VEVOR Safe Box User Manual

Contact Us

For product questions or technical support, please contact: CustomerService@vevor.com

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret the user manual. Product appearance is subject to the received item. VEVOR will not provide further notice for technology or software updates.

Important Safety Information

[⚠] To reduce the risk of injury, user must read instructions manual carefully.

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

European Directive Compliance: This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

WARNING

1. Danger of Tipping Over:
   • A child or adult can tip the safe and be killed or seriously injured.
   • Serious injury may occur to children and adults if the safe is not secured before installation.
   • Children should not play with or around the safe at any time.
2. Important: Please do not put the emergency key or the external power box inside the safe box.

Instructions

Thank you for choosing this safe box. Please read all instructions before using it to achieve the best possible results.

Product Overview and Components

The safe box interior is organized with a gun rack for rifles on the left, a partition creating compartments, and a built-in storage locker. A pistol rack is included, along with multiple bullet boxes. Features also include an LED light, battery box, and a setting button. External access points are digital keys and an emergency key hole, operated via a handle.

Technical Parameters

Parts List

• Built-in Storage Key*2 [key icon]
• Emergency Key*2 [key icon]
• Expansion Bolt*5 (10*50) [bolt icon]
• External Power Box*1 [power cable icon]

Getting Started

1. Move the silver part of the keyboard lock to reveal the emergency keyhole.
2. The emergency key channel will now be exposed.
3. Insert the emergency key into the keyhole and turn it 35 degrees counterclockwise.
4. Turn the handle clockwise to open the safe.

Tip: Use the emergency key for the first opening. After installing batteries, set the fingerprint and key password.

Install Batteries

1. Open the battery box cover.
2. Insert 4 AA batteries and replace the battery cover. (Caution: Do not use Lithium Batteries or different brands of rechargeable batteries.)
3. Proceed to the next step.

The original password is 123456#. No fingerprint recognition is set for the factory blank fingerprint.

Password Setting Method (Two Groups of Password)

1. Management Code: After unlocking, touch the screen to wake it up. Press '00', then press the green setting button. Enter the new password (3-12 digits) and end with '#'.
2. Personal Code: After unlocking, touch the screen to wake it up. Press '11', then press the green setting button. Enter the new password (3-12 digits) and end with '#'.

Tip: In standby mode, press and hold the green button (fingerprint delete key) for about 5 seconds. A long "Di" sound indicates all fingerprints and passwords have been deleted successfully, restoring factory settings. Any fingerprint can then lock the safe.

Set Fingerprint

Tip: If a fingerprint is not set successfully, any fingerprint can open the door. The safe can store up to 30 fingerprints.

1. When the door is open, press the setting button.
2. After two short "beep" sounds, the scanner light will turn on. Collect fingerprints on the scanner four times.
3. Two short "beep" sounds followed by a long "beep" indicate successful fingerprint registration.
4. Setting Failure: Three short "beep" sounds indicate registration failure.

Setting Failure Causes:

1. Weak current: Change the battery.
2. Finger peeling: Replace the finger.

Open the Safe

1. Enter the correct user password. The electromagnet will engage, the screen will display lock status. Turn the handle clockwise to open the door.
2. Press the correct fingerprint. The electromagnet will engage, the screen will display lock status. Turn the handle clockwise to open the door. (Blank fingerprints are not allowed.)
3. If identification is successful, the screen will display the unlock status.

Alarm Function

1. In standby state, press '*'. You will hear a "beep" sound, and the digital pad will turn off, indicating alert status. The safe will alarm if it vibrates. Enter password or scan fingerprint to open the door to disarm the alarm automatically. The warning sound lasts 30 seconds.
2. The warning sound will last 30 seconds if you scan the wrong fingerprint five times or input the wrong password three times.

Tips: After an alarm, enter the correct fingerprint or password. The electromagnet will close for 5 seconds, and the alert state will be lifted automatically.

Noise Elimination Function

Touch the touch pad to wake it up. Press "11#" to turn all sounds on or off.

Undervoltage Indication

1. The gun safe requires four 1.5V alkaline batteries.
2. If the voltage is insufficient, a buzzer will sound ("beep"), reminding the user to replace the battery.

Note: It is recommended to use ordinary batteries; avoid using lithium batteries or different brands of rechargeable batteries.

Mounting Instructions

The safe can be mounted to a wall or floor.

• Drill appropriate size holes for the anchors you are using.
• Mount the safe by running screws from inside the safe and securing to anchors. Ensure the safe is mounted securely on the floor.
• Use proper drill tools depending on the floor type (wood, tile, or concrete).