Hunter Carrington Isle 13163 Pendant Light Installation Instructions

Preparation for Installation

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a hex nut (E) in place. The other end should have the canopy loop (H) attached. Unscrew the canopy loop ring (I) from the canopy loop (H). Depending on the placement of your junction box, the position of threaded post (F) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and place canopy (G) over the canopy loop (H), so that it is flush with the ceiling. Adjust the position of threaded post (F) on the mounting bracket (A) so that the canopy (G) covers at least half of the exterior threads on the canopy loop (H) while it's securely connected to threaded post (F). Once the ideal position of the threaded post (F) is determined, tighten up the washer (D) and the hex nut (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the threaded post in place.

Assembling the Fixture

There are 4 12-inch rods (K), and 1 6-inch rod (L) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture's wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downrods may be required). Screw rod onto threaded post (M) on the fixture. Pull the fixture wires through the canopy loop ring (I), the top of the canopy (G), and canopy loop (H). Screw the threaded post of the top rod to canopy loop (H) of canopy (G). Have a helper support the fixture's weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

Fixture Components Diagram

Exploded view of the pendant light fixture with labeled parts:

• A: Mounting Bracket
• B: Mounting Screws
• C: Grounding Screw
• D: Washer
• E: Hex Nut
• F: Threaded Post
• G: Canopy
• H: Canopy Loop
• I: Canopy Loop Ring
• J: Rods (includes K and L)
• K: 12-inch Rods (4 included)
• L: 6-inch Rod (1 included)
• M: Threaded Post (on fixture)
• N: Socket
• O: Shade
• P: Socket Ring

NOTICE: In order to use a 12in. rod by itself, you must first remove the threaded post from the 6in. rod and install it on one of the ends of the 12in. rod.

Connecting the Wires

Attach the fixture's wires to the power supply wires from the junction box.

Fixture Wires:

• Black (or Smooth)
• White (or Ribbed)
• Bare Copper (or Green)

House Wires:

• Black (Live)
• White (Grounded)
• Green or Copper (Grounding)

Connection Steps:

1. Connect black fixture wire to black house wire (live).
2. Connect white fixture wire to white house wire (neutral).
3. Connect bare copper/green fixture wire to green/copper house wire (grounding).
4. Twist the ends of the wire pairs together.
5. Use a wire connector to secure each pair, ensuring twists are in the same direction.
6. Loop the fixture's ground wire around the grounding screw (C) and tighten.

If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

Hunter Pro Tip: Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access.

Finishing the Installation

Place the canopy (G) flush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw canopy loop ring (I) onto the canopy loop (H) to properly secure the canopy (G) in place. Secure Shade (O) onto the socket (N) by screwing socket ring (P) tight. Install light bulb (not included) in accordance with the fixture's specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now complete.

Cleaning Tips

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.

Tools You'll Need

Here are the tools you'll need to complete your installation:

• Ladder [ escalera / échelle ]
• Screwdriver [ destornilladore / tournevis ]
• Pliers [ alicates / pince ]
• Wire Strippers [ pelacables / pince à dénuder ]

Hardware Service Kit

Part #: KG22201A57

Model: 13163

Finish: Luxe Gold / Oro de Lujo / Or Grand Luxe

Safety Warnings

⚠️ WARNING:

• To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
• The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
• All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

⚠️ ADVERTENCIA:

• Para evitar una posible descarga eléctrica, antes de instalar su lámpara, desconecte la energía apagando los interruptores automáticos (breakers) que alimentan la caja de salida asociada con la ubicación del interruptor de pared.
• La lámpara se debe conectar a tierra. Si el alambre de conexión a tierra no está presente en el sitio de la instalación, DETENGA inmediatamente la instalación y consulte con un electricista calificado.
• Todo el cableado debe realizarse de acuerdo con los códigos eléctricos locales y nacionales ANSI/NFPA 70. Si no está familiarizado con el cableado, o si tiene duda, consulte a un electricista calificado.

⚠️ AVERTISSEMENT:

• Pour éviter tout choc électrique, avant d'installer le luminaire, coupez le courant en éteignant les disjoncteurs de la boîte électrique associée à l'interrupteur mural.
• Le luminaire doit être mis à la terre. Si le fil de terre du lieu d'installation n'est pas présent, ARRÊTEZ immédiatement l'installation et consulter un électricien qualifié.
• Tout le câblage doit être conforme aux codes électriques nationaux et locaux en vigueur et à la norme ANSI/NFPA 70. Si vous n'avez pas l'habitude de faire ce câblage ou en cas de doute, adressez-vous à un électricien qualifié.

Read and Save These Instructions

These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.

LEA Y GUARDE ESTAS INSTRUCCIONES: Estas instrucciones se proporcionan para su seguridad. Es muy importante leerlas detenidamente y completamente antes de comenzar la instalación de la lámpara.

LISEZ ET CONSERVEZ CES INSTRUCTIONS: Ces instructions sont fournies pour votre sécurité. Il est très important de les lire attentivement dans leur intégralité avant d'entreprendre l'installation du luminaire.