Teltonika FMC234: Waterproof GPRS/GNSS Tracker Quick Manual

Content

• Know your device
• Pinout
• Wiring scheme
• Set up your device
• PC Connection (Windows)
• How to install USB drivers (Windows)
• Configuration
• Quick SMS configuration
• Mounting recommendations with a standard cable
• Basic characteristics
• LED indications
• Electrical characteristics
• Safety information
• Certification and Approvals
• Warranty
• Warranty disclaimer

Know Your Device

The FMC234 is a waterproof GPRS/GNSS tracker with a high-capacity battery. It features a 2x6 socket, GNSS antenna, Micro SIM slot, and battery socket. It also has a status LED and a navigate LED.

Top View: Shows the 2x6 socket.

Bottom View (without cover): Shows the GNSS antenna.

Top View (without cover): Shows the Micro SIM slot, battery socket, status LED, and navigate LED.

Pinout

FMC234 2x6 socket pinout

Wiring Scheme

The wiring scheme illustrates the connections for various functions including ignition detection, alarm button, fuel gauge, analog sensor, door sensor, buzzer, LED lights, power supply, and central lock. It also shows connections to ALL-CAN300, LV-CAN200, CAN-CONTROL, temperature sensors, and iButton.

Set Up Your Device

How to insert Micro-SIM card and connect the battery:

1. Partly Closed Device: You will receive your device partly closed.
2. Cover Removal: Gently remove top and bottom covers.
3. SIM Card Insert: Insert SIM card with PIN request disabled. Ensure the SIM card cut-off corner points outward from the slot. SIM slot 1 is closer to the PCB, SIM slot 2 is the top one. Refer to the Teltonika Wiki for detailed instructions.
4. Battery Connection: Connect the battery as shown, ensuring it does not obstruct other components.
5. Attaching Cover Back: After configuration, attach the device top and bottom covers back and press them to fully close.
6. Completely Closed Device: Ensure the product casing is closed correctly.

Important: The device has an IP67 casing with a two-phase closing for reliable protection. Ensure corner clips are tight and the cable is connected correctly.

PC Connection (Windows)

1. Power up the FMC234 with a 10-30 V DC power supply. Observe LED indications.
2. Connect the device to your computer via Micro-USB cable or Bluetooth®.
• Micro-USB Cable: Install USB drivers as described in the "How to install USB drivers (Windows)" section.
• Bluetooth® Wireless Technology: Enable Bluetooth® on your PC, select "Add Bluetooth or other device > Bluetooth", choose your device (e.g., "FMC234_last_7_imei_digits"), enter the default password "5555", connect, and select "Done".
3. The device is now ready to be used on your computer.

Refer to the Teltonika Wiki for LED status information.

How to Install USB Drivers (Windows)

1. Download COM port drivers from the provided link.
2. Extract and run `TeltonikaCOMDriver.exe`.
3. Follow the on-screen prompts, clicking "Next" and "Install".
4. Click "Finish" to complete the driver installation.

Driver download link: teltonika.lt/downloads/en/FMC234/TeltonikaCOMDriver.zip

Configuration

The FMC234 device comes with default factory settings. To change these settings, use the Teltonika Configurator software. The Configurator operates on Microsoft Windows OS and requires the MS .NET Framework. Ensure you have the correct version installed.

MS .NET Requirements

The Configurator software allows you to manage various settings, including GPRS, server settings, and data acquisition parameters. Detailed information can be found on the Teltonika Wiki.

Configurator Functionality:

• Load from device: Loads configuration from the device.
• Save to device: Saves configuration to the device.
• Load from file: Loads configuration from a file.
• Save to file: Saves configuration to a file.
• Update firmware: Updates the device firmware.
• Read records: Reads records from the device.
• Reboot device: Restarts the device.
• Reset configuration: Sets the device configuration to default.

The Status window provides information on GNSS, GSM, I/O, and Maintenance. User-editable profiles can be loaded and saved.

Quick SMS Configuration

You can quickly set up your device by sending an SMS command with the following format:

`setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0`

Note: Insert two space symbols before the SMS text.

GPRS SETTINGS:

• 2001 – APN
• 2002 – APN username (leave empty if not applicable)
• 2003 – APN password (leave empty if not applicable)

SERVER SETTINGS:

• 2004 - Domain
• 2005 - Port
• 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Example SMS: `setparam 2001:internet;2002:internet1;2003:internet2;2004:avl2.teltonika.lt;2005:12050;2006:0`

Default Configuration Settings

Movement and Ignition Detection:

• Vehicle Movement: Detected by accelerometer.
• Ignition: Detected by vehicle power voltage (13.2 - 30 V).

Device Makes a Record on Moving if One of These Events Happen:

• Vehicle Drives: 100 meters.
• Passes: 300 seconds.
• Vehicle Turns: 10 degrees.
• Speed Difference: Greater than 10 km/h between last coordinate and current position.

