VEVOR Hand Gun Safe User Manual

IMPORTANT SAFEGUARDS

Warning: To reduce the risk of injury, user must read instructions manual carefully. Failure to do so can result in serious injury.

Use precautions:

1. DO NOT SIT, STAND OR CLIMB ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or near this item.
3. Use as intended only. Keep away from sharp points, blades and other items, so as not to scratch the product.
4. Flammable: Keep away from open flame. This product will ignite and burn if brought into contact with an open flame.
5. Battery Replacement: When the batteries are not high enough and must be replaced immediately. To replace the batteries, turn off the hand gun safe first. Replace the old batteries with new ones of the same type, make sure that the polarity connections are correct (see the polarity indications at the bottom of the battery compartment). Reinstall the battery cover.

SAVE THESE INSTRUCTIONS

PRODUCT PARAMETERS

FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

PARTS LIST

Thank you very much for choosing this Hand Gun Safe. Please read all of the instructions before using it. The information will help you achieve the best possible results.

Diagram Description: The diagram shows the components of the gun safe. It includes a mounting bracket, panel with buttons and biometric scanner, emergency keyhole, thumb screw, anti-crash foam, holes of mounting hook, plug nut hole, connector protection bracket, set reset button, battery compartment, mounting screws, thumbscrew, plug nut and studs, backup keys, and LED light.

Parts List:

• ① Mounting Bracket
• ② Panel (Buttons & Biometric Scanner)
• ③ Emergency Keyhole
• ④ Thumb Screw
• ⑤ Anti-crash Foam
• ⑥ Holes of Mounting Hook
• ⑦ Plug Nut Hole
• ⑧ Connector Protection Bracket
• ⑨ Set reset Button
• ⑩ Battery Compartment
• ⑪ Mounting Screws×4
• ⑫ Thumb Screws×1
• ⑬ Plug Nut×1 And Studs×1
• ⑭ Backup Keysx2
• ⑮ Led Light

ADJUSTING THE FOAM

There are two slots cut into the foam inside the Gun Safe. Before installing the gun safe, adjust the slots on the foam to fit the size of your gun.

1. Take out the little foams of the slots.
2. Cut little foams to adjust your gun size.
3. Put the cut foams back into the slots to hold your gun firmly.

Diagram Description: An illustration shows how to adjust the foam slots inside the gun safe to accommodate different gun sizes.

BATTERY INSTALLATION

To get started, ensure the bottom of the safe and the door are not obstructed before opening.

1. Insert one of your backup keys into the keyhole at the front of the gun safe. Push the key in and turn it counterclockwise to open the gun safe. (Note: Do not lock the key inside the safe - this is an emergency key and will open the safe if you have lost your code.)
2. Locate the battery compartment inside the gun safe, and pull out the battery compartment.
3. Insert 4xAAA batteries into the battery compartment. Pay attention to the "+" and "-" signs. The "-" end of the batteries goes against the spring inside of the compartment.
4. Repeat the above steps for battery replacement.

Diagram Description: A diagram shows the location of the keyhole and battery compartment within the gun safe.

BATTERY WARNINGS

• Always insert batteries correctly about polarity (+ and -) as marked on the battery and the product.
• Exhausted batteries should be immediately removed from the product and properly disposed of.
• Do not mix old and new batteries.
• Do not mix alkaline, standard(carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.

LOW BATTERY WARNING

If the indicator light will light up red 6 times with 6 times beeps when opening the Gun Safe by the electronic way, your battery level is critically low and your Gun Safe needs to be replaced the 4 new batteries.

FACTORY PRESET CODE

Factory preset code: 1234.

Factory preset fingerprint: blank (any fingerprint can unlock)

Enter the factory code 1.2.3.4. If or any fingerprints, the green led will light up.

Important: All safe models initially work with the safe code 1.2.3.4. It is therefore important to reset your safe with a new user code you have personally selected to provide maximum security.

TO SET AN USER CODE

1. Press the "set button" until you hear 2 beeps and the green light flashes twice, you can start to set your user code with 3-6 digits long.
2. Press the "set button" again to confirm the user code. When you hear 2 beeps and the green light flashes twice, the new code has been set successfully.

Diagram Description: A diagram indicates the location of the "Set Button" on the safe's panel.

TO SET PRIMARY USER FINGERPRINT

1. Press the "set button" until you hear 2 beeps and the green light flashes twice. Put one finger on the fingerprint scanner.
2. Repeat three times. When you hear 2 beeps and the green light flashes twice, the Primary User Fingerprint has been set successfully.

(Total of 100 pieces of fingerprints can be set. The setting method is the same as the Primary User Fingerprint.)

Note: You only have 10 seconds to set the code or fingerprint. When you hear 3 beeps and the red light flashes 3 times, the code or fingerprint setting fails.

ERROR ALARM

Enter the wrong password 3 times or fingerprint 5 times, the buzzer alarm for 30 seconds, and all buttons/fingerprints invalid when the alarm sounds. The panel locks for one minute. Press any button or fingerprint, you will hear 3 beeps and the red light flashes 3 times.

The gun safe can still be opened using the backup keys.

After one minute, the gun safe will automatically resume normal operation with one beep sound issue and the indicator light flashes green.

If the input is wrong again, the buzzer alarms for 30 seconds and the panel is locked for 5 minutes.

Note: The 30-second buzzer alarm is not affected by the mute mode.

MUTE FUNCTION

Press the "4" button for more than 2 seconds, the green light flashes, it means the mute function is on/off.

RESTORE FACTORY SETTINGS

Keep pressing the set button until you hear a beep, the reset is successful.

MOUNTING YOUR GUN SAFE

Use proper drilling tools and mounting hardware based on the type of surface you mount the gun safely onto. Supplied screws are intended to be used on wooden surfaces.

Ensure you have enough clearance for the lid to open properly before mounting the gun safely.

Your Aureole gun safe will automatically lock when you fully close the lid.

1. Open the box and take out the mounting bracket and screws.
2. Use the included 4x mounting screws to install the bracket onto the desired place.
3. Slide the gun safe onto the bracket mounting hook, and fix the gun safe to the bracket with a thumbscrew from inside the gun safe.
4. Close the gun safe. Now the gun safe should be ready for use.

Diagram Description: Diagrams illustrate the mounting bracket, screws, hook, and thumbscrew, as well as the overall gun safe assembly.

Important Notes for Mounting:

• The bracket is allowed to be installed on the left, right and back side of the gun safe, but the thumbscrew must be attached to the bracket.
• Do not let the gun safe door face the floor when you are mounting the gun safe in the vertical direction to avoid your property from damage.

CORRECT DISPOSAL:

This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.