| Brand: | GOL PUMPS | Flow Rate: | 33.3 GPM |
| Model: | GMD3-400 | Flow Max: | 63 GPM |
| Head Rate: | 28.21 FEET | Flow Min: | 9 GPM |
| Head Min: | 10 FEET | RPM: | 3450 rpm |
| Head Max: | 36.6 FEET | Normal Power P2: | 0.5 HP |
| Fluid: | Water | Fluid Temperture: | at about 32 °F - 176 °F |
| Liquid Density: | 1.2 kg/Dm³ = 2.65 lb | Fluid Viscosity: | 8.90 × 10⁻⁴ Pa·s |
| Kind of Workiny: | Horizontal | Delivery size: | 40 mm 1 1/2" Thread & Flange |
| Suction size: | 40 mm 1 1/2" Thread & Flange | Made in: | CHINA |
| Power P2: | 0.4 KW | Phase (PH): | 3 |
| Rate Voltage: | 220 V | Capacitor Need: | NONE |
| Frequency: | 60 Hz | Rated Speed (rpm): | 3450 rpm |
| Current (A): | 1.2 A | Cos Φ: | 0.85 |
| Degree of Protection (IP): | IP 55 | Safety Protection Degree: | E |
| Length of Cable: | 2 M | Kind of Plug: | NONE |
| Ambient Temp: | 40°C = 104°F |
| Pressuer Rating: | PN 6 | Min. Fluid Temp: | 0°C = 32°F |
| Max. Fluid Temp: | 80°C = 176°F | Ambient Temp: | 40°C = 104°F |
| Humidity %: | 50% |
| Installation status: | Horizontal | Variable frequency: | NONE |
| Component | Material |
|---|---|
| 1- Front Casing: | CFRPP |
| 2- Impellerr: | CFRPP |
| 3- Rear Casing: | CFRPP |
| 4- Magnet Capsule: | PP |
| 5- O-ring: | FKM (EPDM) |
| 6- Stationery Bush: | Silicon Carbide |
| 7- Rotation: | Silicon Carbide |
| 8- Rear Thrust: | CFRPP |
| 9- Mouth Ring: | PTFE |
| 10- Liner Ring: | Alumina Oxide |
| 11- Lock Pin: | CFRPP |
| 12- Inner Flange: | CFRPP |
| 13- Outer Flange: | CFRPP |
A performance curve graph shows Head (in meters) on the Y-axis against Capacity (in Liters per minute) on the X-axis. Two curves are plotted, labeled GMD-401 and GMD-400, illustrating the head generated by the pump at different flow rates.
An image displays a side view of the GOL PUMPS MAGNET PUMP GMD3-400, showing the motor end with cooling fins and a nameplate, connected to the pump casing with a flange connection.
A cross-section diagram illustrates the internal components of the pump. Key numbered parts include: 1- Front Casing, 2- Impeller, 3- Rear Casing, 4- Magnet Capsule, 5- O-ring, 6- Stationery Bush, 7- Rotation, 8- Rear Thrust, 9- Mouth Ring, 10- Liner Ring, 11- Lock Pin, 12- Inner Flange, 13- Outer Flange.
An engineering drawing shows the overall dimensions of the pump with labels a, b, c, d, e, f, g, H, L, W. The following table provides these dimensions in inches and millimeters:
| Dimension | in | mm |
|---|---|---|
| A | 110 | |
| B | 54 | |
| C | 98 | |
| D | 95 | |
| E | 130 | |
| F | 87 | |
| G | 150 | |
| I | 12 | |
| W | 140 | |
| H | 255 | |
| L | 452 |
Suitable for handling:
- Corrosive Acids, Alkalis, Solvents, Brines,
- Plating Solutions, Sterile Solutions, and other
- Mildly Corrosive Chemicals and Solutions that are Compatible with the Pumps Material of Construction.
Standard Approval: CE Marking [CE]
