Sigma Duo Magnetless Speed and Cadence Sensor

Regulatory Information

Industry Canada Statement

This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 cm between the radiator and your body.

Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement doit être installé et utilisé avec une distance minimale de 20 centimètres entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisé ou opérant en conjonction avec autre antenne ou émetteur. Les antennes utilisées pour cet émetteur doivent être installés et fournir une distance de séparation d'au moins 0.5 centimètre de toute personne et doit pas être co-située ni fonctionner en conjonction avec une autre antenne ou émetteur.

CE Statement

You can find the CE declaration at: ce.sigmasport.com/duomagnetlesscadence (EN)

Die CE-Erklärung kann hier eingesehen werden: ce.sigmasport.com/duomagnetlesscadence (DE)

La déclaration CE peut être consultée ici : ce.sigmasport.com/duomagnetlesscadence (FR)

La dichiarazione CE è consultabile qui: ce.sigmasport.com/duomagnetlesscadence (IT)

Encontrarás la declaración de conformidad CE en: ce.sigmasport.com/duomagnetlesscadence (ES)

Je kunt de CE-verklaring hier inzien: ce.sigmasport.com/duomagnetlesscadence (NL)

Deklarację CE znajdziesz tutaj: ce.sigmasport.com/duomagnetlesscadence (PL)

CE prohlášení najdeš pod následujícím odkazem: ce.sigmasport.com/duomagnetlesscadence (CZ)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Product Specifications

• Battery type: CR 2032 x 3 V
• Operation temperature: -20 °C to 60 °C
• Operation frequency: ANT+ 2.4 GHz @ 1 dBm nominal, Bluetooth 2.4 GHz @ 1 dBm nominal
• Transmission power: 0~4 dBm
• Water rating: IPX7

Accessories

DUO MAGNETLESS SPEED
Art.-Nr. 021010

O-RINGS
Art.-Nr. 090022

DUO MAGNETLESS CADENCE
Art.-Nr. 021011

Installation and Operation

Speed Sensor Installation

The SPEED sensor can be mounted on the bicycle hub of both wheels and will be activated through movement.

Steps:

1. Remove sticker.
2. Mount the sensor on the hub.
3. Ensure the sensor is correctly positioned.
4. The sensor will be activated by movement, indicated by a blue light flashing.

Cadence Sensor Installation

The CADENCE sensor can be mounted on the crank arm or pedal. It is activated through movement.

Steps:

1. Remove sticker.
2. Mount the sensor on the crank arm or pedal.
3. Ensure the sensor is correctly positioned.
4. The sensor will be activated by movement, indicated by a blue light flashing.

Manufacturer Information

SIGMA-ELEKTRO GmbH
Dr.-Julius-Leber-Straße 15
67433 Neustadt, Germany

Website: sigmasport.com