SUBMITTAL DATA SHEET
High Wall Heat Pump System
Location: [Not Specified]
Engineer: [Not Specified]
Submitted to: [Not Specified]
Submitted by: [Not Specified]
Reference: [Not Specified]
Approval: [Not Specified]
Date: [Not Specified]
Construction: [Not Specified]
Unit #: [Not Specified]
Drawing #: [Not Specified]
Product Overview
This document provides the submittal data sheet for the High Wall Heat Pump System.
Image of the indoor unit (white, rectangular with a grille) and the outdoor unit (grey, rectangular with a fan grille). Certifications shown include ARI Certified, ETL LISTED, and Intertek.
Efficiency Ratings
| Rating | Cooling | Heating |
|---|---|---|
| SEER2 | 19.5 | - |
| EER2 | 9 | - |
| HSPF2-4 | - | 9.3 |
| COP | - | 3.25 |
Performance Data
Cooling Performance
| Parameter | Value (Btu/hr) |
|---|---|
| Rated Capacity | 12000 |
| Min/Max Capacity | 7400~12100 |
| Moisture Removal (L/h) | 1.33 |
| Standard Operating Range (°F/°C) | -13~75 (-25~50) |
| Conditions | Indoor: 80°F DB/67°F WB Outdoor: 95°F DB/75°F WB |
Heating Performance
| Parameter | Value (Btu/hr) |
|---|---|
| 1. @ 47°F Rated | 12000 |
| 1. @ 47°F Min/Max Capacity | 4300~12700 |
| 2. @ 17°F Rated | 7400 |
| 3. @ 5°F Rated: Capacity / COP | 6700 / 2.20 |
| 3. @ 5°F Max: Capacity | 6700 |
| Standard Operating Range (°F/°C) | -13~122 (-25~24) |
| 1. Conditions | Indoor: 70°F DB/60°F WB Outdoor: 47°F DB/43°F WB |
| 2. Conditions | Indoor: 70°F DB/60°F WB Outdoor: 17°F DB/15°F WB |
| 3. Conditions | Indoor: 70°F DB/60°F WB Outdoor: 5°F DB/5°F WB |
Specifications
Indoor Unit Specifications
| Parameter | Value |
|---|---|
| Indoor Air Flow (Turbo/H/M/L/SI) (CFM) | 353.2 / 294.3 / 235.4 / 176.6 / 129.5 |
| Indoor Noise Level (Turbo/H/M/L/Si) (dBA) | 44.5/40.0/35.0/25.5/17.5 |
| Dimension (W×D×H) | 31.57 x 7.87 x 11.61 inches (802×200×295 mm) |
| Package (W×D×H) | 36.02 x 17.95 x 14.17 inches (915×456×360 mm) |
| Net/Gross Weight | 24.91/35.71 lbs (11.3/16.2 kg) |
Outdoor Unit Specifications
| Parameter | Value |
|---|---|
| Compressor Type | ROTARY |
| Compressor Model | KSK103D33UEZ3 |
| Refrigerant | R454B |
| Refrigerant Oil Charge (mL) | 310 |
| Refrigerant Oil | 5.65 |
| Outdoor Air Flow (Max) (CFM) | 1059.5 |
| Outdoor Noise Level (dBA) | 54.0 |
| Dimension (W×D×H) | 28.35 x 10.63 x 19.49 inches (720×270×495 mm) |
| Package (W×D×H) | 32.87 x 10.63 x 21.26 inches (835×270×540 mm) |
| Net/Gross Weight | 54.89/67.24 lbs (24.9/30.5 kg) |
Electrical Specifications
| Parameter | Value |
|---|---|
| Power Supply | 115V, 60Hz, 1Ph |
| System MCA | 19.5 A |
| Connection Wiring | 14#x4 |
| System MOCP | 20 A |
| Compressor RLA | 14.3 A |
| Outdoor Fan Motor RLA | 0.5 A |
| Outdoor Fan Motor W | 34 W |
| Indoor Fan Motor RLA | 0.6 A |
| Indoor Fan Motor W | 20 W |
| System Power Input @ Cooling (W) | 1333 (630~1320) W |
| System Power Input @ Heating (W) | 1082 (235~1120) W |
| MCA: Min. circuit amps (A) | [Value not explicitly listed, but System MCA is 19.5A] |
| MOCP: Max. over current protection (A) | [Value not explicitly listed, but System MOCP is 20A] |
| RLA: Rated load amps (A) | [Value not explicitly listed, but Compressor RLA is 14.3A] |
| W: Fan motor rated output (W) | [Values listed for Indoor and Outdoor Fan Motor W] |
Piping Specifications
| Parameter | Value |
|---|---|
| Throttle type (Indoor) | N/A |
| Throttle type (Outdoor) | Capillary |
| Liquid Size | 6.35mm (1/4in) |
| Gas Size | 9.52mm (3/8in) |
| Max. Piping Length (ft/m) | 82 (25) |
