This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

• (1) This device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Warning

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

IC Warning

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Email Support: ctreatlife.tech

Tech Support: www.treatlife.tech/pages/support

PRODUCT OUTLINE

The Treatlife Dimmer Plug and Remote Kit allows for wireless control of lights. The kit includes a dimmer plug that connects to a power outlet and a remote control for operation. The plug features an indicator light and a button for manual control.

PRODUCT SPECIFICATIONS

PAIRING INSTRUCTIONS (RF REMOTE CONTROL AND SOCKET PAIRING)

If the remote control cannot control the socket or if an additional remote control needs to be paired, follow these steps:

1. Quickly press the power button on the socket three times. The white indicator light will start flashing, indicating the RF pairing mode.
2. Press and hold the ON/OFF button on the remote control for about three seconds, aiming it at the flashing socket to complete the pairing process. Once successful, the white indicator light on the socket will stop flashing.

(Each socket can be paired with up to 8 remote controls.)

Minimum Brightness Setting Steps

To set the minimum brightness:

1. Press and hold the ON/OFF button on the remote control for 8 seconds. The socket indicator light will start rapidly flashing white.
2. Use the Increase Brightness [+] and Decrease Brightness [-] buttons on the remote control to adjust the minimum brightness of the light bulb.
3. Press and hold the ON/OFF button for 3 seconds again to confirm the minimum brightness setting.

PRODUCT FUNCTIONS

Socket Indicator Light

• Power Status: Steady light indicates the socket is turned on; no light indicates it is turned off.
• RF Pairing Mode: White flashing light.

Socket Button

• Single click: Power on/off.
• Long press: Adjust brightness.

Remote Control Buttons

• Power Button: Single click to turn the connected device on or off.
• Increase Brightness Button [+]: Single click to increase brightness. Long press to continuously increase brightness.
• Decrease Brightness Button [-]: Single click to decrease brightness. Long press to continuously decrease brightness.

BATTERY INSTALLATION / REPLACEMENT

The remote control uses a CR2032 battery. To replace the battery:

1. Gently pry open the remote control casing.
2. Remove the old CR2032 battery.
3. Insert the new CR2032 battery, ensuring correct polarity.
4. Snap the casing back together.

Common Issues

• Light is flashing: Try increasing the minimum brightness (refer to Minimum Brightness Setting Steps).
• Minimum brightness is too bright: Try decreasing it (refer to Minimum Brightness Setting Steps).
• Light doesn't turn on after power-up: Try increasing the minimum brightness. If the issue persists, check if the socket or the bulb is damaged.
• Remote control unresponsive or not working properly: The battery may be low. Replace the CR2032 battery.