Device Makes a Record on Stop if:

• 1 Hour Passes: Vehicle is stationary and ignition is off.

Records Sending to Server:

• Every 120 Second: Sent to the server if a record has been made.

After SMS configuration, the device synchronizes time and updates records. Time intervals and I/O elements can be adjusted via Teltonika Configurator or SMS parameters.

Mounting Recommendations with a Standard Cable

Connecting Wires

• Fasten wires to non-moving parts, avoiding heat sources.
• Ensure connections are not easily visible. Reapply factory isolation if removed.
• Apply additional isolation for wires exposed to exterior elements (heat, humidity, dirt).
• Do not connect wires to board computers or control units.

Connecting Power Source

• Verify power availability after the car computer enters sleep mode (typically 5-30 minutes).
• Measure voltage after connecting the module to ensure no decrease.
• Connect to the main power cable in the fuse box.
• Use a 3A, 125V external fuse.

Connecting Ignition Wire

• Ensure it's a real ignition wire (power remains after engine start).
• Avoid ACC wires (where electronics are active with the key in the first position).
• Check power availability when other vehicle devices are turned off.
• Connect to the ignition relay output or an alternative relay with ignition-controlled power.

Connecting Ground Wire

• Connect the ground wire to the vehicle frame or metal parts.
• If using a bolt, connect the loop to the end of the wire.
• Scrub paint from the connection point for better contact.

Basic Characteristics

Module

GNSS

Cellular

Power

Bluetooth® Technology

Interface

Physical Specification

Operating Environment

Features

LED Indications

Navigation LED Indications

Status LED Indications

Electrical Characteristics

Supply Voltage

Digital Output (Open Drain Grade)

Digital Input

Analog Input

Negative Input

Output Supply Voltage 1-Wire

Safety Information

This section provides crucial information for operating the FMC234 safely. Failure to follow these recommendations may lead to dangerous situations.

• General Precautions: Do not disassemble the device. If damaged, avoid touching it until the power supply is unplugged. Wireless data transfer may cause interference with nearby devices. Only qualified personnel should connect the device. Ensure the device is firmly fastened. Programming should be done with a PC and autonomic power supply. Installation during lightning storms is prohibited. The device is susceptible to water and humidity.
• Power Source: The device uses a SELV limited power source with a nominal voltage of +12 V DC and an allowed range of +10...+30 V DC.
• Handling and Transport: Transport the device in an impact-proof package to avoid mechanical damage. Ensure LED indicators are visible for status checks.
• Connections: Disconnect vehicle power supply jumpers before connecting the 2x6 connector wires. Disconnect the 2x6 connector before unmounting the device. The device should be mounted in a zone of limited access. All related devices must meet EN 62368-1 standard.
• Usage: The FMC234 is not designed as a navigational device for boats.
• Battery Disposal: Risk of explosion if the battery is replaced with an incorrect type. Dispose of used batteries according to instructions. Do not dispose of batteries with general household waste; take them to a recycling center or designated bin.

Certification and Approvals

• User Manual: Read the User's Manual before use. The full version is available on the Teltonika Wiki.
• CE Marking: Indicates conformity with European Directive 2014/53/EU (RED).
• RoHS: Regulates the manufacture, import, and distribution of Electronics and Electrical Equipment (EEE), banning 10 hazardous materials.
• IP Rating: Provides detailed information on water and dust resistance.
• E25 Marking: European conformity mark for the transport sector, indicating compliance with relevant laws and regulations.
• REACH: Addresses the production and use of chemical substances and their impact on health and the environment.
• Bluetooth®: Word mark and logos are registered trademarks of Bluetooth SIG, Inc., used under license by UAB Teltonika Telematics.

Declaration of IMEI Assignment

The IMEI number identifies devices on a GSM network and can be used to blacklist stolen phones. If a phone is stolen, the owner can instruct their network provider to blacklist it using the IMEI number, rendering it useless on that network.

Check All Certificates

The latest certificates can be found on the Teltonika Wiki.

Warranty

• Teltonika guarantees a 24-month warranty period for its products.
• All batteries carry a 6-month warranty period.
• Post-warranty repair service is not provided.

If a product stops operating within the warranty period, it may be:

• Repaired
• Replaced with a new product
• Replaced with an equivalent repaired product
• Replaced with a different product (in case of End-of-Life for the original product)

An extended warranty period can be arranged separately.

Warranty Disclaimer

• Customers may only return products due to defects from order assembly or manufacturing.
• Products are intended for use by trained and experienced personnel.
• Warranty does not cover defects caused by accidents, misuse, abuse, catastrophes, improper maintenance, inadequate installation, or use with incompatible equipment.
• Warranty does not cover consequential damages.
• Warranty is not applicable to supplementary product equipment (e.g., PSU, power cables, antennas) unless the accessory is defective upon arrival.

For more information on RMA, refer to the Teltonika Wiki.