Trumeter APM Gateway Quickstart Guide

Device Diagram

1. POWER SUPPLY: 12-24 VDC/VAC

2. APM CONNECTIONS x4

3. GATEWAY STATUS LED: Indicates cloud connection status.

4. RJ45 ETHERNET PORT: For network connectivity.

5. EARTH MOUNTING POINT: For grounding the device.

Hardware Configuration

i. Device Wiring

1. Connect APM(s) to the APM Gateway as per wiring diagram.
2. Plug in Ethernet cable to the RJ45 ethernet port.
3. Configure APMs to ensure alarms are set using the APM configurator software.

ii. Powering Device

1. Power the APM Gateway.
2. Status LED:
   RED - Not Connected to Cloud
   GREEN - Connected to Cloud
3. Confirm each APM connection Link LEDs are active depending on how many meters are connected to the APM Gateway.

Cloud Access

To access the Trumeter Cloud dashboard, go to cloud.trumeter.com.

Creating a New User Account

1. Go to cloud.trumeter.com.
2. Click 'Sign Up' to go to the registration screen.
3. Once registered, a confirmation email will be sent to the email address used for the account.

Adding a New Gateway

1. Login to cloud.trumeter.com.
2. Click the (+) to add a new device.
3. Add serial number and model.
4. 'REFRESH' the browser.
5. Device will be claimed and added to the list of gateways.

Wiring for APM Link

Diagram illustrating the wiring connection for APM Link.

Connection of a Relay to Open Collector Output - Using DC PSU

Diagram showing the connection of a relay to an open collector output using a DC power supply unit.

Status LEDs

APM Link LEDs: GREEN - link active, output on.

APM DOut LEDs: GREEN – SP2 connection open/active.

GATEWAY Status LED: GREEN – Cloud connection; RED - Cloud disconnected; BLUE - software update.

Specification

Connections

Environment

Mechanical Dimensions

Diagram showing the mechanical dimensions of the APM Gateway, including mounting points and port locations.

Safety Warnings

WARNING: INSTALLATION AND MAINTENANCE MUST BE CARRIED OUT BY SUITABLY QUALIFIED AND COMPETENT PERSONNEL ONLY. Install this product in accordance with local regulations, codes and instructions. An external fuse should be fitted in-line with the PSU. Recommended fuse: 500mA/250V Type T with a breaking capacity of 35A or greater.

Signal cables connected to this device must not exceed 30 metres long. If signal cables are routed outside the building, install extra surge-protection devices.

12V-24V power supply, current input, USB and all outputs: Observe maximum allowable voltages. All circuits connected to these connectors must be limited-energy and insulated by double/reinforced insulation from mains voltages.

MAINTENANCE: Before cleaning, inspection or maintenance, isolate all power sources to the unit. There are no user-serviceable parts inside this unit. Never open the case. Inspect all external wiring connections at regular intervals. Replace any damaged wiring and tighten any loose connections. To clean the unit, use a dry cloth to wipe the casing. Take great care connecting the supply. If you connect power to the wrong terminals, it may destroy the unit.

Further Information

Use of APM Link requires APM Software version 28 or above and APM Link must be enabled on the APM using the APM Configurator application.

DHCP server required for correct operation.

Product page: https://www.trumeter.com/product/apm-gateway/

Trumeter Cloud pricing plans: https://www.trumeter.com/solutions/cloud/plans/

Help: https://www.trumeter.com/help/tech-tips/

APM Software Download: https://www.trumeter.com/help/apm-software-download/

Trumeter (Europe)
Trumeter, Pilot Mill, Alfred Street, Bury, Lancashire BL9 9JR, United Kingdom
Tel: +44 161 674 0960
Email: sales.uk@trumeter.com

Trumeter (The Americas)
Trumeter, 6601 Lyons Rd, SUITE H-7, Coconut Creek, Florida, FL 33073, USA
Tel: +1 954 725 6699
Email: sales.usa@trumeter.com

Asia Pacific Distributor
Innovative Design Technologies Sdn. Bhd, Lot 5881, Lorong Iks Bukit Minyak 1 Taman Perindustrian Iks, 14000 Bukit Tengah Penang, Malaysia
Web: www.idtworld.com
Tel: + 604 5015700
Email: info@idtworld.com

www.trumeter.com