Philips Pacific LED gen5 WT490C WT495C

General Safety and Handling Precautions

• Prevent water from entering the luminaire during installation and use. Refer to the manual for detailed installation instructions.
• Do not open the luminaire when it is powered on due to the risk of electrostatic discharge.
• The housing is made of non-metallic material.
• Prevent dust accumulation on the housing surface.
• Clean the luminaire only with a damp cloth containing an antistatic agent.
• Handle with care, especially electronic components, as they are sensitive to electrostatic discharge (ESD). Use static-free gloves during installation and maintenance.
• Do not stare directly into the LED light beam.
• Remove protective foil from optical parts after installation to avoid scratches and dirt.
• Installation and wiring must be performed by a qualified electrician in accordance with the latest IEE electrical regulations or national requirements.
• Do not touch the LEDs or the contacts within the connector.
• Install optical plates carefully to protect the boards.
• Driver insulation is basic according to IEC 61847-1.
• Observe precautions for handling electrostatic sensitive devices.

Product Information

The Philips Pacific LED gen5 series includes models WT490C and WT495C. These luminaires are designed for various applications and come with different driver options (PSU, SIA, SEIA) and configurations (TW, TCW5, W5, W7).

Key Features:

• Indoor use
• LED technology
• Available in 220V, 50Hz/60Hz
• IP66 and IK08 rated
• Light source energy efficiency class: C (approx. 7% improvement in lumen output for 4000K, 6500K options)

Installation Instructions

Ceiling Mounting (Standard Applications)

The luminaire can be mounted on the ceiling using the provided mounting bracket. Ensure the bracket is securely attached to the ceiling surface. The luminaire then attaches to the bracket.

Wall Mounting

For wall mounting in vertical or horizontal positions, special sets of screws and nuts (e.g., WT470Z SCREW VP SET) may be required. Refer to specific mounting instructions for details.

Wiring and Connections

The luminaire features a connector system for power input and output. Ensure correct wiring according to the diagrams provided, paying attention to phase (L1, L2, L3), neutral (N), and earth (⏚) connections. Cable entry is typically through an M20 or M25 gland, accommodating cables with diameters from 7 mm to 14 mm or 17 mm.

Various wiring configurations are shown for different driver types (PSU, SIA, SEIA) and model variants (e.g., WT490C/WT495C TW3, WT490C/WT495C TCW5, WT490C W5, WT490C W5-TW).

Connector Details:

• Female Connector: L1, L2, L3, N, ⏚
• Male Connector: L1, L2, L3, N, ⏚
• For TW versions with DA/N and DA/Ls: Female connector: DA/N, DA/Ls, N, L, ⏚; Male connector: DA/N, DA/Ls, N, L, ⏚

Ensure proper cable strain relief and secure connection of wires.

Electrical Characteristics

The table below outlines key electrical characteristics for various luminaire types and driver configurations:

Inrush Current: The graph illustrates the inrush current characteristic, showing Imax at Tref and settling to Inom.

Maintenance Instructions

1. Do not touch electronic components; they are under high voltage and ESD sensitive.
2. Use static-free gloves to avoid marks on the luminaire during installation or maintenance.
3. For cleaning:
• Dust: Use micro fiber cloths.
• Fingerprints, etc.: Use a cleaner for synthetic materials with antistatic properties.
4. Do not stare into the LED light beam.
5. Remove protective foil after installation to avoid scratches and dirt on optical parts.
6. The luminaire must be installed and wired by a qualified electrician according to current regulations.
7. Do not touch LEDs or connector contacts.
8. Install optical plates carefully to protect the boards.
9. Driver insulation is basic according to IEC 61847-1.

Important Note: The light source, control gear, and external flexible cable in this luminaire should only be replaced by the manufacturer, their service agent, or a similarly qualified person.

Emergency Lighting

For emergency lighting applications, a DC power connection (186-250 V DC) is required for PSED and SEIA versions.

Product Warranty and Lifecycle

Storage, installation, use, operation, and maintenance must be performed exactly according to the instructions in this manual and any other provided instructions to guarantee safe use over the product's entire lifetime. Failure to adhere to these instructions will invalidate your warranty entitlement. Bolts with indicated torque values must be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened to the required torque specification for maximum strength.

Energy Efficiency Class: The energy efficiency class of the light source is indicated in the table or on the label.

Service and Support

For an overview of all spare parts for a luminaire, refer to the detailed instructions in the service manual available via the Signify Service tag apps (Android and iOS).

Multilingual Information

This document includes safety and handling information in multiple languages:

• General Safety: GB, FR, DE, NL, LT, EE, PT, DK, NO, FI, CZ, TR, HR, GR, BG, RU, LV, IT, ES, SE, HU, PL, RO
• Basic Insulation: GB, SE, ES, NO, FI, DE, FR, IT, NL, DK, HU, BG, RU, PL
• Light Source Replacement: GB, ES, PT, DE, FR, IT, NL, DK, SE, NO, CZ, HU, PL, RO, FI, TR, HR, GR, BG, RU, LV, EE, SI
• Storage, Installation, Use, Operation, Maintenance: GB, ES, PT, DE, FR, IT, NL, DK, SE, NO, FI, HU, PL, RO, CZ, TR, BG, GR, RU, SK, HR, LT, LV, EE, SI
• Energy Efficiency Class: GB, ES, PT, DE, FR, IT, NL, DK, LT, GR, PL, RO, CZ, FI, SE, HU, SK, HR, LV, EE, BG