| Max. Height Difference (ft/m) | 49.20 (15) |
| Max. Pre-charged Length (ft/m) | 24.6 (7.5) |
| Refrigerant Pre-charged Amount (oz/g) | 21.52 (0.61) |
| Additional Charge of Refrigerant (oz/ft) / (g/m) | 0.16 (15) |
| Connection Method | Flared |
Unit Dimensions
Indoor Unit Dimensions
Diagrams showing the indoor unit from the front, side, and top, with dimensions labeled W (width), D (depth), and H (height). A table lists capacities (6K-9K, 9K-12K, 18K, 18K-24K, 30K-36K) with corresponding Body Codes (A, B, C, D, F) and dimensions in inches/mm for Width, Depth, and Height.
| Capacity | Body Code | W (inch/mm) | D (inch/mm) | H (inch/mm) |
|---|---|---|---|---|
| 6K~9K | A | 28-3/4in / 729mm | 7-7/8in / 200mm | 11-1/2in / 292mm |
| 9K~12K | B | 31-5/8in / 802mm | 7-7/8in / 200mm | 11-5/8in / 295mm |
| 18K | C | 38-1/4in / 971mm | 9in / 228mm | 12-5/8in / 321mm |
| 18K~24K | D | 42-5/8in / 1082mm | 9-1/4in / 234mm | 13-1/4in / 337mm |
| 30K~36K | F | 49-5/8in / 1259mm | 11-1/8in / 283mm | 14-1/4in / 362mm |
Diagram illustrating indoor unit installation location selection. It shows a wall with measurements indicating required clearances: 6 inches (15cm) from the top, 4-3/4 inches (12cm) from the sides, and 70 inches (180cm) horizontally. It also shows the indoor unit's internal structure with potential piping exit points on the left and right sides.
Diagram of the indoor unit's rear view, showing mounting points and dimensions W (width) and H (height), with a circular opening for piping (Φ2.5in/65mm). Notes indicate that when the gas side connective pipe is 5/8in (16mm) or more, the wall hole should be 3-1/2in (90mm).
Outdoor Unit Dimensions
Diagrams showing the outdoor unit from the front, side, and top, with dimensions labeled W, W1, W2, H, and D. Specific measurements are provided in inches and millimeters.
Installation Instructions
Indoor Unit Installation
Diagram illustrating indoor unit installation location selection. It shows a wall with measurements indicating required clearances: 6 inches (15cm) from the top, 4-3/4 inches (12cm) from the sides, and 70 inches (180cm) horizontally. It also shows the indoor unit's internal structure with potential piping exit points on the left and right sides.
NOTE: Based on the position of the wall hole relative to the mounting plate, choose the side from which the piping will exit the unit. There are four options for the exit direction of the piping.
NOTE: When the gas side connective pipe is 5/8in (16mm) or more, the wall hole should be 3-1/2in (90mm).
Outdoor Unit Installation Clearance
Diagram illustrating outdoor unit installation clearance requirements. Arrows indicate minimum clearances: 20 inches (500mm) or more on the front and sides if clear, 14 inches (350mm) or more on the rear, and 4 inches (100mm) or more on the sides. A checkmark symbol indicates that all spatial requirements are met.
✔️ Meets all spatial requirements shown in Installation Clearance Requirements above.
Features
- Indoor unit TU1 copper coil
- Humidity control
- 1~100% fan speed setting
- WiFi capability: through WiFi dongle or wired controller with built-in WiFi
- OTA (by using WiFi dongle)
- Multiple control options available:
- Two way communication wired controller: 120N(X6)
- Two way communication wired controller with built-in WiFi: 120N(X6W)
- Infrared wired controller: 120L
- Wireless remote controller
- Third-Party 24V Thermostat*
*24V interface is required.
