Wireless-Tek WI-AP210-Lite Quick Installation Guide

1. Packing Content

• 1 x WI-AP210-Lite Access Point
• 4 x Plastic Anchors
• 4 x Self-Tapping Screws
• 1 x Ethernet Cable
• 1 x Quick Installation Guide

2. Appearance Overview

LED Indicators

Ports and Buttons

Note: The WAN/PoE port also functions as a 12V DC Input Port.

3. Typical Connection

Bypass mode topology: A PoE switch is connected to the AP's WAN/PoE port.

AC Gateway mode topology: A router is connected to the AP's WAN/PoE port, and the AP provides Wi-Fi access.

4. Device Installation

Ceiling Mounting

1. Place the mounting bracket in the center of the ceiling. Mark the positions for the screw holes and the Ethernet cable opening.
2. Drill holes at the marked positions using a hammer drill.
3. Insert the plastic anchors into the drilled holes using a rubber hammer. Align the screw holes in the bracket with the holes in the ceiling and secure the bracket using the self-tapping screws.
4. Power the AP by connecting a PoE switch to the WAN/PoE port or a 12V DC power adapter to the DC Input port.
5. Align the slots on the AP with the hooks on the bracket. Push the AP to one side until it is securely fixed.

5. Power Supply

Power via PSE Device: The APs can be powered via a PoE switch that supports 8002.3af PoE output.

Power via Power Adapter: Some APs can be powered via a 12V DC power adapter.

6. Configuration Method

Method 1: Connect via Wireless

Connect your computer to the AP's wireless signal. The default SSID is "WI-TEK xxxx" and the default password is "88888888".

Method 2: Connect via Ethernet Cable

1. On your computer, set a static IP address within the same subnet as the AP (e.g., 192.168.1.xx).
2. Launch a web browser (e.g., Google Chrome, Firefox) and enter 192.168.1.88 in the address bar. The default login username is "admin" and the password is "admin".
3. After logging in, navigate to [Wizard] in the left-side menu to set up the access point.
4. Select the appropriate operation mode:
   • Fit AP Mode: Choose this if a router already exists in your network. Default Login IP: 192.168.1.88 (admin/admin).
   • Wireless Router Mode: Choose this if no router exists. Default Login IP: 192.168.11.1 (admin/admin).
   Note: Resetting the AP will revert it to Fit AP mode.

7. Cloud Management Settings

1. Launch your web browser and enter http://cloud2.wireless-tek.com in the address bar.
2. Register an account using your username or email address.
3. Log in to your cloud account with the registered credentials.
4. After successful login, follow these steps to bind the device to your cloud account:
   1. Click "ADD NETWORK".
   2. Fill in the group name and location, then click "save".
   3. Click "next".
   4. Enter the device's serial number (the 17-digit SN code is on the sticker on the back of the device), click "ADD" to create the network, and then click "FINISH". The configuration is complete.
   5. You can view the bound device information in the relevant device options.
   6. Click "Tunnel", select the binding device type, and click "EWEB" to log in to the device.

8. FAQ

Q1. The LED is not lit.

A1: Please check if the PoE switch is 8002.3af/at compliant.
A2: Ensure the PoE switch is outputting the correct voltage.
A3: Verify that the Ethernet cable supports PoE functionality.

Q2. What can I do if the login window does not appear?

A1: Check if your computer has a static IP address set in the 192.168.1.xxx range.
A2: Try using a different web browser.
A3: Reboot your AP device and try again.
A4: Disconnect the internet connection temporarily, try logging in, and then reconnect to the internet.