BC107 User Manual

Status Icons

• Distance: DST
• Ascend Distance: AST
• Calories: CAL
• Cadence: CAD
• Heart Rate: HRM
• LAP: LAP
• Maximum: Maximum
• Sport time: Sport time
• Altitude: ALT
• Odometer (Total distance): ODO
• Gradient: GRA
• Time: TIME
• No satellite signal: ??️
• Satellite signal level: ?️
• Accessory connecting status: ?
• Manual pause: ⏸️
• Connected with App by BLE: ??
• Temperature: ?️
• Battery level: ?
• Under exercising: ▶️
• Increased & Decreased: ??
• Power: PWR
• Average: Average
• Miles per hour: MPH
• KMH Kilometers per hour: KMH

Standard Accessories

• Main Device x 1
• Big size rubber ring x 2
• Small size rubber ring x 2
• User Manual x 1
• Standard bike mount x 1
• Rubber pad for standard bike mount x 1
• Charging Cable x 1

How to Install

Standard Mount Installation

1. Install the rubber pad onto the mount.
2. Tie the mount onto the bar with the rubber rings.
3. Tie up the mount.
4. Install the main device onto the mount.
5. Rotate the main device for 90 degrees.
6. Installation completed.

Charging

Open the rubber cover, connect the device with USB cable to charge.

Use USB DC 5V power adaptor / Computer.

During the charging, the battery icon will flash until fully charged.

Please charge the device before first time use.

Acquiring Satellite Signals, Time Setting and Auto Backlight

Acquiring Satellite Signals

Please make sure the device is outdoor and under a clear view of sky. Usually it may take 15~90 seconds to locate satellite signals. Remain stationary when acquiring satellite signals.

This device can use a speed sensor or GPS for speed tracking. When the speed sensor is not connected, the device will use GPS for speed tracking, and will use the speed sensor when the sensor is connected.

Time Setting

The time and date will be calibrated automatically after locating satellite signals when the device is powered on (Please set the time zone correctly, refer to the time zone setting chapter) or connect the device to the App (CoospoRide) to sync the time.

Auto Backlight

This device will automatically calculate the sunrise and sunset times. From half an hour before sunset to half an hour after sunrise, the backlight will be automatically illuminated. In the rest of the time, the backlight will be turned off if no operation is detected in 15 seconds.

Setting the Wheel Size

Hold the [Mode] button to get into setting mode.

1. There are 5 settings pages available (P1 ~ P5), press the [Up/Down] button to switch to P2.
2. Press the [Enter] button to select.
3. Press the [Up/Down] button to select the setting digit, press the [Enter] button to set the numbers.
4. Press the [Enter] button to save and exit (Automatically exit in 6 seconds if no operation detected).

Note: The selected digit will flash during setting.

Common wheel size and circumference are listed in the manual.

Time Zone Setting

Hold the [Mode] button to get into setting mode.

1. There are 5 settings pages available (P1 ~ P5), press the [Up/Down] button to switch to P3.
2. Press the [Enter] button to select (Default time zone: UTC/GMT + 08:00).
3. Press the [Up/Down] button to select the setting digit, press the [Enter] button to set the numbers.
4. Press the [Enter] button to save and exit (Automatically exit in 6 seconds if no operation detected).

Note: The selected digit will flash during setting.

Connecting with ANT+ Sensors

1. Please make sure the sensors are in wake-up mode (For example, the heart rate monitor should be worn correctly, and the speed/cadence and power meter should be awakened by turning the pedals or wheels).
2. Hold the [Mode] button to get into setting mode.
3. There are 5 settings pages available (P1 ~ P5), press the [Up/Down] button to switch to P1.
4. Press the [Enter] button to select to enter.
5. The computer automatically searches for ANT+ peripherals and connects after searching.
6. Press the [Enter] button to save the found accessories and return. If no ANT+ accessory is found, the device will return to the previous page automatically.

Note: When a power device is connected during riding, the computer will display power data first. If there is no power device, it will display GRA slope data.

Power Calibration

1. Hold the [Mode] button to get into setting mode.
2. There are 5 settings pages available (P1 ~ P5), press the [Up/Down] button to switch to P5; it will automatically calibrate.
3. Short press the [Enter] button to recalibrate. The value flashes during calibration; the value does not flash after calibration is successful.
4. After successful calibration, press the [Enter] button to save and exit (Automatically exit in 20 seconds if no operation detected).

Button Function

• Left Button: Short Press: Mark a new lap. Hold for 2 seconds: Power off. (Power on: short press the button). (Short press in setting mode: exit / return and save the setting).
• Mid Button: Short Press: Pause / Continue (Short press to start recording after power on). Hold for 2 seconds: Save the exercise record and exit the exercise. (Short press in setting mode: enter the current setting / switch the number of digits).
• Right Button: Short Press: Page turning. Hold for 2 seconds: Setting mode. (Short press in setting mode: switch setting options / switch the numerical).

Cycling

Bluetooth Connection

Compatible with: Any Bluetooth 4.0 enabled Android device with Android 4.3 and above, iOS 9.0 version and above, iPhone 4s and above.

Download CoospoRide in Google Play or App Store.

Binding:

1. Power on the bike computer.
2. Open the CoospoRide App, enter the binding computer step, select the BC107 computer in the device list to bind the device (the phone needs to turn on Bluetooth and allow Bluetooth permissions).

Data Synchronization

In the activity page of the App, click on the connected device to enter the record synchronization operation page. Through authorization to Strava in the App's more settings, the computer data can be synchronized to the Strava platform at the same time.

Select the record to be synchronized and click Sync. The record on the computer will be deleted automatically after synchronization.

Basic Parameters

• Display: FSTN Screen, 2.3 inch
• GPS & BDS: Yes
• Wireless ANT+ & Bluetooth: Supported
• File Transfer: Bluetooth (Specified App Compatible) .fit
• Accessories Supported: ANT+ peripherals (Heart Rate Monitor, Speed Sensor, Cadence Sensor, Speed and Cadence 2 in 1 Sensor, Power Meter)
• Battery Capacity: 1000mAh
• Battery Life: 28 hours for a single use after fully charged
• Material: PC+ABS+TPU
• Dimension: 81x54x20.6 mm
• Weight: 64g
• Water Resistance: IPX7
• Language: English
• Lap Count: 1000
• Locate mode: GPS searching is Auto after power on. Please start cycling after the GPS positioning is successful.
• Backlight: Yes

GPS Positioning

No signal: ??️

Weak: ?️

Normal: ?️?️

Strong: ?️?️?️

No Speed data display:

1. If you start riding when the GPS is not positioned successfully (speed sensor not connected), the speed data (real-time, average, maximum) will be displayed as '--', and the rest of the data remains the same.
2. Tips: You can stand still for 3-5 minutes to get more connections with satellites for better GPS signal.
3. Note: Please make sure you are outdoor when positioning. Bad weather and dense forest may affect GPS signal.

Attentions

The water-resistant level of the bicycle computer is IPX7. It can be used in the rain if you close the protective cover on the back tightly. It is recommended to take down the bicycle computer and put it into a waterproof bag if it rains heavily.

Responsibility Disclaimer

The information contained in this manual is just for reference. The product described above may be subject to alteration owing to the manufacturer's continuing research and development plans, without making an announcement in advance.

Coospo shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or in connection with this manual or the contained product.