Wireless-Tek WI-AP218AX Quick Installation Guide

1. Packing Content

• 1 x AP (WI-AP218AX)
• 4 x Plastic Anchors
• 4 x Self-Tapping Screws
• 1 x Ethernet Cable
• 1 x Quick Installation Guide

2. Appearance Overview

Model: WI-AP218AX

3. Typical Connection

Bypass Mode Topology

A diagram shows a single AP connected to a PoE Switch via an Ethernet cable. The PoE Switch is connected to an AP Controller.

AC Gateway Mode Topology

A diagram shows a single AP connected to a PoE Switch via an Ethernet cable. The PoE Switch is connected to a Router, which then connects to the Internet.

LED Indicators

Port and Button

• RESET: Reset button, used to restore factory settings. Holding down for 10 seconds reverts to factory settings.
• WAN/PoE: 10/100/1000Mbps Base-T Ethernet Port, supports 802.3af/at PoE Input. Connect to a PoE switch supporting 802.3af output or an upstream switch.
• LAN: 10/100/1000Mbps Base-T Ethernet port. Connect to wired LAN devices like a PC.
• DC IN: 12V, 1A DC Input Port. Power the AP via a 12V DC adapter.

4. Device Installation

Ceiling Mounting

1. Place the bracket in the center of the ceiling and mark screw hole positions and the Ethernet cable position.
2. Drill holes at the marked positions using a hammer drill.
3. Insert plastic anchors into the holes using a rubber hammer. Align the bracket's screw holes with the ceiling holes and secure the bracket with self-tapping screws.
4. Power the AP by connecting a PoE switch to the WAN/PoE port or a power adapter to the DC Input port.
5. Align the AP's slots with the bracket's hooks. Push the AP until it is securely fixed.

5. Power Supply

Power via PSE Device

The APs can be powered via a PoE switch that supports 802.3at PoE output. Connect the PoE switch to the AP's WAN/PoE port.

Power via Power Adapter

Some APs can be powered via a power adapter that supports 12V DC output. Connect the power adapter to the DC Input port.

6. Configuration Method

Method 1: Connect via Wireless Signal

1. Connect your computer to the wireless signal of the AP. The default SSID is "WI-TEK xxxx".
2. The default password is "88888888".

Method 2: Connect via Ethernet Cable

1. Connect your computer to the AP using an Ethernet cable.
2. Step 1: On your computer, set a static IP address within the same subnet as the AP (e.g., 192.168.1.xx).
3. Step 2: Launch a web browser (e.g., Google Chrome, Firefox) and navigate to 192.168.1.88.
4. The default login username is "admin" and the password is "admin".
5. Step 3: After logging in, navigate to [Wizard] on the left-side menu to set up the access point.
6. Step 4: Select the appropriate operation mode (Fit AP Mode or Wireless Router Mode) and follow the wizard instructions.

Note: Resetting the AP will revert it to Fit AP Mode.

• Fit AP Mode: Default Login IP: 192.168.1.88, Credentials: admin/admin.
• Wireless Router Mode: Default Login IP: 192.168.11.1, Credentials: admin/admin.

7. Cloud Management Settings

1. Launch your web browser and enter http://cloud2.wireless-tek.com.
2. Register an account using your username or email and password.
3. Log in to your cloud account.
4. Click "ADD NETWORK".
5. Fill in the group name and location, then click "save".
6. Click "next".
7. Enter the device's serial number (17-digit SN code found on the device sticker) and click "ADD". Click "FINISH" to complete the configuration.
8. In the device options, you can see the bound device information.
9. Click "Tunnel", select the binding device type, and click "EWEB" to log in to the device.

8. FAQ

Q1. The LED is not lit.

A1: Check if the PoE switch supports 802.3af/at.

A2: Ensure the PoE switch is outputting the correct voltage.

A3: Verify the Ethernet cable supports PoE function.

Q2. What can I do if the login window does not appear?

A1: Ensure your computer has a static IP address in the 192.168.1.xxx range.

A2: Try using a different web browser.

A3: Reboot your AP device and try again.

A4: Disconnect the internet connection, log in, and then reconnect to the internet.

Warranty Card

Username:

Address:

Telephone No.:

Purchase Shop:

Purchase Address:

Product Model No.: WI-AP218AX

Purchase Time:

Serial No.:

Dealer Signature:

• If the product has defects within three months of purchase, Wireless-Tek will provide a new product of the same model.
• If the product has defects within the three-year warranty period, Wireless-Tek will provide professional maintenance service.
• Proof of purchase and a complete product serial number are required for warranty services.
• Defects not caused by workmanship or product quality, such as natural disasters, water damage, extreme thermal or environmental conditions, damaged stickers, or lost warranty cards, will disqualify the product from the limited warranty.